Interface ICs
ژێرپۆلەکان
بەرهەمەکان (560+)
MAX232IDWRE4 - Dual RS-232 Transceiver | Texas Instruments
Texas Instruments MAX232IDWRE4 is a dual EIA-232 driver and receiver for converting TTL/CMOS logic levels to RS-232 signals. It operates from a single 5 V supply, supports data rates up to 120 kbit/s, accepts input voltages of ±30 V, and is packaged in a 16-pin SOIC. The device includes two transmit channels, two receive channels, and an on-chip charge-pump circuit for ±5 V RS-232 signal generation. An RS-232 transceiver is an interface IC that bridges the logic-voltage domain of a digital system and the voltage-domain requirements of an RS-232 port. Within the interface hierarchy, it belongs to the RS-232 transceiver class, which includes drivers, receivers, and combined transceivers. This combined architecture allows one package to support bidirectional serial communication while minimizing the number of components required at each port. The MAX232IDWRE4 operates from one 5 V supply and uses 1.0 µF charge-pump capacitors to generate the bipolar voltages required for RS-232 transmission. Its dual-driver and dual-receiver organization supports two RS-232 channels in one package. The interface can operate at rates up to 120 kbit/s, while ±30 V input tolerance improves robustness when a connected port encounters high-voltage signals. Typical supply current is approximately 8 mA. The internal charge-pump design eliminates the need for a separate negative supply. Nevertheless, charge-pump operation can couple switching energy into adjacent circuitry, making careful capacitor placement and grounding essential. The MAX232 family is designed for legacy RS-232 equipment, industrial control interfaces, service equipment, and other systems that exchange serial commands over long or electrically noisy connections. Typical uses include RS-232 adapters for embedded controllers, configuration and programming ports, industrial diagnostic equipment, and communication links between a host computer and peripheral controller. The 16-pin SOIC package supports conventional surface-mount assembly. Two MAX232IDWRE4 devices can provide four RS-232 channels when one transmitter and one receiver section are used for each full-duplex channel. Place the charge-pump capacitors directly across their designated package pins and connect the device ground to the interface ground using a short return path. Keep sensitive analog or high-speed digital traces away from the charge-pump nodes. Confirm that the selected series capacitors and cables meet the voltage and bandwidth requirements of the connected RS-232 system before production release. This product guide combines interface specifications, pin-level implementation guidance, application selection criteria, and verified drop-in alternatives. It is designed to help engineers confirm electrical compatibility, simplify PCB reuse, and identify the correct replacement before approving a design.
MAX3070EASD+T - 3.3V RS-485/422 Transceiver | Maxim
The Maxim Integrated MAX3070EASD+T is a 3.3 V RS-485/RS-422 interface transceiver with one driver and one receiver, ±15 kV ESD protection, fail-safe receiver behavior, and hot-swap capability in a 14-pin SOIC package. It is designed for industrial communication links that require both differential signaling and protection against electrostatic discharge encountered during installation or maintenance. An RS-485/RS-422 transceiver is an interface IC that converts between logic-level signals and balanced differential bus signals. RS-485 supports multipoint, half-duplex communication over longer industrial distances, while RS-422 commonly supports point-to-point, full-duplex links. The MAX3070EASD+T family combines one transmit driver and one receive channel, allowing a compact interface for systems that need both directions of differential data transfer. The MAX3070EASD+T operates from a 3.3 V supply and provides ±15 kV ESD-protected bus pins. Its fail-safe receiver circuitry guarantees a logic-high output when the receiver inputs are open or shorted. This behavior helps a system interpret an inactive, faulted, or unconnected bus deterministically. The hot-swap feature supports connection of the transceiver to an active bus without the normal startup disturbance associated with an unpowered driver. Internally, the device integrates an RS-485/422-compatible line driver, differential receiver, fail-safe receiver logic, and hot-swap protection into a single 14-pin surface-mount package. The manufacturer describes the MAX3070E through MAX3079E family as 3.3 V, ±15 kV ESD-protected transceivers. A digital transceiver is distinct from an RF transceiver: its principal function is robust conversion of digital logic levels to and from balanced wired-interface signals. Typical uses include industrial sensor networks, factory automation equipment, building-control systems, data acquisition units, and communication links between distributed controllers and field devices. The fail-safe receiver is particularly useful where cables can be disconnected or where a system must maintain a predictable state during reconnection. The ±15 kV protection rating is particularly relevant to industrial environments in which exposed cabling and maintenance practices increase ESD risk. For implementation, place the transceiver close to the connector or board edge so that the protected bus traces are short, and route the balanced differential pair as a tightly coupled pair. Decoupling capacitors should be positioned close to the supply and ground pins. External termination, biasing, and protection components must be selected from the actual cable length, topology, and grounding arrangement rather than added indiscriminately. This product page combines the manufacturer's electrical and protection details with package information, application guidance, drop-in alternatives, and practical bus-layout considerations. Use the MAX3070E-MAX3079E datasheet for the authoritative pin descriptions, absolute maximum ratings, timing characteristics, and recommended external circuitry before completing a production design.
MAX3095EEE+T - 10 Mbps Quad RS-485 Receiver | Analog Devices
The Analog Devices MAX3095EEE+T is a rugged, low-power, quad RS-422/RS-485 receiver with electrostatic discharge protection, 10 Mbps data-rate capability, and a 16-pin QSOP package. The MAX3095 family is designed for level translation and receiver applications where long cable runs, industrial noise, or exposed connector interfaces require enhanced input protection. According to the manufacturer data sheet, receiver inputs are protected to ±15 kV using the IEC 1000-4-2 air-gap discharge method, ±8 kV using the IEC 1000-4-2 contact-discharge method, and ±15 kV using the Human Body Model. An RS-485 receiver is part of the differential digital communications hierarchy: RS-485 bus -> differential line receiver -> interface IC -> embedded system. It converts differential voltage signals on a balanced pair of conductors into a logic-level output for a microcontroller, programmable logic controller, industrial controller, or telecommunications equipment. The MAX3095 contains four independent receivers, allowing one package to serve multiple buses or separate communication channels while reducing board area and external circuitry. The MAX3095EEE+T supports operation from a 5 V supply and is specified for 10 Mbps operation. Its quad-receiver architecture is useful in industrial automation, telecommunications, instrumentation, and embedded control systems where several robust differential inputs are required. The integrated ESD protection reduces the need for separate discrete protection networks close to external connectors, while the space-saving QSOP package supports high-density PCB layouts. The manufacturer lists the MAX3095 and MAX3096 as pin-compatible, low-power upgrades to the industry-standard 26LS32. The MAX3095 and MAX3096 are related by supply voltage: the MAX3095 operates from 5 V, while the MAX3096 family is intended for a lower-voltage operation. Both families provide four RS-422/RS-485 receivers with rugged ESD protection for harsh environments. The MAX3095/MAX3096 family is also used for level translation, ESD-sensitive receiver applications, and telecommunications equipment, providing a practical combination of low power, compact packaging, and protection. For new layouts, place the receiver inputs and the associated protection or connector interface as close as practical to the device, while keeping the logic-side outputs away from high-current switching paths. Verify the board's ground-return arrangement and cable termination strategy because receiver ESD protection does not replace correct bus topology. The data-sheet pin description should be used when assigning PCB tracks, and the receiver enable or enable-control behavior should be checked against the system requirements before final schematic release. This page summarizes the MAX3095EEE+T electrical role, package constraints, protection ratings, and replacement considerations with practical guidance for industrial communications designs. It is intended to help engineers identify whether the receiver belongs in a new RS-485 interface and how to evaluate a same-footprint substitution without overlooking supply voltage, temperature range, or data-rate requirements.
