Interface ICs
ژێرپۆلەکان
بەرهەمەکان (560+)
MAX3243ECPWR - 3/5 RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3243ECPWR is a 3/5 multichannel RS-232 line driver and receiver operating from 3 V to 5.5 V, supporting data rates up to 500 kbps in a 28-pin TSSOP package. The device integrates three drivers, five receivers, and a dual charge-pump circuit that generates the positive and negative voltage levels required by RS-232 links. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or embedded controller and the bipolar, positive and negative signal domain used by serial ports. Within the interface hierarchy, it belongs to the RS-232 transceiver and multi-channel line-driver/receiver family, providing the physical interface between an asynchronous communication controller and a connected data terminal or data communications equipment. The MAX3243ECPWR provides TIA/EIA-232-F compliant operation, allowing it to interface with conventional RS-232 ports while operating from a modern 3 V or 5 V supply. Its ±15 kV human-body-model and air-gap discharge protection ratings strengthen the serial connector path against electrostatic discharge. The protected serial-port pins also support ±8 kV IEC 61000-4-2 contact-discharge protection. The integrated dual charge-pump circuit supports both transmitter and receiver operation without a separate external negative supply. Internal voltage conversion produces the bipolar levels required for RS-232 signaling while keeping the system power architecture simple. The three transmitters support connection to multiple data channels, while the five receivers can monitor additional lines such as modem-control or status signals. Typical applications include industrial serial gateways, point-of-sale equipment, test instruments, industrial control panels, and embedded systems that require RS-232 compatibility with 3 V or 5 V logic. The five-receiver arrangement is useful in designs where the host must inspect handshake, control, or status lines in addition to transmitting on one or more data channels. The device is also appropriate for legacy peripheral connections that predate universal serial bus. PCB design should place charge-pump capacitors close to their associated pins, provide a continuous ground return for every transceiver connection, and route exposed serial traces away from sensitive analog circuitry. Input and logic-side decoupling should follow the capacitor guidance in the manufacturer datasheet. Connector protection may still be required when cables extend beyond the enclosure or connect to unknown external equipment. This page combines the MAX3243ECPWR interface capabilities, verified package information, engineering alternatives, and practical RS-232 implementation guidance to help designers evaluate footprint compatibility, protection requirements, and multichannel interface needs before circuit-board release.
MAX3243EEAI+TG1Z - 3.0V RS-232 Transceiver | Analog Devices
Analog Devices MAX3243EEAI+TG1Z is a 3/5-driver, 5-receiver RS-232 transceiver designed for 3.0V to 5.5V operation. It supports data rates up to 250 kbps and includes enhanced electrostatic-discharge protection of ±15 kV, automatic shutdown, and wake-up functionality. The device is packaged in a 28-pin SSOP, making it suitable for space-constrained equipment where a single compact IC must provide both transmit and receive channels. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into logic-level signals. The MAX3243E family combines multiple driver and receiver channels with low-power management features, allowing a system to reduce current consumption when the communication port is inactive. Its automatic shutdown and wake-up behavior helps simplify firmware and power-management design in portable and industrial equipment. Key features of the MAX3243EEAI+TG1Z include 250 kbps maximum data rate, 3.0V to 5.5V supply operation, ±15 kV ESD protection on the RS-232 lines, and a low-power shutdown mode with a typical shutdown supply current of 1 uA as identified by the distributor product listing. The 28-SSOP package provides a conventional surface-mount footprint for RS-232 ports in instruments, computers, industrial controllers, and communication equipment. The MAX3243EEAI+TG1Z is appropriate when a system needs multiple RS-232 channels but does not require the newer MAX3243EEUI+T variant's alternative package or temperature/qualification positioning. The transmitter outputs include slew-rate control for reduced electromagnetic interference, while the receivers are designed to tolerate RS-232 signal levels encountered in industrial environments. Designers should confirm the exact pin arrangement and signal names in the manufacturer datasheet before finalizing a PCB footprint. Common applications include industrial serial-port equipment, test and measurement instruments, data-collection systems, point-of-sale terminals, and embedded serial controllers. In each case, the device can operate directly from a 3.3V or 5V system rail while maintaining compatibility with external RS-232 equipment. The ±15 kV ESD rating adds useful protection for exposed connector paths, although external protection and layout practices remain important. For new layouts, place the transceiver close to the RS-232 connector, route each signal to its intended driver or receiver pin, and keep high-voltage RS-232 traces away from sensitive analog and high-speed digital circuitry. Decoupling capacitors should be placed near the supply pins, and the unused input pins should be tied to a defined logic level according to the datasheet. This page combines manufacturer product information, distributor listings, package guidance, replacement options, and design-focused selection criteria for engineers evaluating this RS-232 interface device.
MAX3243EEUI+T - 250kbps 3/5 RS-232 Transceiver | Analog Devices
The Analog Devices MAX3243EEUI+T is a 3-driver, 5-receiver full-duplex RS-232 transceiver operating from a 3.0V to 5.5V supply at up to 250kbps, with ±15kV ESD protection and a 28-pin TSSOP package. The device integrates Maxim AutoShutdown technology, allowing the transmitter supply and internal circuitry to shut down when no valid receiver signal is detected. Its receiver set includes a complementary always-active receiver for external monitoring. An RS-232 transceiver is an interface IC that converts between digital logic-level signals and differential, bipolar RS-232 line signals. The MAX3243 belongs to the RS-232 interface hierarchy, combining line drivers, line receivers, charge-pump voltage conversion, and automatic power management in one package. It is used to connect UART, microcontroller, industrial-control, and data-processing systems to legacy serial ports through a ±15kV-protected communications interface. Key features include a 3.0V to 5.5V operating supply, 250kbps maximum data rate, three RS-232 drivers, five RS-232 receivers, and low 1µA shutdown supply current. The ±15kV ESD protection improves robustness when cables are connected or disconnected near exposed equipment. AutoShutdown and AutoShutdown Plus operation reduce supply current when the connected system is inactive, while the always-active receiver allows monitoring even when the main supply has shut down. The MAX3243E family uses an internal charge-pump circuit to generate the positive and negative voltages required by RS-232 transmitters. This architecture lets a 3.0V to 5.5V system communicate with conventional RS-232 equipment without a separate negative supply. The MAX3243EEUI+T is specified for a -40°C to +85°C temperature range and is packaged in a 28-pin TSSOP for surface-mount industrial and embedded equipment. Typical applications include industrial serial consoles, instrumentation interfaces, point-of-sale equipment, telecom systems, embedded control modules, and peripheral connectivity. In each case, the transceiver provides the electrical conversion and signal protection needed between a low-voltage digital controller and an RS-232 port. Designers should verify the required baud rate, cable length, connector protection, supply sequencing, and charge-pump capacitor placement against the manufacturer’s recommended application circuit. For a robust design, place the charge-pump and supply-bypass capacitors close to their associated pins, route the RS-232 driver outputs and receiver inputs away from sensitive digital signals, and provide appropriate chassis grounding at the connector. The integrated ±15kV ESD protection does not replace external surge and lightning protection for long or unprotected cables. This page also organizes package, replacement, and application guidance to support faster engineering selection.
