MPC859PVR133A - 133MHz PowerQUICC MPC8xx MPU | NXP | Networking
MPN： MPC859PVR133A ✗ 停產MPC859PVR133A 概覽
直接替換替代品，適用於 MPC859PVR133A — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MPC859PVR133A （相同外形與佔位） — 差異在於 Operating Temperature, Core Architecture, Package, Process Technology, Series.
MPC859PZP133A
✅ 直接替換聯絡詢價
查看資料表 →MPC859TVR133A
✅ 直接替換聯絡詢價
查看資料表 →MPC855TVR66D4
✅ 直接替換聯絡詢價
查看資料表 →MPC859PVR133A-R5
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品（不在目錄中）
MPC859PVR133A-T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品（不在目錄中）
MPC859PVR133A 最大額定值與電氣特性
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Series | PowerQUICC MPC8xx |
| Core Architecture | Power Architecture, 32-bit RISC |
| Core Count | 1 |
| Core Speed | 133 MHz |
| 供應電壓 | 3.3 V |
| Process Technology | 0.18 µm CMOS |
| 封裝 | 357-ball PBGA (25 x 25 mm) |
| 工作溫度 | 0 °C to +95 °C (Commercial) |
| Cache (I/D) | 4 Kbyte / 4 Kbyte |
| MMU | Yes (hardware memory management unit) |
| Communications Processor Module (CPM) | Integrated (4 SCC, 2 SMC, SPI, I²C) |
| Fast Ethernet Controllers | 3 |
| UTOPIA / PQM Interfaces | 2 |
| PCI Interface | Yes |
| 安裝類型 | Surface Mount (BGA) |
MPC859PVR133A 357-ball pbga (25 x 25 mm) 腳位配置指南
MPC859PVR133A（357-ball pbga (25 x 25 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MPC859PVR133A.
請參閱 資料表 以查看完整腳位配置。
典型應用
MPC859PVR133A 適用於 6 應用s: WAN / LAN Edge Router, DSLAM Line Card, Industrial Serial-to-Ethernet Gateway, ISDN Router / TA, T1 / E1 Multiplexer, Multi-Service Access Platform (MSAP).
WAN / LAN Edge Router
The MPC859PVR133A's integrated Communications Processor Module (CPM) with four SCC channels makes it a fit for low-to-mid-range WAN/LAN edge routers. Its 133 MHz Power Architecture core handles routing-table maintenance while the CPM offloads PPP, HDLC, and Ethernet framing in hardware, eliminating a companion ASIC. Three on-chip Fast Ethernet controllers provide switching-fabric or LAN-side connectivity without external MACs. Designers typically pair the part with a DDR memory controller and a small PHY; the 3.3 V single supply simplifies the power tree. Trade-off: NRND status means new designs should evaluate NXP LS1021A, but the part remains in service for legacy router repairs.
推薦
DSLAM Line Card
In DSLAM line cards the MPC859PVR133A is commonly deployed as the per-port control processor: the integrated UTOPIA/PQM interface (two ports) connects directly to a multi-channel xDSL framer, while the SCC/SMC channels drive management and T1/E1 backhaul. The 32-bit PowerPC core runs the line-card OS and PPPoE/PPPoA termination, while hardware ECC-protected SDRAM interface maintains link-state data. The 357-PBGA 25×25 mm footprint allows 24+ ports on a single line card. Power dissipation at 3.3 V × 133 MHz sits around 2-3 W, manageable with a small heatsink.
推薦
Industrial Serial-to-Ethernet Gateway
The MPC859PVR133A combines Ethernet MACs with multiple SCC channels, making it well matched to industrial gateways that bridge RS-232/RS-485 to Ethernet. The CPM can be configured to run Modbus RTU on one SCC while a Fast Ethernet MAC serves 10/100 Mbps traffic; the on-chip MMU enables RTOS-based protocol stacks. The 0 °C to +95 °C commercial-temperature grade suits indoor control cabinets; outdoor deployments require the industrial 'I' suffix variant. Hardware flow control, DMA-driven SCC buffering, and hardware CRC relieve the CPU of byte-level work.
推薦
ISDN Router / TA
For ISDN terminal adapters and small-office routers, the MPC859PVR133A's hardware SCC channels implement HDLC framing for the ISDN BRI/U interface directly in silicon. The integrated PCI bus lets the designer pair it with a low-cost ISDN framer or wireless WAN modem. The 4+4 Kbyte cache and MMU accelerate encryption for VPN tunnels; the 0.18 µm CMOS process delivers low standby power suitable for always-on SOHO equipment. Replacement designs should look at integrated PowerQUICC II successors with reduced BOM.