MAX310EPE+ - 8:1 CMOS RF Video Multiplexer | Analog Devices
Analog Devices MAX310EPE+ is an 8-channel, 8:1 CMOS RF and video multiplexer packaged in a 16-pin PDIP package. The device selects one of eight video inputs and routes it to a common output, providing a practical interface for RF and video routing systems. Its production status, single-channel multiplexing architecture, and through-hole PDIP package make it suitable for established analog and video equipment designs. A video multiplexer is an interface IC that connects multiple signal sources to one destination while allowing a controller to select the active channel. The MAX310 family belongs to the broader switching and multiplexing hierarchy, where analog switches and multiplexers route RF, video, or instrumentation signals without requiring duplicated receiver chains. The MAX310EPE+ uses CMOS circuitry and provides eight selectable inputs rather than acting as a general-purpose logic switch. The main defining characteristics are its 8:1 multiplexing ratio, eight channels, CMOS implementation, and 16-pin PDIP package. The unbuffered architecture listed for this device is suitable for routing applications where impedance matching, gain, and signal-level compatibility are handled by the surrounding circuit. It is particularly relevant to video routing, RF signal selection, test and measurement systems, and legacy video equipment that uses through-hole construction. Because the MAX310EPE+ is designed around an analog switching function, system performance depends on the source impedance, load impedance, signal amplitude, selected channel, and frequency being routed. The device should be evaluated in the complete signal path rather than by switching state alone. PCB routing, grounding, connector geometry, and control-signal timing can materially affect isolation, insertion loss, crosstalk, and signal integrity in high-frequency video systems. Typical uses include video-source selection in test equipment, routing among multiple RF channels in instrumentation, channel selection in professional video equipment, and embedded analog switching systems. For new designs, engineers should confirm the supported signal frequency, on-resistance, bandwidth, off-isolation, and supply requirements against the current manufacturer datasheet before fixing the board architecture. Designers should preserve the manufacturer's recommended supply decoupling and provide a low-impedance ground reference close to the device. Control inputs should be driven cleanly and sequenced so that channel changes do not create transient disturbances on sensitive downstream circuitry. Keep analog routing paths short, isolate switching return currents from precision references, and test all channels across the intended operating range. This page organizes the MAX310EPE+ product identity, package information, sourcing fields, replacement analysis, application guidance, and engineering selection criteria in one concise reference. It also highlights where engineers must validate frequency, voltage, current, and channel performance in the manufacturer datasheet before releasing a production design.
MAX310MJE - 8:1 CMOS RF/Video Multiplexer | Analog Devices
Analog Devices MAX310MJE is an 8:1 CMOS RF/video multiplexer in a 16-pin CDIP through-hole package. It supports one multiplexed signal channel, operates as an unbuffered analog switch, and has a maximum on-state resistance of 250 ohms. The device is specified for military-temperature operation and uses a 0.300-inch, 7.62 mm pin pitch. An RF/video multiplexer is an analog switch that connects one common signal path to any one of several signal inputs. It belongs to the analog switch hierarchy, which includes multiplexers and demultiplexers, and ultimately falls under interface ICs and semiconductor signal-routing devices. The MAX310MJE consolidates eight selectable sources onto one output, reducing the number of discrete switches and associated routing logic required in video, test, instrumentation, and communications equipment. Key characteristics include an 8:1 configuration, CMOS construction, 16-CDIP mechanical format, through-hole mounting, and maximum on-state resistance of 250 ohms. Its military temperature grade makes it relevant to ruggedized equipment, although the exact operating-temperature limits should be confirmed against the manufacturer datasheet before a production release. The unbuffered architecture places important emphasis on external source and load impedance, signal amplitude, switching time, and off-state isolation. The MAX310MJE uses independent selection and enable controls to route one of eight channels to the common terminal. Because the switch is unbuffered, it does not provide gain, isolation, impedance buffering, or level translation. Designers should therefore evaluate source impedance, receiver capacitance, settling time, insertion loss, off leakage, and crosstalk together. A practical video path benefits from short traces, a stable ground reference, and termination arranged to minimize reflections. Typical uses include RF and video test systems, instrumentation signal routing, communication equipment, broadcast video interfaces, and defense or aerospace electronics. The part can also support channel-selection architectures where a controller chooses among several inputs and a common amplifier or measurement channel processes the selected signal. Its through-hole CDIP package favors systems that favor through-hole assembly, rugged handling, or prototyping over compact surface-mount layouts. The principal design consideration is signal integrity. Keep input and common-path traces short, use a continuous ground plane, and place the multiplexer near the source of unwanted impedance. Avoid long unterminated traces that can amplify reflections and degrade settling behavior. Review break-before-make requirements in the control timing before switching adjacent channels, especially where the upstream circuit must remain undisturbed during transition. This product overview combines the MAX310MJE configuration, package, resistance, temperature-grade information, and application guidance with pin-compatible alternatives and practical routing considerations. It supports faster sourcing and design decisions while keeping electrical verification anchored in the manufacturer datasheet.