MAX3243EEWI+T - 3/5 RS-232 Transceiver | Analog Devices
Analog Devices MAX3243EEWI+T is a 3-driver, 5-receiver RS-232 transceiver rated for 250 kbps operation, 3.0 V to 5.5 V supply operation, and ±15 kV ESD protection. The device is packaged in a 28-pin wide SOIC and is configured for a full RS-232 communications interface. An RS-232 transceiver is an interface IC that combines differential line drivers and receivers for point-to-point serial communication. It translates host logic levels into RS-232 signal levels and converts received RS-232 signals back into digital levels. Within the interface hierarchy, the MAX3243E belongs to the RS-232 transceiver family of interface ICs, supporting industrial control, embedded systems, and communications equipment. Three driver channels support simultaneous transmit functions, while five receiver channels support multiple incoming signals. Automatic shutdown and wakeup reduce supply consumption when the connected equipment is inactive. The MAX3243 family also supports a low-power operating mode, making it useful where a permanently connected serial interface must minimize standby demand. The wide 3.0 V to 5.5 V supply range accommodates both 3.3 V and 5 V system rails. Enhanced electrostatic discharge protection on the interface pins helps improve robustness against cable-connected transients. The 250 kbps capability is suitable for moderate-speed data links, including configuration interfaces, service ports, and embedded serial connections. Typical applications include industrial control systems, point-of-sale terminals, medical instrumentation, test equipment, and embedded processors requiring a longer RS-232 reach than an unbuffered UART can provide. The automatic shutdown feature is particularly valuable in portable or intermittently connected equipment where reducing inactive current improves overall energy efficiency. Place the device close to the connector and route each RS-232 signal as a short differential pair. Keep logic-side traces away from cable-side pins to minimize coupling. Confirm that the external charge-pump capacitors and logic-level rails meet the circuit requirements in the MAX3243E datasheet before releasing the PCB. This product page combines the manufacturer's device information, package and ordering details, cross-reference findings, and practical interface-layout guidance to support component selection and board-level implementation.
MAX3243EIDB - 3-to-5.5V 500kbps RS-232 | Texas Instruments
The Texas Instruments MAX3243EIDB is a 3-to-5.5V multichannel RS-232 line driver and receiver IC with a 500kbps maximum data rate and three drivers, five receivers, and ±15kV IEC ESD protection. It is housed in a 28-pin SSOP package, with the MAX3243EIDB ordering code identifying the tube-packed industrial-device configuration. An RS-232 transceiver is an interface IC that combines voltage-level drivers and receivers on one chip. RS-232 uses single-ended bipolar signaling, so the drivers convert low-voltage logic into RS-232 levels while the receivers translate incoming RS-232 signals back into logic levels. Within the interface hierarchy, the MAX3243EIDB belongs to the RS-232 transceiver class and supports bidirectional data exchange over a multiwire serial connection. The device provides three line drivers and five line receivers, making it suitable for interfaces that need more receiver channels than transmitter channels. Its maximum signaling rate is 500kbps, while its 3-to-5.5V supply range permits operation from both 3.3V and 5V system rails. The manufacturer also identifies ±15kV IEC ESD protection, adding a defined level of protection for exposed serial-interface connectors. The MAX3243 family uses flexible power features to reduce consumption when communication is not required. The MAX3243 product family also provides special outputs ROUT2B and INVALID, allowing a system to monitor ring-indicator and valid-input status. These functions can simplify termination of modem and communications equipment without requiring additional discrete logic. Typical uses include DB9-style serial ports, industrial data acquisition, service-console interfaces, point-of-sale equipment, and embedded systems that exchange RS-232 data with peripherals. The combination of three transmit channels, five receive channels, a 500kbps rate, and 3-to-5.5V operation allows one transceiver to manage several RS-232 signals while sharing common interface functions. PCB design should route connector-side signals away from sensitive logic and provide a low-impedance ground return. Place bypass capacitance close to the supply pins and follow the manufacturer's pin and layout guidance when terminating unused driver and receiver inputs. Cable protection requirements should be evaluated separately because the specified ±15kV IEC ESD rating protects the interface against electrostatic discharge rather than every overvoltage condition. This page combines the manufacturer's RS-232 transceiver description with package, protection, ordering, and application guidance. It also organizes replacement considerations, interface comparisons, and practical design notes so engineers can evaluate the MAX3243EIDB against other compatible MAX3243-family devices before finalizing a PCB or BOM.
MAX3243EIDBR - 3-to-5.5V 500kbps RS-232 | Texas Instruments (Tape & Reel)
The Texas Instruments MAX3243EIDBR is a 3-to-5.5V multichannel RS-232 line driver and receiver IC with a 500kbps maximum data rate and three drivers, five receivers, and ±15kV IEC ESD protection. It is housed in a 28-pin SSOP package, with the MAX3243EIDBR ordering code identifying the tube-packed industrial-device configuration. An RS-232 transceiver is an interface IC that combines voltage-level drivers and receivers on one chip. RS-232 uses single-ended bipolar signaling, so the drivers convert low-voltage logic into RS-232 levels while the receivers translate incoming RS-232 signals back into logic levels. Within the interface hierarchy, the MAX3243EIDBR belongs to the RS-232 transceiver class and supports bidirectional data exchange over a multiwire serial connection. The device provides three line drivers and five line receivers, making it suitable for interfaces that need more receiver channels than transmitter channels. Its maximum signaling rate is 500kbps, while its 3-to-5.5V supply range permits operation from both 3.3V and 5V system rails. The manufacturer also identifies ±15kV IEC ESD protection, adding a defined level of protection for exposed serial-interface connectors. The MAX3243 family uses flexible power features to reduce consumption when communication is not required. The MAX3243 product family also provides special outputs ROUT2B and INVALID, allowing a system to monitor ring-indicator and valid-input status. These functions can simplify termination of modem and communications equipment without requiring additional discrete logic. Typical uses include DB9-style serial ports, industrial data acquisition, service-console interfaces, point-of-sale equipment, and embedded systems that exchange RS-232 data with peripherals. The combination of three transmit channels, five receive channels, a 500kbps rate, and 3-to-5.5V operation allows one transceiver to manage several RS-232 signals while sharing common interface functions. PCB design should route connector-side signals away from sensitive logic and provide a low-impedance ground return. Place bypass capacitance close to the supply pins and follow the manufacturer's pin and layout guidance when terminating unused driver and receiver inputs. Cable protection requirements should be evaluated separately because the specified ±15kV IEC ESD rating protects the interface against electrostatic discharge rather than every overvoltage condition. This page combines the manufacturer's RS-232 transceiver description with package, protection, ordering, and application guidance. It also organizes replacement considerations, interface comparisons, and practical design notes so engineers can evaluate the MAX3243EIDBR against other compatible MAX3243-family devices before finalizing a PCB or BOM.