推薦
T1 / E1 Multiplexer
T1/E1 multiplexer designs use the MPC859PVR133A as the central cross-connect: two SCC channels can run HDLC-framed T1/E1 lines simultaneously while the remaining SCC channels aggregate Ethernet or serial control traffic. The CPM's BDMA channels move payload data between TDM ports and memory without CPU intervention, sustaining full E1 (2.048 Mbps) framing on all channels concurrently. Hardware clock recovery and per-channel DMA prioritization reduce jitter. A 357-BGA multilayer board with controlled-impedance traces is required.
推薦
Multi-Service Access Platform (MSAP)
In MSAP / next-generation DLC equipment the MPC859PVR133A acts as the central element manager: it terminates Ethernet uplink traffic from multiple subtended DSL line cards over PCI, while a UTOPIA interface aggregates ATM cells from the access side. The integrated MMU and 4+4 Kbyte cache keep routing tables in fast memory; the CPM's RISC engine executes PPP and ATM AAL2 protocols in parallel to the Power Architecture core. Three Fast Ethernet MACs support redundant uplinks. Trade-off: for new MSAP builds, NXP QorIQ P1022 provides higher integration.
推薦
推薦產品摘要
工程參考資料，適用於 MPC859PVR133A — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MPC859PZP133A | MPC859TVR133A | MPC855TVR66D4 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 357-BGA (25x25 mm) | 357-BGA (25x25 mm) - same | 357-BGA (25x25 mm) - same | 357-BGA (25x25 mm) - same |
| Core Architecture | Power Architecture, 32-bit | Power Architecture, 32-bit | Power Architecture, 32-bit | Power Architecture, 32-bit |
| Core Frequency | 133 MHz | 133 MHz | 133 MHz | 66 MHz (-50%) |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Fast Ethernet Controllers | 3 | 3 | Different count - verify | 2 |
| Process Technology | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS | 0.25 µm CMOS |
| Operating Temperature | 0 °C to +95 °C | 0 °C to +95 °C | 0 °C to +95 °C | 0 °C to +95 °C |
主要差異化特點
- Integrated 4-SCC + 2-SMC + SPI + I²C communications engine on die (對比MPC855TVR66D4)
- Three on-chip Fast Ethernet MACs (對比MPC855TVR66D4)
- 0.18 µm CMOS process for lower active power vs 0.25 µm predecessor (對比MPC855TVR66D4)
- Integrated PCI interface (對比MPC850 family without PCI)
設計說明
The 357-BGA at 25 × 25 mm has a ball pitch typically under 1.0 mm; breakout routing requires a multilayer PCB (8 or more layers recommended) with microvia or laser-drilled blind-via technology. Place at least one 0.1 µF X7R decoupling capacitor within 50 mils of every supply ball pair, and a bulk 10 µF tantalum or polymer capacitor near the package's supply ring.
Estimated: at 3.3 V supply, 133 MHz core, and typical 1.5-2 W active power draw, the 357-BGA on a 4-layer board with moderate copper pour holds junction rise under 30 °C above ambient. If the design runs the CPM at full utilization with all four SCCs and three Ethernet MACs active simultaneously, power may climb to 2.5-3 W; add a copper spreader or attach a small stamped heatsink to the lid.
Do not assume the MPC859PVR133A and MPC859TVR133A (or MPC859PZP133A) are interchangeable - the part-number suffix encodes both feature-set and revision differences. The Mouser listing flags the standard PVR133A as 'NO-PB' (non-RoHS leaded finish); if your build requires RoHS, order the explicit Pb-Free suffix variant and verify against the manufacturer's material declaration.
Route the SDRAM interface (address/command in one group, data in a matched-length group) to keep skew under 50 ps. Place the 50 MHz system clock oscillator within 200 mils of the CLK pin with a continuous ground reference plane below; avoid routing the clock trace over any split-plane gaps to prevent jitter and false edges on Reset Configuration.
合規資訊
Mouser listing classifies the standard MPC859PVR133A as 'NO-PB' (non-RoHS leaded BGA finish). Order the Pb-Free suffix variant for RoHS-compliant builds. AEC-Q100 qualification not applicable for this commercial MPU.