MAX311CPE+ - 8-Channel CMOS RF/Video Multiplexer | Maxim Integrated
The Maxim Integrated MAX311CPE+ is an 8-channel CMOS RF/video multiplexer (analog switch IC) supplied in a 16-pin PDIP through-hole package. Maxim's product page lists the MAX311 family in PRODUCTION status, and the '+' ordering code designates the lead-free/RoHS-compliant configuration of the device. Because the MAX311CPE+ is a purely passive CMOS analog multiplexing element, it adds no signal conditioning, no gain and no level shifting - it simply routes one of several RF or video sources to a common output with low insertion loss and minimal crosstalk. An analog multiplexer (also called an analog switch or mux) is a passive semiconductor device that steers a signal path between multiple inputs and a shared output under digital control. Within the signal-chain hierarchy, a multiplexer sits above a basic analog switch and below larger interface and routing ICs, and it belongs to the broader category of interface ICs used to build video routing, matrix and switching systems. Modern video and RF equipment typically replaces the mechanical relay or coax switch of the past with CMOS mux trees like the MAX311 family. Key characteristics of this device include its 8-channel CMOS construction, its operation as a 2:1/4:1-class RF and video routing element, and its ability to handle baseband video and RF signals in the same multiplexed structure. Because the MAX311CPE+ is a through-hole PDIP-16 device, it is easy to prototype on a perfboard or wire into a legacy instrument, and it remains a convenient choice for repair and obsolescence-management work on older professional video and RF test equipment. Architecturally the part uses CMOS transmission-gate switches with break-before-make control logic, so the control inputs can be driven by standard TTL/CMOS logic and the output never connects two sources together during switching. Signal integrity is the key engineering consideration: with on-resistance, off-isolation, bandwidth and crosstalk all specified by Maxim in the manufacturer data sheet, the MAX311CPE+ is best used with source impedances and cable lengths that do not push the switch into its impedance-sensitive region. Typical applications include professional video routing and patch equipment, broadcast and studio monitoring paths, RF instrumentation and test sets, and general-purpose analog signal routing in laboratory or industrial control panels where an 8-way RF/video selector is required. It is also widely used in legacy test and measurement platforms as a service replacement part. When laying out a design around the MAX311CPE+, keep input and output traces short, use a ground plane reference, and place the device close to the signal source to minimise parasitic capacitance on the high-impedance mux node. Confirm the control logic levels and the enable polarity from the manufacturer data sheet before committing to a PCB, because the enable and select decoding arrangement determines how many control lines your host microcontroller must drive.
MAX3221CPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX3221CPWRG4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply at data rates up to 250 kbit/s. It provides one driver and one receiver in a 16-pin TSSOP package with a 4.40 mm body width. The device also includes ±15 kV electrostatic-discharge protection on its RS-232 interfaces. A transceiver converts logic-level signals into RS-232-compatible differential voltage levels and converts received RS-232 levels back into CMOS-compatible logic. Within the broader communications hierarchy, this device is an RS-232 interface transceiver, a line-driver and receiver IC, and ultimately a signal-conditioning device for serial data links. It is intended for equipment-to-equipment and point-to-point serial communication rather than long-distance networking. Key features include a 3 V to 5.5 V operating range, operation at up to 250 kbit/s, low standby current of 1 µA typical, and compatibility with 5 V logic inputs when operated from a 3.3 V supply. The MAX3221 design uses external 0.1 µF charge-pump capacitors, allowing the interface to generate the bipolar voltage required by RS-232 without a separate DC-DC converter. TI identifies the device as interoperable with equivalent single-channel interface transceivers. The device conforms to TIA/EIA-232-F and ITU V.28 signaling requirements. Its transmitter provides the voltage swing required to drive a standard RS-232 receiver, while its receiver recognizes the negative-going voltage used for a valid RS-232 logic mark. The integrated ±15 kV ESD protection improves survivability when cables are connected or disconnected in industrial, instrumentation, and data-acquisition environments. Typical uses include industrial control consoles, test and measurement equipment, instrumentation links, embedded serial ports, and service-port connections between a host and peripheral. Because the MAX3221 provides only one driver and one receiver, two transceivers are normally required for a full-duplex point-to-point link with transmit and receive data flowing simultaneously. When laying out the circuit, place the 0.1 µF charge-pump capacitors close to their associated pins and route the RS-232 driver output and receiver input away from sensitive analog or high-speed digital traces. Confirm that the logic-side supply voltage matches the host interface, and verify the ground connection between both ends of the cable before relying on common-mode rejection. This page combines the device ratings, package information, functional guidance, pin-level design considerations, and available drop-in alternatives to support faster component selection and PCB implementation.
MAX3221ECPWE4 - 250kbps RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3221ECPWE4 is a single-channel RS-232 line driver/receiver with a 250kbps maximum data rate, a 3V to 5.5V supply range, and ±15kV IEC ESD protection. The device is packaged in a 16-pin TSSOP and provides one driver and one receiver for serial-port interfaces. Its dual charge-pump design supports RS-232 signal generation from a single low-voltage supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts received RS-232 levels back into CMOS-compatible logic. In the electronic hierarchy, a transceiver belongs to the interface IC and line-driver/receiver family, where it connects modern digital systems to the voltage, polarity, and noise-immunity characteristics of the RS-232 standard. The MAX3221ECPWE4 is intended for equipment that needs one bidirectional serial channel rather than the multiple channels available from larger transceivers. Key features include a 3V to 5.5V operating range, operation up to 250kbps, and ±15kV IEC ESD protection. The low-voltage supply capability allows the device to operate directly from 3.3V or 5V system rails. A single channel reduces package size and power requirements when a design does not require multiple RS-232 ports. The integrated driver, receiver, and charge-pump circuitry also simplifies the external interface arrangement. The MAX3221ECPWE4 combines one RS-232 driver and one receiver in a 16-terminal TSSOP package. Its receiver converts the incoming differential voltage on the RS-232 line into a CMOS-compatible output, while the driver converts a CMOS-compatible input into the electrical levels required by RS-232. The dual charge-pump circuit generates the positive and negative voltage levels used by the driver. According to the Texas Instruments MAX3221 datasheet, the device supports data rates up to 250kbps. Typical applications include industrial serial interfaces, point-of-sale equipment, instrumentation, data acquisition systems, and embedded systems that require a single RS-232 port. The device is particularly suitable for compact controller boards operating from 3.3V or 5V rails. Because only one channel is included, systems needing several simultaneous RS-232 ports should use a multichannel transceiver instead. When laying out a design, route the driver output and receiver input to their protected connector-side networks and keep sensitive logic traces away from the exposed RS-232 interface. Use the external components and connector arrangement shown in the manufacturer datasheet for charge-pump capacitors and interface protection. Confirm signal levels, grounding, cable length, and ESD requirements at the connector boundary. This product record combines the exact ordering information, package details, electrical highlights, verified alternatives, and application guidance needed to evaluate the MAX3221ECPWE4. The comparison section distinguishes same-family and cross-brand drop-in options, while the design notes focus on signal routing, protection, and practical implementation decisions.