MAX3243EIDWRG4 - 3/5 RS-232 Transceiver, 250kbps, 5.5V | Texas Instruments
The Texas Instruments MAX3243EIDWRG4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver with 250 kbps signalling rate and plus or minus 15 kV ESD (HBM) protection, housed in a 28-pin SOIC (DW) package. It integrates three RS-232 drivers and five RS-232 receivers in a single package, making it the workhorse multi-channel transceiver for industrial serial connectivity. An RS-232 transceiver is a type of interface IC that converts logic-level TTL/CMOS signals into RS-232 differential voltage levels and back again. It belongs to the line driver and receiver family, which sits inside interface ICs, which in turn are part of the wider communication and power management semiconductor hierarchy. Because RS-232 uses single-ended bipolar signalling referenced to ground, a transceiver also handles level translation, slew control and, in this case, electrostatic discharge hardening for connector-facing pins. Key features of this device include a 3 V to 5.5 V supply range, a 250 kbps maximum data rate, three transmit channels, five receive channels, on-chip charge pump doubling circuitry with external capacitor pins, and plus or minus 15 kV human-body-model ESD protection. The industrial-temperature grade and gull-wing surface-mount SOIC-28 form factor support long-life industrial and instrumentation equipment. Internally, the driver channels use slew-rate-limited push-pull outputs to limit ringing on long cables, while the receiver channels add hysteresis for noise immunity. The charge-pump and voltage-doubler generate the plus and minus rail voltages required by the RS-232 drivers from a single supply, so no external negative supply is needed. The result is a compact single-chip solution where previously several discrete driver and receiver ICs were required. Typical applications include industrial serial console and terminal servers, point-of-sale terminals and barcode scanners, access-control and surveillance systems, serial instrumentation, and data-logging equipment that must survive industrial ESD environments. When designing with this transceiver, keep the external charge-pump capacitors close to their pins, use a solid ground plane reference for the RS-232 return path, and route connector-side traces away from sensitive analog signals. The 250 kbps rate is normally adequate, but cable length and capacitive loading must be checked against the receiver threshold window. This page consolidates pricing tiers, drop-in replacement options, pin-level detail and practical layout guidance for engineers who need more than the headline parameters on the manufacturer product page.
MAX3243EIPWE4 - 3/5 RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3243EIPWE4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver with three drivers, five receivers, 250 kbps operation, and ±15 kV ESD protection in a 28-pin TSSOP package. It provides the physical-layer interface between RS-232 cable signals and TTL or CMOS-compatible logic used by embedded and industrial equipment. An RS-232 transceiver is an interface IC that converts between single-ended, bipolar RS-232 voltage levels and the lower-voltage logic levels used by digital circuits. The MAX3243 belongs to the broader line-driver and receiver hierarchy, combining three transmit channels with five receive channels in one device. Its multichannel arrangement allows one package to support several serial ports or a mixture of host and peripheral connections while reducing the number of interface components on the PCB. The MAX3243EIPWE4 operates from a 3 V to 5.5 V supply, making it suitable for systems using either 3.3 V or 5 V logic. Its stated maximum data rate of 250 kbps addresses conventional RS-232 links used by embedded controllers, test equipment, industrial controls, and point-of-sale systems. ±15 kV electrostatic-discharge protection helps improve robustness on connector-adjacent circuits where cables can expose equipment to electrostatic discharge. The industrial temperature grade, rectangular gull-wing TSSOP-28 package, and 28 terminals make the device appropriate for leaded-surface-mount industrial assemblies. Operating from a 3 V to 5.5 V supply also allows logic-level sharing with modern microcontrollers and programmable controllers. The three-driver and five-receiver arrangement can conserve board area compared with separate one-channel line-driver and receiver packages when several RS-232 signals must be handled. When designing the interface, connect each driver to the appropriate RS-232 TX and receiver to the RS-232 RX lines, then keep logic-side signals within the supply voltage. Place the required charge-pump capacitors and interface-network components according to the manufacturer datasheet. Route the exposed connector and cable paths away from sensitive logic, and provide the specified ESD-protection network where the transceiver is not adjacent to the connector. For reliable operation, verify that the selected UART supports the required 250 kbps line rate and that the cable length and baud rate satisfy RS-232 practice. Ensure power sequencing does not enable the interface before its logic supply is stable. This page compares the MAX3243EIPWE4 with documented alternatives and summarizes package, channel-count, speed, protection, and supply considerations for faster engineering selection.
MAX3243EIPWRG4 - 3 to 5.5V 500kbps RS-232 Transceiver | Texas Instruments
Texas Instruments MAX3243EIPWRG4 is a multichannel RS-232 line driver and receiver designed for 3 to 5.5 V operation, 500 kbps data rates, and enhanced electrostatic-discharge protection. The device is packaged in a 28-pin TSSOP and is supplied in tape-and-reel packaging for surface-mount assembly. It provides a 500 mV receiver hysteresis according to the manufacturer product information, helping improve noise immunity on unidirectional RS-232 links. The MAX3243E family is suitable for industrial, embedded, and communications equipment requiring multiple serial-driver and receiver channels in one package. An RS-232 transceiver is an interface IC that combines voltage-conversion driver and receiver functions for the RS-232 standard. RS-232 uses single-ended, bipolar signaling in which the logic state at a host or peripheral is translated into a voltage suitable for transmission over a cable. The MAX3243EIPWRG4 belongs to the broader interface-IC hierarchy, combining communication line-driver and line-receiver functions into a surface-mount mixed-signal device. Key features include a 3 to 5.5 V supply range, operation up to 500 kbps, multichannel driver and receiver support, and ±15 kV IEC ESD protection. The 500 kbps capability makes the device useful for moderately high-speed serial links while retaining compatibility with lower-speed RS-232 equipment. Its 500 mV receiver hysteresis provides a defined transition region and improves tolerance of noise present on the receiver input. The MAX3243E architecture is intended for portable and embedded systems where low supply voltage, compactness, and robust serial-interface protection are important. A single device can support several RS-232 channels while reducing the number of separate driver and receiver packages required on the PCB. This integration can simplify routing and conserve board area, although each connected port still requires appropriate signal-line and return-path consideration. Typical applications include industrial control systems, test and measurement equipment, data-acquisition units, point-of-sale terminals, security equipment, and embedded serial-port controllers. The 28-pin TSSOP package is compatible with automated surface-mount assembly, while the 3 V minimum supply allows operation in systems that cannot support a traditional 5 V-only RS-232 interface without level translation. During layout, place the device close to the connector and preserve short, direct paths for each driver and receiver signal. Keep the RS-232 traces away from sensitive analog and high-speed digital nets, and connect the protection and bypass paths using the manufacturer datasheet pin-assignment guidance. Verify the complete pinout and recommended capacitor values before releasing the PCB. This page organizes the key electrical characteristics, package details, application guidance, design notes, and qualified same-package replacement options for engineers evaluating the MAX3243EIPWRG4. It is intended to support design selection and PCB planning without relying on a generic distributor specification summary.
MAX3243EWI+ - 3-5.5V 250kbps RS-232 Transceiver | Analog Devices
The Analog Devices MAX3243EWI+ is a +3V to +5.5V RS-232 transceiver with automatic shutdown and wake-up, operating at up to 250kbps in a 28-pin WSOIC package. It combines three RS-232 drivers and five receivers in one interface, making it suitable for compact serial communication equipment, industrial controls, data acquisition systems, and embedded serial links. The device supports true +3V operation and includes enhanced electrostatic-discharge protection rated at ±15kV according to the manufacturer product information. An RS-232 transceiver is a line-interface IC that converts logic-level signals into RS-232-compatible levels and converts received RS-232 signals back into digital logic levels. In the broader power-management and signal-chain hierarchy, the MAX3243 belongs to the communication-interface IC family, alongside UART transceivers, RS-422 interfaces, and RS-485 transceivers. Its multichannel arrangement reduces the number of separate level-shifting components required in systems with multiple serial ports. Key features include a 3.0V to 5.5V supply range, 250kbps operation, automatic shutdown, and automatic wake-up. The MAX3243 family also provides low supply current in shutdown, with a value of 1uA identified for the MAX3243EWI variant. The enhanced ESD protection helps protect the interface when cables are connected, disconnected, or exposed to electrostatic discharge during industrial and laboratory use. The MAX3243E family is designed for 3V-powered EIA/TIA-232 and V.28/V.24 communications interfaces. The MAX3243EWI+ combines these communication functions with a relatively small 28-pin surface-mount footprint, allowing designers to conserve board area in equipment where multiple serial channels are needed. Its operating approach is especially useful in portable and industrial systems that must reduce power consumption when the serial link is idle. Typical applications include industrial control panels, barcode scanners, test and measurement instruments, security equipment, instrumentation interfaces, and embedded systems that expose an RS-232 port to an external host. In these systems, the transceiver provides the physical-layer level conversion between low-voltage CMOS logic and the RS-232 voltage domain. For PCB implementation, place the transceiver close to the connector and preserve short, appropriately terminated signal routes. Confirm the MAX3243E pin assignments and exposed-pad or package-specific recommendations in the manufacturer datasheet before laying out the board. Input and output protection, cable length, grounding, and the availability of a valid receive signal should be checked together because automatic shutdown depends on valid signal detection.
MAX3243EWI+T - 3.3V/5V 250kbps RS-232 Transceiver | Analog Devices
Analog Devices MAX3243EWI+T is a multichannel RS-232 line-driver and receiver interface IC with three transmit channels, five receive channels, a 3 V to 5.5 V supply range, and data rates up to 250 kbps. The device is offered in a 28-pin SOIC package and provides enhanced electrostatic-discharge protection rated at ±15 kV according to the Texas Instruments product page. An RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic levels. It belongs to the interface-IC hierarchy, where a physical-layer transceiver bridges a host controller or UART with a cable-based RS-232 communication port. The MAX3243's combination of multiple drivers, multiple receivers, and automatic power management makes it appropriate for multi-port industrial, instrumentation, and embedded systems. Key features include three RS-232 drivers, five RS-232 receivers, operation from 3 V to 5.5 V, and throughput up to 250 kbps. AutoShutdown reduces supply current when the receiver inputs do not detect a valid signal level, with the product family described as reaching 1 µA supply current. This can be valuable in systems where an RS-232 port is connected infrequently because the interface can reduce loading while the link is inactive. The MAX3243 family is designed for EIA/TIA-232 and V.28/V.24 communications interfaces. Three driver outputs support point-to-point serial links, while five receiver inputs provide additional monitoring channels. The family also includes an always-active receiver in the MAX3243 configuration, allowing a host to monitor another device even when the principal port is inactive. The E-qualified MAX3243 family adds enhanced ESD protection and automatic shutdown and wake-up behavior. Typical uses include industrial control consoles, laboratory instruments, POS terminals, configuration ports, and service interfaces for embedded equipment. The 250 kbps capability provides a useful margin over common low-speed serial links, while the 28-pin SOIC package supports conventional surface-mount assembly. Designers should preserve the RS-232 voltage levels at the connector and route the interface according to the manufacturer's recommended application circuit. Power-system design should account for transmit-state loading and supply-current changes as AutoShutdown detects valid receiver activity. Decoupling capacitors should be placed close to the supply and ground pins, and connector-side protection should complement the IC's internal ESD capability without excessive capacitance that could distort edges. Use the manufacturer pin-description table and recommended circuit when assigning tracks and selecting bypass components. This product page combines the confirmed electrical and packaging characteristics with practical interface-selection guidance, drop-in replacement constraints, and PCB implementation notes. It is intended to help engineers identify whether the MAX3243EWI+T provides the required channel count, speed, supply range, package, and protection for an RS-232 design.
MAX3243IDWRE4 - 3.3V RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX3243IDWRE4 is a 3.3V multichannel RS-232 line driver and receiver with a 3 V to 5.5 V supply range, integrated AutoShutdown current reduction, and ±15 kV human-body-model ESD protection. The device is packaged in a 28-pin SSOP-style surface-mount package and is designed for serial interface designs requiring multiple RS-232 channels. An RS-232 transceiver is an interface IC that combines differential line drivers with receivers so that logic-level signals can be transmitted between a digital system and an RS-232 port. The MAX3243IDWRE4 belongs to the multichannel RS-232 interface family, placing several driver and receiver functions in one package while reducing the number of external components required around the physical serial connection. The principal electrical features include operation from a 3 V to 5.5 V supply, CMOS-compatible logic interfaces, low supply current through the AutoShutdown feature, and ±15 kV ESD protection rated using the human-body-model test method. The operating-temperature specification for this ordering code is 0 °C to 70 °C. The device is identified as a 3/5 transceiver with 28 pins in an SSOP, 5.30 mm, MO-150 package. MAX3243-family devices are useful when a system must translate between CMOS/TTL-level UART signals and RS-232 levels. The integrated protection helps reduce the vulnerability of the interface pins to electrostatic discharge encountered during handling, connection changes, and normal industrial or commercial equipment use. The AutoShutdown function is intended to reduce supply consumption when valid signal activity is not detected. Typical applications include multi-channel serial ports, data acquisition and control systems, industrial communication equipment, test and measurement instruments, and embedded systems that need more than one RS-232 connection. When laying out the board, place the transceiver close to the connector and follow the manufacturer pin-description table for driver, receiver, supply, ground, and charge-pump connections. Add suitable bypass capacitance and route the RS-232 connector-side nets away from sensitive analog or high-speed digital traces. For a new design, verify the complete pinout and operating limits in the MAX3243 manufacturer datasheet before assigning connector signals or external protection components. The MAX3243IDWRE4 is appropriate when a 28-pin, 3.3V-compatible, multichannel RS-232 interface with integrated ESD protection is required, while the exact replacement must be checked for package, pinout, temperature rating, and lifecycle requirements.