MAX3221EIPWE4 - 250kbps RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3221EIPWE4 is a single-channel RS-232 line driver and receiver operating from 3 V to 5.5 V, with a maximum data rate of 250 kbps in a 16-pin TSSOP package. The device includes a dual charge-pump circuit and provides ±15-kV ESD protection on the serial-port connection pins. Its 500 mV receiver hysteresis improves noise immunity in industrial and equipment environments. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232-compatible levels and converts received RS-232 signals back into logic levels. The MAX3221EIPWE4 belongs to the line-driver and receiver hierarchy within RS-232 interface ICs, combining one driver, one receiver with a dedicated enable input, and the voltage-conversion charge pumps required for single-supply operation. The principal specifications include a 3 V to 5.5 V supply range, 250 kbps maximum data rate, one driver, one receiver, and operation from -40 °C to 85 °C. The E designation provides enhanced electrostatic-discharge protection, while the 16-TSSOP package supports compact surface-mount assemblies. A 500 mV receiver hysteresis helps prevent output chatter when the received signal is close to the decision threshold. The dual charge-pump architecture allows the interface to generate the positive and negative voltage levels required by RS-232 without a negative supply input. Charge-pump capacitors and supply bypass capacitors should be placed close to their associated pins. The serial-port pins receive the enhanced ESD protection, helping improve robustness against electrostatic discharge encountered during exposed cable connections. Typical applications include industrial serial adapters, programmable-logic-controller communication ports, test and measurement equipment, point-of-sale terminals, and embedded control systems that require a single RS-232 channel. The dedicated receiver-enable pin supports local control of receiver output state, which can simplify interface coordination in multi-function equipment. The primary design trade-off is operating speed versus transmission distance. A 250 kbps transceiver is appropriate for moderate-speed serial links, but long cable runs and high data rates require careful baud-rate selection, grounding, shielding, and protection-network design. Confirm the pin functions and charge-pump values in the manufacturer datasheet before finalizing the PCB. This page organizes the manufacturer specifications, sourcing fields, drop-in replacement findings, comparison parameters, and practical RS-232 interface design guidance. It is intended to help engineers evaluate the MAX3221EIPWE4 against same-footprint alternatives while preserving signal integrity and electrostatic-discharge protection requirements.
MAX3221EUE+ - 1/1 RS-232 Transceiver, 3V-5.5V | Analog Devices
The Analog Devices MAX3221EUE+ is a 1-driver, 1-receiver RS-232 transceiver designed for single-supply operation from 3V to 5.5V. It supports data rates up to 235 kbps and combines a receiver, a transmitter, an on-board charge-pump supply, and enhanced electrostatic-discharge protection in a 16-pin TSSOP package. An RS-232 transceiver is the interface circuit between a digital controller and a serial connector. The receiver converts bipolar RS-232 signal levels into CMOS-compatible logic, while the driver converts CMOS logic back into RS-232 levels. The MAX3221EUE+ therefore replaces a collection of discrete level-shifting, protection, and voltage-generation components with one integrated device. Key features include a 1 µA shutdown supply current, automatic shutdown and wake-up behavior, a 3V to 5.5V operating supply range, and 235 kbps maximum signaling rate. The MAX3221E family is also identified as an EIA/TIA-232-F-compatible interface with enhanced ESD protection on the RS-232 pins. These characteristics suit equipment that must conserve power while maintaining a standard serial port. Internally, the device uses Maxim's AutoShutdown approach. When the receiver does not detect a valid signal, the internal supply and drivers can shut down to reduce power consumption; activity on the receiver input restores operation. The charge-pump circuit and external capacitors generate the bipolar voltage needed by the RS-232 driver from a single positive supply. Typical uses include point-of-sale terminals, industrial control panels, instrumentation, data-logging equipment, and embedded systems that expose a legacy RS-232 port. The single driver and single receiver arrangement makes the part appropriate for one-way or two-way links where two driver/receiver pairs would not be needed. When laying out the board, place the charge-pump capacitors close to their designated pins and route the RS-232 connector side through the protected interface pins. Verify the external interface voltage levels before connecting equipment that uses non-±RS-232 signaling, because logic-level UART signals require a separate transceiver. This page consolidates manufacturer specifications, package details, drop-in alternatives, and application guidance to help engineers evaluate the MAX3221EUE+ before integrating it into a new RS-232 design.
MAX3232CDB - 2/2 RS-232 Transceiver 3-5.5V | Texas Instruments
The Texas Instruments MAX3232CDB is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with two drivers and two receivers, housed in a 16-SSOP package. It operates at data rates up to 250 kbit/s, accepts 5 V logic, and provides plus or minus 15 kV ESD protection on the serial-port connection terminals. According to the MAX3232 datasheet information, the device meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 bipolar levels and converts received bipolar signals back into CMOS-compatible logic. The MAX3232CDB sits between an asynchronous communication controller and a serial-port connector, making it part of the interface IC hierarchy: RS-232 transceiver > line driver/receiver > communications interface > semiconductor. This type of circuit is used when a system must communicate over a longer cable or through a noisy connection than a direct TTL or CMOS serial link can support. The principal benefits of the MAX3232CDB are its 3 V to 5.5 V supply range, 250 kbit/s operating speed, low typical supply current of 300 uA, and external-capacitor charge-pump implementation. The device uses 0.1 uF external capacitors, including the charge-pump capacitors and the recommended driver-side capacitor network. Its two-channel transmitter and receiver arrangement supports RS-232 links carrying two data channels while remaining compact in a 16-SSOP footprint. The MAX3232 is based on the classic MAX3232 family, while the MAX3232E is described by Texas Instruments as an improved direct drop-in replacement for the MAX3232. The MAX3232E family can therefore be considered for new designs when its electrical details are verified against the system requirements. The MAX3232IPW is also listed in the site component set as a closely related MAX3232-family choice. Typical applications include industrial serial-port equipment, test and measurement instruments, data acquisition systems, embedded-control consoles, and point-of-sale terminals. The MAX3232CDB is especially useful where a legacy RS-232 port must coexist with a modern low-voltage controller. Its integrated ESD protection improves robustness at the connector side, although cable routing, grounding, and connector selection remain important for reliable operation. For a new design, use the manufacturer datasheet to confirm the exact pin assignments, capacitor connections, and recommended layout. Place the 0.1 uF charge-pump capacitors close to their associated pins, connect the charge-pump capacitor nodes exactly as shown in the datasheet schematic, and keep the RS-232 traces away from sensitive analog or high-speed digital paths. Treat the MAX3232CDB as a legacy RS-232 interface solution rather than a substitute for a modern differential bus such as RS-485. This page combines the verified electrical and package characteristics with application guidance, drop-in alternatives, and practical PCB considerations for engineers evaluating the MAX3232CDB.
MAX3232CDBR - 2/2 RS-232 Transceiver 3-5.5V | Texas Instruments (Tape & Reel)
The Texas Instruments MAX3232CDBR is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with two drivers and two receivers, housed in a 16-SSOP package. It operates at data rates up to 250 kbit/s, accepts 5 V logic, and provides plus or minus 15 kV ESD protection on the serial-port connection terminals. According to the MAX3232 datasheet information, the device meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 bipolar levels and converts received bipolar signals back into CMOS-compatible logic. The MAX3232CDBR sits between an asynchronous communication controller and a serial-port connector, making it part of the interface IC hierarchy: RS-232 transceiver > line driver/receiver > communications interface > semiconductor. This type of circuit is used when a system must communicate over a longer cable or through a noisy connection than a direct TTL or CMOS serial link can support. The principal benefits of the MAX3232CDBR are its 3 V to 5.5 V supply range, 250 kbit/s operating speed, low typical supply current of 300 uA, and external-capacitor charge-pump implementation. The device uses 0.1 uF external capacitors, including the charge-pump capacitors and the recommended driver-side capacitor network. Its two-channel transmitter and receiver arrangement supports RS-232 links carrying two data channels while remaining compact in a 16-SSOP footprint. The MAX3232 is based on the classic MAX3232 family, while the MAX3232E is described by Texas Instruments as an improved direct drop-in replacement for the MAX3232. The MAX3232E family can therefore be considered for new designs when its electrical details are verified against the system requirements. The MAX3232IPW is also listed in the site component set as a closely related MAX3232-family choice. Typical applications include industrial serial-port equipment, test and measurement instruments, data acquisition systems, embedded-control consoles, and point-of-sale terminals. The MAX3232CDBR is especially useful where a legacy RS-232 port must coexist with a modern low-voltage controller. Its integrated ESD protection improves robustness at the connector side, although cable routing, grounding, and connector selection remain important for reliable operation. For a new design, use the manufacturer datasheet to confirm the exact pin assignments, capacitor connections, and recommended layout. Place the 0.1 uF charge-pump capacitors close to their associated pins, connect the charge-pump capacitor nodes exactly as shown in the datasheet schematic, and keep the RS-232 traces away from sensitive analog or high-speed digital paths. Treat the MAX3232CDBR as a legacy RS-232 interface solution rather than a substitute for a modern differential bus such as RS-485. This page combines the verified electrical and package characteristics with application guidance, drop-in alternatives, and practical PCB considerations for engineers evaluating the MAX3232CDBR.
MAX3232CSE+ - 1Mbps Dual RS-232 Transceiver | Maxim
The Maxim Integrated MAX3232CSE+ is a dual, low-power, true RS-232 transceiver rated for operation from 3.0V to 5.5V, data rates up to 1Mbps, and a 16-SOIC package. It integrates two drivers and two receivers with charge-pump voltage conversion for single-supply RS-232 interfaces. The verified distributor information identifies the device as a 2/2 RS-232 transceiver, while Mouser specifies a 3.0V-to-5.5V supply range and operation up to 1Mbps. A true RS-232 transceiver translates logic-level signals between CMOS-compatible systems and the voltage-defined RS-232 interface. Unlike a TTL or CMOS serial interface, RS-232 uses positive and negative signal voltages to represent data. The MAX3232CSE+ uses dual charge pumps and external capacitors to generate the required positive and negative transmitter voltage levels, allowing a single 3.0V-to-5.5V supply to interface with a conventional RS-232 port. The device provides two transmit channels and two receive channels, making it suitable for bidirectional serial links, industrial-control connections, test equipment, and embedded systems that need RS-232 compatibility. Its low-power design is appropriate for portable and embedded equipment, while the 1Mbps capability supports higher-speed serial communication than many legacy RS-232 implementations. The verified data identifies the MAX3232CSE+ as a 16-SOIC device, suitable for surface-mount PCB assembly. The external charge-pump capacitors are central to operation and must be placed close to the relevant pins. Layout, capacitor stability, supply decoupling, grounding, and protection-network design should follow the manufacturer datasheet recommendations. Because the verified excerpts do not provide complete electrical-characteristic tables or exact charge-pump capacitor values, those details should be confirmed from the official manufacturer datasheet before production release. This page consolidates the verified distributor descriptions, package information, pricing reference, and application-oriented design guidance for engineers evaluating the MAX3232CSE+. It also distinguishes verified data from parameters requiring direct confirmation from the manufacturer datasheet, avoiding unsupported specifications.
MAX3232ECAE+T - 15kV ESD RS-232 Transceiver 1Mbps | Analog Devices
The Analog Devices (Maxim Integrated) MAX3232ECAE+T is a ±15kV ESD-protected, 2-driver/2-receiver true RS-232 transceiver operating from a single 3.0V to 5.5V supply, supporting data rates up to 1Mbps in a 16-pin SSOP (CAE) package supplied on tape and reel. It integrates a dual charge-pump circuit that generates ±5.5V RS-232 level swings from a single low-voltage rail, eliminating the need for external negative supplies. An RS-232 transceiver is a line driver/receiver IC that converts logic-level UART signals (0V to 3.3V or 5V) to the voltage levels defined by EIA/TIA-232 and V.28/V.24, and vice versa. Within the signal-chain hierarchy, it sits in the interface IC family between a microcontroller UART and a physical serial-port connector, performing both level translation and electrical isolation of the cable environment. Key features include ±15kV IEC 61000-4-2 air-gap and human-body-model ESD protection on all transmitter outputs and receiver inputs, ultra-low 10nA typical shutdown supply current for battery-powered designs, guaranteed 250kbps minimum data rate under worst-case loading (up to 1Mbps typical in driver-load configurations), and the industry-standard MAX232-compatible pinout for drop-in upgrades of legacy designs. Logic-compatible receiver outputs make direct connection to 3V and 5V MCUs possible. The device uses Maxim's proprietary charge-pump architecture with four small external 0.1uF capacitors to produce the required RS-232 levels, reducing board area and component count. Enhanced ESD structures protect the serial-port connection pins including GND, a critical advantage for cables exposed to human handling in industrial field environments. Typical applications include industrial process-control serial links, point-of-sale terminals, battery-powered portable instruments, and embedded systems that bridge modern MCUs to legacy RS-232 equipment such as PLCs, meters, and modems. The 3.0V operation suits lithium-battery and 3.3V logic designs directly. Design consideration: the CAE temperature grade is 0C to +70C; select the industrial-grade MAX3232EEAE variant for -40C to +85C environments. Charge-pump capacitors must be placed close to the device to minimize supply droop at high data rates. This page adds value beyond the manufacturer datasheet by synthesizing drop-in cross-references (including the MaxLinear SP3232EBCA-L/TR), package and grade comparisons, pricing context, and practical design notes in one place.
MAX3232EEAE+T - 1Mbps RS-232 Transceiver | Analog Devices
The Analog Devices MAX3232EEAE+T is a true RS-232 transceiver containing two line drivers and two line receivers in a 16-pin SSOP package. It operates from a 3.0V to 5.5V supply, supports data rates up to 1Mbps, and provides ESD protection up to ±15kV on the serial-port pins. The integrated dual charge-pump supply generates the bipolar voltage levels required by true RS-232 drivers. A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the transceiver hierarchy within interface ICs and power-management support functions, enabling reliable point-to-point communication between a host controller and an external serial device. The MAX3232EEAE+T combines a 2-driver and 2-receiver configuration, a 1Mbps maximum signaling rate, and low-power operation from 3.0V to 5.5V. Its ±15kV ESD protection helps improve reliability in industrial, instrumentation, and communications equipment where a protected cable or connector may be exposed to electrostatic discharge. The 16-SSOP package also supports compact surface-mount PCB layouts. The device uses an integrated charge-pump architecture to generate the positive and negative voltages required for compliant RS-232 output signaling. Because the charge pumps and drivers operate continuously, power dissipation depends on supply voltage, data activity, load impedance, cable length, and the rate of data transitions. The MAX3232E family is designed to meet TIA/EIA-232-F requirements and provides the electrical interface between asynchronous communication controllers and serial connectors. Typical applications include industrial control consoles, barcode and data-acquisition equipment, test and measurement instruments, point-of-sale terminals, and embedded systems using RS-232 links. The two-driver and two-receiver arrangement suits bidirectional point-to-point communication or split unidirectional links. The 1Mbps capability supports high-speed legacy serial equipment where greater baud rates and shorter-distance signaling are required. Decoupling capacitors must be placed close to the charge-pump and supply pins, while the RS-232 connector-side traces should be routed to minimize noise coupling into sensitive logic. External protection can still be required for long cables or severe industrial environments because the integrated ±15kV rating does not remove the need for suitable enclosure, grounding, and cable design. This product page combines the MAX3232EEAE+T operating characteristics, verified package information, family drop-in options, application guidance, and design considerations to help engineers evaluate the device before integrating a compact, low-power RS-232 interface.