MAX3243IPWRDL - 250kbps RS-232 IC | Texas Instruments
Texas Instruments MAX3243IPWRDL is a multichannel RS-232 line driver and receiver IC operating from 3 V to 5.5 V, with a maximum data rate of 250 kbps and ±15 kV ESD protection. The device is packaged in a 28-pin TSSOP, making it suitable for compact serial-interface equipment where logic-level UART signals must connect to external RS-232 ports. An RS-232 transceiver is an interface IC that combines line drivers, receivers, and charge-pump voltage conversion to translate between CMOS/TTL logic levels and the bipolar voltage levels used by RS-232. Within the interface hierarchy, it belongs to the RS-232 transceiver family, interface IC category, and broader data-communications semiconductor ecosystem. This multi-function integration reduces the number of external components required for a working serial port. The MAX3243 combines a 3 V to 5.5 V operating range with a 250 kbps maximum signaling rate. Its ±15 kV ESD protection is a key feature for systems exposed to electrostatic discharge through cables and connectors. The 28-pin TSSOP offers adequate pin density for multichannel RS-232 implementations while supporting automated surface-mount assembly. The manufacturer rates the MAX3243 family for 250 kbps operation, allowing it to support common serial-control links, point-to-point data channels, and legacy peripheral interfaces. Its integrated transceiver architecture is intended to simplify the external RS-232 interface compared with separate drivers, receivers, and charge-pump circuits. Design validation should confirm signal levels, timing, capacitance, and cable requirements against the application operating conditions. Typical uses include industrial control consoles, data-acquisition equipment, test-and-measurement instruments, communications adapters, and service-port interfaces. The part is particularly useful when a compact board needs multiple RS-232 lines, a 250 kbps data-rate ceiling, and stronger ESD protection than an unprotected transceiver. System designers should also allow for connector selection, signal-return routing, and appropriate chassis grounding. The principal design consideration is ensuring that every connected RS-232 signal uses the correct driver or receiver direction and that no device presents an inappropriate output conflict. Keep interface traces away from noisy power paths, use the datasheet-recommended charge-pump capacitors, and confirm the external line-termination arrangement before releasing a production layout. This page organizes the MAX3243IPWRDL electrical characteristics, sourcing information, drop-in candidates, application guidance, and PCB considerations into a design-oriented component reference. It also distinguishes documented functions from parameters that require confirmation against the current manufacturer datasheet before schematic release.
MAX3380EEUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices
The Analog Devices MAX3380EEUP+T is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35V to +5.5V operation, with a maximum data rate of 460 kbps and 20-pin TSSOP packaging. It integrates ESD protection rated at ±15 kV on the I/O and logic pins, making it suitable for serial data-cable equipment where both the RS-232 line and logic-side connections can be exposed to electrostatic discharge. An RS-232 transceiver is an interface IC that converts between single-ended RS-232 signals and TTL/CMOS-compatible logic. The MAX3380EEUP+T operates as a full-duplex interface with two transmit drivers and two receive receivers, allowing simultaneous bidirectional communication when the connected system provides the required ground and signal arrangement. Its low-power design is intended for portable instruments, data-cable applications, and embedded systems using mixed logic voltage levels. The device accepts supply voltages from +2.35V to +5.5V. The MAX3380EEUP+T uses a VL reference pin to support mixed-logic systems down to +1.65V, while the datasheet identifies the device as a +2.35V to +5.5V-powered EIA/TIA-232 and V.28/V.24 communication interface. The operating data rate reaches 460 kbps, which is suitable for higher-speed serial links used in instrumentation, industrial controls, and equipment interfaces. Its integrated protection is a key differentiator for external cable connections. The I/O and logic pins are specified for ±15 kV ESD protection, reducing the need for separate protection networks when the board layout follows the manufacturer's recommended connection guidance. The transceiver family also provides low power requirements and is designed for applications involving RS-232 cables, data acquisition, test equipment, and industrial control systems. Typical uses include RS-232 interfaces on laboratory instruments, point-of-sale terminals, industrial controllers, data loggers, and service equipment. The two transmitter and two receiver channels make it appropriate for systems that need more than one serial port or a full-duplex connection. The TSSOP-20 package supports compact surface-mount assembly while exposing the individual driver, receiver, logic-reference, supply, and ground connections required for a complete interface. When laying out the board, keep RS-232-side traces away from sensitive analog and logic signals, connect the transceiver supply and ground pins with low-inductance paths, and follow the datasheet recommendations for decoupling and external protection. Confirm the VL voltage before connecting the logic-side circuitry, especially when the host controller operates below the transceiver supply voltage. This product page combines the manufacturer specifications with practical interface considerations, package guidance, application examples, and drop-in alternatives. It helps engineers evaluate the MAX3380EEUP+T for data-cable equipment, industrial electronics, and embedded serial communication before completing the PCB footprint and protection strategy.
MAX338CSE+T - 8:1 CMOS Multiplexer | Analog Devices
Analog Devices MAX338CSE+T is an 8:1 low-leakage CMOS analog multiplexer with a maximum on-resistance of 400 ohm, operating from a single +4.5 V to +30 V supply or dual ±4.5 V to ±20 V supplies. The device is packaged in a 16-pin narrow SOIC and uses three binary address inputs to connect one of eight inputs to the common output. MAX338 is also described as a dual 4-channel configuration for compatible applications. An analog multiplexer is a semiconductor switch that routes multiple analog signals through one common signal path. It belongs to the analog switch and multiplexer hierarchy within interface ICs, enabling data acquisition, signal routing, and test systems to use fewer external components. The MAX338CSE+T is particularly useful where low leakage, TTL-compatible addressing, and flexible single- or dual-supply operation are important. The principal operating characteristics include a 400 ohm maximum on-resistance, low-leakage CMOS construction, and address controls that accept TTL input levels from +0.8 V to +2.4 V over the specified temperature and supply ranges. The analog multiplexer uses Maxim's 44 V silicon-gate process. These features make it suitable for precision signal selection where the selected channel must minimize interference with high-impedance sources. The single-supply configuration supports +4.5 V to +30 V, while dual-supply operation supports ±4.5 V to ±20 V. This versatility allows the same circuit architecture to handle positive-only systems and bipolar analog nodes. The 16-pin narrow SOIC package is surface mountable and provides a conventional footprint for compact instrumentation and industrial control equipment. Typical uses include data-acquisition systems, automated test equipment, battery and power-management monitoring, industrial measurement interfaces, and multiplexed sensor inputs. In these applications, the three address lines select one of eight channels while the common path carries the selected signal to a downstream amplifier, converter, or processing circuit. Designers should account for the 400 ohm on-resistance when driving the selected input. The source impedance, amplifier input bias current, injected charge, and leakage of the connected channel influence overall accuracy. Use the manufacturer's pin-description and typical-application information to assign address inputs, supply rails, enable control, and the common terminals. This product summary combines the manufacturer specifications, package information, functional cross-references, and practical routing guidance into a design-oriented reference. It highlights the electrical limits, supply flexibility, and substitution constraints needed to evaluate MAX338CSE+T before integrating it into a PCB.
MAX3485ECSA+T - 12Mbps 3.3V RS-485/RS-422 Transceiver | Analog Devices
The Analog Devices MAX3485ECSA+T is a 3.3 V-powered, slew-rate-limited true RS-485/RS-422 half-duplex transceiver rated for data rates up to 12 Mbps, with ±15 kV ESD protection on the bus pins, housed in an 8-pin SOIC (NSOIC-8) surface-mount package. An RS-485/RS-422 transceiver is a differential line-driver and line-receiver pair that lets two systems exchange data over a long, noisy cable. RS-422 is the balanced point-to-point standard, while RS-485 adds a multi-drop capability. Within the signal-chain hierarchy, a transceiver sits between a logic-level UART or microcontroller and a physical copper bus: UART logic levels enter the DI pin, the differential driver places Y and Z onto the cable, and the differential receiver returns a clean logic level on ROUT. A transceiver is therefore a physical-layer interface IC within the interface-IC category of semiconductor products. Key features of the MAX3485ECSA+T include a 3 V to 3.6 V single supply operation, one driver and one receiver in a single package, 12 Mbps maximum signalling rate, ±15 kV ESD protection on bus pins, and a slew-rate-limited driver that reduces EMI and ringing on long cables. Short-circuit current limiting and thermal shutdown protect the driver output during overload or bus contention conditions. Technically, the device combines a low-power differential driver with a fail-safe-tolerant receiver, so the receiver still resolves valid logic states when the bus is idle, partially terminated, or driven by another node. Because the driver edge rate is deliberately limited, the output spectrum is cleaner than a 12 Mbps-capable unlimited-rate driver, which makes the part easier to pass EMC pre-compliance testing in industrial cabinets. The single 3.3 V rail also allows direct interfacing with modern 3.3 V microcontrollers without level translation. Typical uses include industrial instrumentation links, building-automation nodes, RS-485 to RS-485 repeater and concentrator designs, POS and metering equipment, and any point-to-point or multi-drop field bus running at 3.3 V logic levels. When designing around this part, remember that the DE and /RE pins control direction, so pull both to a defined state at reset to avoid a floating bus. Also keep the Y and Z traces a matched, tightly coupled pair on a continuous ground plane to preserve differential impedance. This page consolidates distributor availability data, verified drop-in alternatives, a parameter-by-parameter comparison, and practical layout notes that are not found in a single place in the manufacturer datasheet.
MAX3488AEGSA+ - 20Mbps RS-422/RS-485 Transceiver | Analog Devices
The Analog Devices MAX3488AEGSA+ is a 3.3V-powered RS-422/RS-485 transceiver with one driver and one receiver, supporting data rates up to 20Mbps and ESD protection up to ±20kV. It is packaged in an 8-pin SOIC and is designed for industrial, instrumentation, and communications links requiring a compact, slew-rate-limited interface. An RS-485 transceiver converts a differential digital signal between a logic-level UART or controller and a balanced, noise-resistant cable. RS-422 is also differential, but it generally supports point-to-point or limited multi-drop topologies. The MAX3488AEGSA+ combines these functions in the interface IC category, placing physical-layer signaling between embedded logic and external cabling. Its low-power 3.3V operation also makes it suitable for modern portable and distributed systems. Key features include 20Mbps maximum data rate, ±20kV ESD protection, slew-rate-limited driver operation, and operation from a 3.3V supply. The slew-rate limitation reduces high-frequency EMI and helps limit reflections on longer cables, while ESD protection improves robustness when cables are connected or disconnected in industrial environments. The device provides one transmit driver and one receive receiver for compact point-to-point or multi-drop bus designs. The MAX3488A family uses differential signaling to reject common-mode noise and improve signal integrity over longer cable runs. Because the MAX3488AEGSA+ is slew-rate limited, engineers should select termination and biasing networks that match the cable length and topology. The 8-pin SOIC format simplifies assembly in designs that require a small, standard surface-mount footprint. Typical applications include industrial sensor networks, building automation equipment, robotics, process-control systems, remote I/O modules, and data acquisition equipment. The MAX3488AEGSA+ can also be used in point-to-point RS-422 links when both ends support the appropriate differential termination. In each case, the transceiver provides the physical layer while an external UART or microcontroller handles framing, addressing, and protocol functions. Designers should verify the supply voltage, driver enable polarity, receiver enable polarity, grounding, and termination requirements against the manufacturer datasheet. A common ground reference is important for reliable operation, while bias resistors should be placed so the bus remains in an idle state when no driver is enabled. Cable routing should preserve differential symmetry and minimize stubs. This product page combines the exact manufacturer and distributor specifications with practical interface-design guidance, package information, comparison data, and application-oriented design notes for engineers selecting or replacing an RS-422/RS-485 transceiver.
MAX3490ECSA+ - 3.3V 12Mbps RS-485/RS-422 Transceiver | Analog Devices
Analog Devices MAX3490ECSA+ is a 3.3 V powered, slew-rate-limited true RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. The family operates from a 3.3 V supply and supports communication rates up to 12 Mbps, making it suitable for high-speed industrial, instrumentation, and data-link applications. Its slew-rate-limited driver helps reduce unwanted signal transitions and electromagnetic interference on long printed-circuit-board and cabling interconnects. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back into CMOS-compatible logic. The MAX3490 family provides one transmit driver and one receive channel in each package, allowing designers to build bidirectional or point-to-point communication links while controlling bus direction with external circuitry. True RS-485 operation also supports multi-drop bus arrangements when the system includes the required termination and biasing networks. Key features include 3.3 V operation, data rates up to 12 Mbps, slew-rate-limited signaling, and enhanced ESD protection rated at ±15 kV according to the manufacturer product-page description. The MAX3490ECSA+ is identified as an 8-SOIC package variant and is part of the MAX3490 production family. The MAX3490 product family also includes related 3.3 V RS-485 and RS-422 transceivers, including the MAX3490E variant with a specified ±15 kV ESD rating. Typical applications include industrial control systems, factory automation equipment, building automation, instrumentation networks, data acquisition systems, and isolated or non-isolated communication links. The device can be used where a host controller, microcontroller, or programmable logic device must communicate with remote sensors, actuators, meters, or industrial modules over a balanced bus. Designers should pay attention to the difference between the manufacturer’s general MAX3490 family description, which lists 10 Mbps, and the MAX3490E and distributor descriptions, which list 12 Mbps for the relevant device variants. Confirm the exact ordering code and its data-sheet limits before using the part as the limiting element in a link budget. Keep the transceiver close to the connector, provide controlled return paths, and apply termination only where the board and cable topology require it. This page organizes the MAX3490ECSA+ specifications, packaging information, application guidance, comparison points, and practical interface-design considerations into a concise engineering reference for selecting and implementing a compact differential communications transceiver.