MAX3232EIDW - 250kbps Dual RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3232EIDW is a dual-channel RS-232 line driver/receiver operating from a 3 V to 5.5 V supply, with data signaling rates up to 250 kbps and ±15 kV IEC ESD protection. It is packaged in a 16-pin SOIC for industrial, communications, instrumentation, and legacy serial-port interface applications. An RS-232 transceiver is an interface IC that converts logic-level signals from an asynchronous communication controller into RS-232 line levels and converts received RS-232 signals back into digital logic levels. The MAX3232E combines two line drivers, two line receivers, and a dual charge-pump circuit in one 16-pin SOIC package. Its charge-pump design allows true RS-232 operation from a single 3 V to 5.5 V supply without a separate bipolar supply. Key features include two driver channels, two receiver channels, operation up to 250 kbps, and ±15 kV IEC ESD protection on the serial-port connection pins, including ground. The MAX3232E designation identifies the enhanced ESD-protected family, while the DW suffix denotes the 16-pin SOIC configuration. The 3 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. Technically, the internal charge pumps generate the positive and negative voltage levels required by the RS-232 interface while the drivers and receivers perform level conversion. Charge-pump capacitors and the supply bypass capacitor must be connected according to the manufacturer's recommended application circuit. Adequate trace routing and grounding help preserve signal integrity and reduce radiated emissions at higher data rates. Typical applications include RS-232 links between embedded systems and industrial equipment, PC-compatible serial ports, test and measurement instruments, point-of-sale terminals, and legacy data-acquisition equipment. The dual-channel arrangement allows simultaneous transmit and receive operation across two RS-232 ports when the controller supports two UART channels. For PCB implementation, place the charge-pump capacitors and input bypass capacitor close to their associated pins, keep the interface connector away from sensitive analog circuitry, and provide a stable ground return. Validate the completed design for ESD, emissions, and receiver thresholds if the cable length or system operating environment exceeds the reference conditions used during development. This product page combines manufacturer specifications, interface selection guidance, drop-in alternatives, and practical PCB implementation advice to support RS-232 design and sourcing decisions.
MAX3232EIPWG4 - Dual RS-232 Transceiver 250kbps | TI
The Texas Instruments MAX3232EIPWG4 is a 3-V to 5.5-V multichannel RS-232 line driver/receiver with dual drivers and dual receivers, 250 kbps data rate, and +/-15-kV IEC ESD protection, housed in a 16-pin TSSOP (PW) package rated from -40C to +85C. An RS-232 line driver/receiver is an interface transceiver that converts logic-level UART signals (TTL/CMOS, 0 V to VCC) into the higher-voltage RS-232 signal levels defined by TIA/EIA-232-F (+/-5 V minimum) and back again. It sits in the physical layer of the serial-communication hierarchy - below protocols such as UART framing - and within the broader family of line drivers, bus transceivers, and interface ICs. Because RS-232 levels exceed the supply rail, these devices integrate charge-pump voltage converters that generate the required positive and negative rails from a single low-voltage supply. Key features of the MAX3232E include operation from a single 3.0 V to 5.5 V supply, a proprietary low-dropout transmitter output stage delivering true RS-232 performance from 3.3 V and 5 V rails, dual charge pumps requiring only four small 0.1 uF external capacitors, and 250 kbps minimum data rate. ESD protection is rated at +/-15 kV (IEC 61000-4-2 air-gap), +/-8 kV (IEC 61000-4-2 contact discharge), and +/-15 kV human-body model on the RS-232 bus pins. Architecturally, the device uses two charge-pump stages (voltage doubler and inverter) with external flying and reservoir capacitors to synthesize approximately +/-5.5 V transmitter supplies from the VCC rail. The transmitter outputs meet or exceed TIA/EIA-232-F and ITU V.28 requirements and are protected against unlimited +/-15 V simultaneous shorts, while receivers keep the input threshold compatible with legacy 5 V logic. Typical applications include industrial process-control serial links, point-of-sale terminals and barcode scanners, battery-powered instrumentation using the low 0.3 mA typical supply current, and legacy DB9 COM-port interfacing for microcontrollers such as MSP430 and STM32. When designing, use 0.1 uF charge-pump capacitors placed within 10 mm of the device, and remember the receivers remain active even when transmitters are tri-stated. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet, as of 2026-09-11.
MAX3232IDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3232IDWRE4 is a dual RS-232 line-driver and line-receiver transceiver with two drivers, two receivers, a 3 V to 5.5 V supply range, and a maximum data rate of 250 kbps. The device is packaged in a 16-pin SOIC and is specified for an industrial operating-temperature range of -40°C to 85°C. An RS-232 interface transceiver is an interface IC that converts digital logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level voltages. In the hierarchy of electronic components, this dual transceiver belongs to the RS-232 interface IC family, interface IC category, and broader semiconductor and signal-conditioning product classes. The MAX3232 combines both directions of conversion on one device, reducing the component count in equipment that requires more than one serial communication channel. The MAX3232IDWRE4 operates from 3 V to 5.5 V, supports data rates up to 250 kbps, and integrates two drivers with two receivers. Its 16-SOIC package measures 0.295 inches, or 7.50 mm, in width. The industrial temperature grade supports applications operating from -40°C through 85°C, while its dual architecture suits systems needing two transmit and two receive channels. The device uses charge-pump circuitry to generate the positive and negative voltages required by the RS-232 electrical interface. According to the MAX3232 documentation, the serial-port connection pins provide plus-or-minus 15 kV ESD protection. The circuit also meets the electrical-interface requirements of TIA/EIA-232-F. These features make it appropriate for legacy and industrial serial links where logic-level UART signaling must cross into an RS-232 connection. Typical applications include industrial controller links, programmable-logic-controller serial communication, instrumentation, barcode-scanner interfaces, and legacy computer serial ports. A single MAX3232 can support two RS-232 channels, but each channel still requires the correct external charge-pump capacitors, signal routing, ground reference, and connector protection required by the system interface. The primary design consideration is charge-pump capacitor selection and placement. Use the capacitor values specified by the manufacturer datasheet and place them close to the corresponding IC pins to minimize switching noise and unstable charge-pump behavior. Confirm that the host UART logic levels, baud rate, signal polarity, and RS-232 connector wiring match the target equipment. This product page combines the verified MAX3232IDWRE4 electrical and mechanical characteristics with same-package drop-in alternatives, parameter-by-parameter comparison, application guidance, and practical PCB considerations. It is intended to help engineers identify whether the MAX3232IDWRE4 fits a new RS-232 design or whether a listed replacement offers a better sourcing or lifecycle option.