MAX365CSE+ - Quad SPST Analog Switch | Analog Devices
The Analog Devices MAX365CSE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, an 85 ohm on-resistance specification, and a 16-pin SOIC package. It is designed for routing low-voltage analog signals while maintaining low channel-to-channel resistance variation and a flat on-resistance characteristic across the signal range. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The MAX365 belongs to the analog switch hierarchy within interface ICs and signal-routing semiconductors. Unlike a mechanical relay, it can change connection states electronically with compact packaging and low external component requirements. The MAX365 is specifically configured as four normally open SPST switches, making each channel independent when the device supports separate control inputs. The MAX365 family provides on-resistance below 85 ohms across the analog signal range, with channel matching within 2 ohms and maximum on-resistance variation of 9 ohms. These characteristics help minimize signal attenuation and gain errors when different channels are selected in sequence. The four-channel architecture also allows one package to replace multiple individual switch functions in signal-routing designs. The manufacturer describes the MAX365 as a precision quad SPST analog switch with low on-resistance, low leakage, and power-off isolation. A 250 ns switching figure is associated with the device. Because the MAX365CSE+ uses normally open contacts, each switched path is disconnected until its corresponding control signal activates the channel. The exact supply-voltage range, control thresholds, leakage limits, and detailed timing conditions should be confirmed in the manufacturer data sheet before final circuit design. Typical uses include battery-powered test equipment, data-acquisition systems, analog signal multiplexing, precision measurement circuits, and industrial control interfaces. The device can also isolate signal sources when power is absent or when a system requires a controlled connection rather than a permanently closed path. Its 16-pin SOIC package supports conventional surface-mount assembly and compact board layouts. PCB design should keep each switched signal trace short and place input and output routing away from fast digital control or switching nodes. Verify the logic levels and supply rails against the manufacturer data sheet, especially in mixed 3.3 V and 5 V systems. Confirm whether normally open behavior is required, rather than selecting a normally closed alternative, because the open and closed families provide different default signal paths. This page combines the MAX365 family specifications, package information, application guidance, and pin-compatible family comparisons to support faster component selection and PCB design. It also organizes sourcing questions, replacement options, and practical implementation considerations around the exact MAX365CSE+ ordering code.
MAX398EGE - 8:1 Low-Voltage CMOS Analog Multiplexer | Analog Devices
Analog Devices MAX398EGE is an 8:1 precision, low-voltage CMOS analog multiplexer with less than 100 Ω on-resistance, channel-to-channel matching within 6 Ω, and on-resistance variation limited to 11 Ω maximum over the specified analog signal range. It is supplied in a 16-pin QFN package. The device routes one analog signal source to one of eight inputs, making it useful for precision measurement, signal conditioning, test systems, data acquisition, and instrumentation. An analog multiplexer is an analog switch array that connects a common terminal to one selected input channel. Within the interface-IC hierarchy, the MAX398EGE belongs to the analog switch and multiplexer family, where low and closely matched on-resistance reduce channel-dependent attenuation and error. Its monolithic CMOS construction is intended for low-voltage analog routing where repeatable channel behavior and compact implementation are important. The primary performance specifications emphasize resistance matching rather than resistance alone. Less than 100 Ω on-resistance limits insertion loss in the selected path, while matching within 6 Ω minimizes gain differences as the selected input changes. The 11 Ω maximum change across the specified analog range further limits signal-level distortion when the mux handles varying amplitudes. The 8:1 configuration also reduces the number of external routing connections required in multichannel analog front ends. The MAX398 part family is offered as an 8-channel or dual 4-channel precision multiplexer. This distinction matters because an 8:1 device presents eight selection inputs, while the dual 4:1 arrangement divides its resources into two independent 4:1 muxes. Circuit designers must therefore confirm pin-level functions, control logic, and package suffix before treating family members as substitutes. The MAX398EGE is the 8:1 member in the exact ordered variant identified here. Typical uses include multichannel sensor acquisition, automated test equipment, battery-cell measurement, industrial control systems, and laboratory instrumentation. In these systems, the common analog path can be connected successively to different sensors or test nodes while the surrounding ADC or measurement front end processes the selected signal. The low matched on-resistance helps preserve amplitude consistency across channels. PCB design should account for the QFN package, exposed thermal pad requirements, supply bypassing, and analog return-current paths. Keep the multiplexed signal traces short, use a continuous ground reference, and place input and bypass capacitors close to their associated pins. Review the MAX398EGE datasheet pin description table before assigning control and signal functions because the 16-pin layout includes multiple selection and common connections. This product record combines the manufacturer overview with package and circuit-level guidance, identifies verified drop-in alternatives where they exist, and adds practical selection criteria for analog routing. It distinguishes confirmed electrical characteristics from parameters that still require confirmation for a production design, helping engineers evaluate the MAX398EGE before layout release.
MAX4062EUB+ - Differential Mic Preamplifier, 2.4V-5.5V | Maxim
The Analog Devices (Maxim Integrated) MAX4062EUB+ is a differential-input microphone preamplifier with internal bias and complete shutdown, operating from a 2.4V to 5.5V single supply in a 10-pin uMAX (uSOP/MSOP) package. It provides adjustable gain with excellent power-supply rejection ratio (PSRR) and common-mode rejection ratio (CMRR), and integrates a low-noise microphone bias source, eliminating external bias components in voice-band signal chains. A differential microphone preamplifier is a small-signal audio amplifier that senses the voltage difference between an electret or MEMS microphone's output terminals and rejects common-mode interference picked up on the microphone lines. Within the signal-chain hierarchy (sensor -> preamplifier -> ADC/codec -> baseband), the microphone preamplifier is the first analog gain stage and largely determines the noise floor and dynamic range of a voice recording path. Differential input architectures are preferred in portable electronics because handset wiring is short, high-impedance, and exposed to RF and display noise. Key features of the MAX4062EUB+ include the integrated microphone bias generator, rail-to-rail output stage (Class AB per DigiKey categorization), complete shutdown for power savings in battery-operated systems, adjustable gain set by external resistors, and industrial temperature grade. The wide 2.4V to 5.5V supply range allows direct operation from a single Li-ion cell or a 3.3V/5V rail without a dedicated regulated supply. Architecturally, the device belongs to the MAX4060/MAX4061/MAX4062 family; the MAX4062 variant is the member with internal bias and complete shutdown. Excellent PSRR and CMRR keep display, RF, and switching-regulator noise out of the microphone path, a critical attribute for low-noise portable audio as stated in the Maxim/ADI datasheet general description. Typical applications are notebook PC microphone inputs, PDA voice recorders, smartphone/handset voice paths, and VoIP headsets - any battery-powered system where a differential electret or MEMS microphone must be amplified and biased from a limited power budget. Design-wise, set the gain with the external feedback resistors and verify that the bias source can supply the chosen microphone's current; place the bias-decoupling capacitor close to the bias pin to preserve noise performance. This page synthesizes distributor listing data, family cross-references, and practical design notes beyond what a plain datasheet mirror provides, with pricing as of 2026-10-12.