MAX3243CDB - 250kbps RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX3243CDB is a 3 V to 5.5 V multichannel RS-232 line driver and receiver operating at up to 250 kbps in a 28-pin SSOP package. It integrates three line drivers, five line receivers, and ±15 kV ESD protection using the HBM model. The device is designed for single-supply serial-interface equipment, including DE-9 DTE-style connections, industrial controls, data acquisition systems, and embedded serial ports. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into digital logic. Within the semiconductor hierarchy, it belongs to the interface-controller and transceiver class, where it bridges computer or embedded-system logic and a physical communications port. The MAX3243 integrates bidirectional conversion, ESD protection, and power-management functions into one device, reducing the number of external interface components required. The three drivers support three outbound RS-232 channels, while the five receivers support five inbound channels. This channel imbalance suits a DE-9 DTE interface because transmit, receive, and handshake signals do not use an equal number of conductors. Its operating range of 3 V to 5.5 V also supports both 3.3 V and 5 V system rails, while the 250 kbps maximum signaling rate accommodates legacy serial ports and moderate-speed industrial communication links. The MAX3243 includes flexible automatic power-management features that can reduce supply consumption when unused. It also provides dedicated status outputs, including ROUT2B and INVALID, for monitoring ring indication and valid RS-232 input conditions. Pin-to-pin ESD protection is specified at ±15 kV under the HBM model, helping protect serial-port connections exposed to electrostatic discharge in industrial and desktop equipment. Typical uses include PC-compatible serial ports, point-of-sale terminals, industrial serial controllers, security equipment, instrument interfaces, and embedded systems that exchange data over RS-232. The five receivers are useful when a design needs more incoming status signals than the three driver channels can support, while the dedicated status outputs simplify software-controlled modem and peripheral detection. When implementing the MAX3243CDB, place input and output bypass capacitors close to the supply pins and route protected serial lines away from sensitive analog or high-speed digital traces. Confirm that the connector’s RS-232 voltage levels, ground reference, and signal directions agree with the three-driver, five-receiver configuration. Review the manufacturer pin-description table before assigning every net or connector lead. This page consolidates the device’s operating limits, channel architecture, package details, sourcing guidance, and application-specific engineering guidance into a design-oriented reference for engineers evaluating the MAX3243CDB for compact single-supply RS-232 implementations.
MAX3243CDBRE4 - 250kbps RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX3243CDBRE4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with 250 kbps data-rate capability and ±15 kV ESD protection, housed in a 28-pin SSOP package. It combines three RS-232 drivers, five RS-232 receivers, and an integrated dual charge-pump circuit in one interface IC. An RS-232 transceiver is the electrical bridge between a low-voltage digital controller and a differential, bipolar-voltage communications port. It converts controller-side logic levels into RS-232-compatible driver outputs while converting incoming RS-232 signals into logic-compatible receiver outputs. The MAX3243 belongs to the RS-232 transceiver class within interface ICs, providing signal conditioning, voltage translation, and port protection in a single device. The device operates from 3 V to 5.5 V, supports data rates up to 250 kbps, and provides ±15 kV human-body-model ESD protection. The MAX3243CDBRE4 commercial-temperature ordering option is specified from 0 °C to 70 °C. Its low-power mode and wake-up function support systems where the interface must reduce consumption while still detecting an incoming activity signal. The three-driver and five-receiver arrangement is useful for asymmetric serial links. A system with three outbound command or control signals can share one part with two additional inbound receiver channels. The integrated charge-pump circuit generates the RS-232 bipolar voltage required by the drivers, reducing the need for external charge-pump components while retaining a compact 28-pin SSOP footprint. Typical uses include industrial control systems, test and measurement equipment, data-acquisition systems, instrumentation links, and embedded serial interfaces. The MAX3243 is especially appropriate where several RS-232 channels must share a limited board area and where ESD protection is needed at externally accessible connectors. When laying out the circuit, route the charge-pump capacitor connections and driver outputs according to the manufacturer's application diagram. Keep external protection and connector circuitry away from sensitive logic paths, and verify that the selected cable, grounding method, and logic levels match the intended RS-232 application. This product page organizes the principal electrical limits, package information, application fit, and verified drop-in alternatives. It also highlights practical interface-design considerations that help engineers evaluate the MAX3243CDBRE4 beyond a basic distributor specification summary.
MAX3243CPW - 3-5.5V 250kbps RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX3243CPW is a multichannel RS-232 line driver and receiver with three drivers, five receivers, a 3 V to 5.5 V supply range, and operation up to 250 kbps in a 28-pin TSSOP package. The device also provides ±15 kV ESD protection using the HBM model on serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. Within the interface hierarchy, the MAX3243CPW combines a line driver, line receiver, and charge-pump-assisted level-shifting functions. Its three-driver, five-receiver arrangement is particularly useful for DE-9-style data terminal equipment interfaces that need more receiver channels than transmitter channels. The MAX3243 offers flexible power features that can reduce consumption automatically, helping equipment designers limit power use when communication activity is low. Two always-enabled outputs, ROUT2B and INVALID, support checking a ring indicator and determining whether received RS-232 data is valid. The 3 V to 5.5 V operating range allows the same interface circuit to operate from either 3.3 V or 5 V system rails. Operation at up to 250 kbps makes the device suitable for moderate-speed serial data links rather than only slow legacy port traffic. Its ±15 kV HBM ESD protection adds system-level ruggedness at externally accessible RS-232 connectors, where cables and user equipment can introduce electrostatic discharge. Protection ratings should still be complemented by appropriate board-level grounding and cable-routing practices. Typical uses include industrial serial consoles, data acquisition equipment, test and measurement instruments, embedded control systems, and legacy peripheral interfaces. The five receivers are useful when a system must monitor several RS-232 inputs, such as modem-control, status, ring, and data signals, while three drivers can handle transmit and control lines. PCB design should reserve the 28-pin TSSOP footprint, connect all supply and ground pins as directed by the manufacturer, place charge-pump capacitors close to their associated pins, and route RS-232 connector traces away from sensitive logic. Confirm signal direction, receiver enable, shutdown, and always-enabled output behavior against the manufacturer pin description before finalizing the schematic. This product guide consolidates the principal electrical ratings, package information, interface use cases, verified cross-references, and practical layout considerations into an engineer-focused reference for selecting and implementing the MAX3243CPW.