MAX456EPL+ - 8x8 35MHz Video Crosspoint Switch | Analog Devices
The Analog Devices MAX456EPL+ is an 8 x 8 monolithic CMOS video crosspoint switch with a bandwidth of 35 MHz, supplied in a 40-pin PDIP package. The device routes multiple video signals through a programmable crosspoint matrix, allowing eight inputs to be connected to eight outputs through independently controlled switching paths. Its 8 x 8 configuration, 35 MHz video bandwidth, and through-hole PDIP construction make it suitable for professional video routing, broadcast equipment, surveillance systems, and legacy analog video test installations. A video crosspoint switch is an interface IC that provides configurable signal paths between multiple source and destination channels. Within the broader signal-chain hierarchy, the MAX456 belongs to video switches, analog multiplexers, interface ICs, and semiconductors. Unlike a simple mechanical video switch, a crosspoint matrix can route many source signals to selected destinations electronically while reducing the component count, board area, and external interconnection complexity of a conventional relay-based matrix. The MAX456 integrates eight video inputs and eight outputs in one monolithic CMOS device. Its stated 35 MHz bandwidth supports baseband analog video signals, including composite video and other bandwidth-compatible analog sources. Independent matrix control allows operators or system logic to change routing configurations without physically reconnecting cables. The MAX456EPL+ is identified as an industrial-grade 40-pin PDIP version, supporting through-hole PCB assembly and conventional socket-compatible prototyping workflows. Because the MAX456 is an analog video crosspoint rather than a modern digital video processor, its useful design limits are defined by analog bandwidth, channel isolation, gain behavior, crosstalk, power requirements, and output drive. Those detailed electrical characteristics should be checked in the manufacturer datasheet before cascading multiple devices or driving long cable runs. The monolithic architecture can simplify a matrix implementation, but it does not eliminate the need for source termination, grounding, decoupling, and controlled impedance routing. Typical uses include television studio routing, CCTV control-room matrices, lecture-capture video distribution, analog video test equipment, and educational video laboratories. The 40-pin PDIP package is particularly useful where field replacement, socket use, or through-hole assembly has greater value than the smaller footprint of a surface-mount option. A one-channel signal can be routed among outputs by configuring the matrix, while full operation permits many simultaneous connections according to the switching commands supplied by the controlling electronics. The main layout consideration is analog signal integrity. Keep video traces short, maintain a continuous ground reference, decouple supply pins near the device, and avoid routing high-speed digital control or switching-node currents beneath sensitive video paths. Because the MAX456EPL+ is a through-hole device, also plan the connector orientation and analog ground strategy before fabrication. This page consolidates the device identity, package information, design guidance, application fit, and documented same-family alternative for engineers evaluating the legacy 8 x 8 video matrix. For new designs, verify lifecycle availability, electrical limits, and required switching logic before committing the 40-pin PDIP footprint. Request a Quote through the form on this page for current commercial conditions, and consult the manufacturer datasheet for the definitive pin description, timing, power, and analog performance tables.
MAX4850ETE+T - Dual SPDT Analog Switch | Maxim Integrated
The Maxim Integrated MAX4850ETE+T is a dual-channel, single-pole double-throw analog switch with over-rail signal handling, packaged in a 16-TQFN surface-mount package measuring 3 mm by 3 mm. The device provides two independently selectable SPDT switch paths and is identified for industrial-temperature operation, making it suitable for compact analog and mixed-signal routing systems. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The MAX4850ETE+T belongs to the analog-switch hierarchy within interface ICs: each SPDT path can route a common signal toward one of two external nodes, while the companion control logic determines which branch is connected. This capability is useful when a system must route audio, data, test, or control signals without changing the physical layout of the printed circuit board. The MAX4850ETE+T provides two switch channels in one compact 16-TQFN package. Its over-rail signal-handling characteristic allows the switch to remain operational when signal levels approach or extend beyond the supply rails, a useful condition in systems where transitions can overshoot nominal voltage ranges. The small 3 mm by 3 mm footprint also reduces board area compared with discrete switch implementations. This device is categorized as a high-bandwidth analog switch IC. Its two SPDT channels support signal-path multiplexing where one common input must be routed between alternative destinations. Such architecture is frequently encountered in audio equipment, USB-interface routing, test systems, communication modules, and control boards that require compact, electronically controlled routing. Typical uses include selecting an audio source, directing signals through an interface module, switching USB-related signal paths, and implementing compact test fixtures. The industrial temperature grade and surface-mount construction suit professionally designed equipment that must combine multiple routed channels without allocating separate packages for each switch. Designers should verify supply voltage, signal swing, bandwidth, on-resistance, leakage, and channel logic polarity against the manufacturer datasheet for the exact operating point. Because the TQFN package has a compact exposed-pad construction, PCB thermal management and soldering-process controls should follow the manufacturer’s land-pattern and reflow guidance. This page organizes the exact package, channel, mounting, and ordering information for MAX4850ETE+T while adding engineering-focused comparisons and application guidance. It helps engineers identify the switch function, verify the footprint, and assess the signal-routing use cases before beginning board-level design.
MAX4855ETE+ - 0.75Ω Dual SPDT Audio Switch | Analog Devices
The Analog Devices MAX4855ETE+ is a dual SPDT analog audio switch with integrated comparators, 0.75 Ω on-resistance, and a 16-pin thin QFN package measuring 3 mm × 3 mm. It operates from 2 V to 5.5 V, supports audio-signal routing over -40°C to +85°C, and is designed for space-constrained portable audio equipment. An analog switch is an integrated circuit that routes low-frequency analog signals between circuit nodes under digital control. The MAX4855 belongs to the analog-switch and multiplexer hierarchy, where SPDT means single-pole, double-throw: one common terminal can be connected to either of two switched terminals. This makes the device useful for selecting audio paths, supporting speaker-to-headset routing, and implementing controlled source selection within portable consumer electronics. Key features include two independently controlled SPDT channels, 0.75 Ω on-resistance, operation across a 2 V to 5.5 V supply range, and integrated comparators. The low on-resistance helps limit signal attenuation in audio paths, while the compact 3 mm × 3 mm package saves board area in cell phones, notebook computers, PDAs, and other handheld devices. The manufacturer identifies audio-signal routing and speaker-headset switching as principal applications. Each switch channel uses a common terminal and two selectable terminals, with control logic determining the active signal path. Integrated comparators can assist in detecting or controlling signal conditions without requiring separate comparison circuitry. The device uses a CMOS implementation and is specified in a TQFN-16 package, identified by package code MO-220-WEED in distributor documentation. The + suffix denotes the lead-free ordering option, while ETE identifies the extended-temperature 16-pin TQFN package configuration. Typical deployments include headphone and headset routing, audio accessory selection, portable-device input selection, and compact audio-signal switching. Because the MAX4855 handles analog paths rather than high-speed data, its principal design concerns are acceptable insertion loss, off-state leakage, control compatibility, exposed-pad grounding, and clean supply bypassing rather than digital edge-rate performance. In layout, place input and output routing close to the switched pins to minimize parasitic capacitance and pickup. Connect the exposed thermal pad and ground pins according to the manufacturer land pattern, provide local supply decoupling, and keep control traces away from sensitive audio paths. Verify that the selected signal amplitude and supply voltage remain inside the device's stated operating limits. This page consolidates manufacturer specifications, distributor availability, application guidance, sourcing information, and design cautions into one engineering reference. It also distinguishes verified facts from parameters that still require confirmation from the full datasheet, helping designers avoid assuming unreported electrical limits or pin functions.