MAX3243CPWRE4 - 3:5 RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX3243CPWRE4 is a 3:5 multichannel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply. It supports data rates up to 250 kbps, provides three driver and five receiver channels, and includes plus or minus 15 kV human-body-model ESD protection on the interface pins. The device is offered in a 28-pin TSSOP package. A multichannel RS-232 transceiver is an interface IC that combines the electrical drivers and receivers required to connect a low-voltage digital system to an RS-232 port. Within the interface hierarchy, it is both a line transceiver and a multichannel RS-232 interface IC. Its mixed driver-and-receiver arrangement supports equipment designs that need more receive channels than transmit channels, such as data acquisition, industrial control, test equipment, and multiport communications systems. Key features include a 3 V to 5.5 V operating range, 250 kbps maximum signaling rate, three drivers, five receivers, and plus or minus 15 kV ESD protection rated to the human-body-model test method. The 28-pin TSSOP package provides a compact surface-mount footprint, while its gull-wing terminal arrangement supports automated assembly and conventional PCB routing. The MAX3243 family uses charge-pump-assisted interface circuitry to generate the RS-232 bipolar voltage levels required by the standard. This allows the host-side logic to operate from a single 3 V or 5 V supply rather than requiring a separate negative rail for the RS-232 drivers. The transmitter handles the voltage translation and signal shaping, while the receiver converts the bipolar RS-232 input into a logic-compatible signal. Typical uses include industrial serial controllers, programmable-logic-interface equipment, data loggers, point-of-sale terminals, test-and-measurement instruments, and embedded systems that connect a TTL or CMOS serial port to an RS-232 bus. The five receiver channels also make the device suitable for monitoring multiple inbound RS-232 signals, including modem-control or status lines. The obsolete ordering code MAX3243CPWRE4 should not be used for new production releases without confirming an authorized supply route. For new designs, select the currently supported ordering option from the MAX3243 family and confirm the commercial temperature requirement, package fit, and availability before layout release. This page consolidates the manufacturer device description, lifecycle information, package details, interface characteristics, and verified cross-reference findings. It also provides engineering guidance on supply-voltage design, ESD protection, logic compatibility, and the practical differences between current family members and the obsolete original ordering code.
MAX3243ECAI+TG1Z - 3V RS-232 Transceiver | Analog Devices
Analog Devices MAX3243ECAI+TG1Z is a 3-driver, 5-receiver RS-232 interface transceiver designed for 3V-powered serial communications. The device operates from 3.0V to 5.5V, supports data rates up to 120 kbit/s, and is housed in a 28-pin SSOP package. Its AutoShutdown feature reduces supply current to 1 µA when no valid receiver signal is present, while enhanced electrostatic-discharge protection helps protect ports exposed to cable transients. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the line-driver and line-receiver hierarchy, connecting UART, microprocessor, or industrial-control logic to a cable-based serial port. The MAX3243 family is particularly useful when a design requires more than the standard two-transmitter, two-receiver arrangement and also needs low-power standby operation. Key features include three active drivers, five receivers, and one always-active receiver intended for external monitoring. The 3.0V to 5.5V supply range supports both 3.3V and 5V systems. Automatic shutdown and wakeup reduce power when the connected equipment is inactive, while the always-active receiver permits monitoring without keeping the main transmitter circuitry powered. The 120 kbit/s data rate covers legacy RS-232 equipment and industrial serial links. The MAX3243 uses charge-pump circuitry to generate the bipolar voltage levels required by RS-232 while operating from a single low-voltage supply. Its enhanced ESD protection is intended for interfaces connected to external cables, where electrostatic discharge and switching transients are more likely than on internal logic nets. Because the interface is not a differential communications standard, cable length, grounding, termination, and data direction must be considered during system integration. Typical uses include industrial control consoles, laboratory equipment, POS terminals, printers, data-acquisition systems, and service interfaces. The five-receiver arrangement can support several incoming RS-232 connections, while the three drivers support outgoing channels. The always-active monitoring receiver is useful in systems that must detect a remote or peripheral status signal even when automatic shutdown has disabled the normal receiver bank. Place the device close to the connector and route the exposed driver and receiver pins directly to the protected interface boundary. Keep logic-side traces away from cable-side pins, provide a stable ground reference, and follow the manufacturer application guidance for bypass capacitors and charge-pump capacitors. Verify signal polarity, direction, and shutdown behavior in firmware because these details determine how the transceiver should be enabled during communication. This product page combines the manufacturer family description with package-specific identification, practical interface design guidance, selection criteria, and a verified list of drop-in alternatives. It is intended to help engineers confirm supply compatibility, understand receiver and driver assignments, and determine whether the MAX3243 feature set fits a particular RS-232 design before layout release.
MAX3243ECPWG4 - 3/5 RS-232 Transceiver 28-TSSOP | Texas Instruments
Texas Instruments MAX3243ECPWG4 is a 3-to-5.5-V multichannel RS-232 line driver/receiver with 3 drivers, 5 receivers, and ±15-kV IEC ESD protection in a 28-pin TSSOP package. The device is designed for equipment that needs multiple RS-232 ports while operating from a single 3-V or 5-V supply. Its listed data rate is 500 kbps, and the operating temperature grade is commercial, 0°C to 70°C. An RS-232 transceiver combines the electrical interface functions required by a serial communications port. The driver section translates digital logic levels into RS-232 line signals, while the receiver section converts incoming line signals into logic-compatible outputs. A multichannel device such as the MAX3243ECPWG4 supports three driver channels and five receiver channels, allowing a system to implement several serial links without using separate single-channel transceivers. The family is commonly positioned for point-to-point RS-232 equipment, industrial control interfaces, and legacy peripheral connections. The MAX3243E family supports supply voltages from 3 V to 5.5 V, making it suitable for systems with 3.3-V or 5-V digital rails. The device includes ±15-kV IEC ESD protection on its external RS-232 connections, helping protect interface circuitry when cables are connected to user-accessible equipment. The MAX3243ECPWG4 is specified in a 28-TSSOP package with a 4.40-mm body width, and the commercial temperature range covers 0°C to 70°C. Use the manufacturer datasheet and package drawing to confirm the exact pin functions, exposed-pad arrangement, decoupling requirements, and recommended external charge-pump capacitors. The MAX3243E family operates as a multichannel RS-232 interface rather than as a voltage regulator or logic IC, so its power, ground, and signal connections should follow the device-specific application circuit. Request a quote through the XAIPART Request a Quote form for current commercial sourcing information. This page summarizes the device's RS-232 interface role, key electrical ratings, package information, and practical design considerations. It also distinguishes the obsolete MAX3243ECPWG4 ordering code from available family members and drop-in candidates, helping engineers make a controlled replacement decision rather than relying on package similarity alone.