Interface ICs
ژێرپۆلەکان
بەرهەمەکان (560+)
SN65HVD10P - 3.3V 32Mbps RS-485 | Texas Instruments
The Texas Instruments SN65HVD10P is a 3.3 V half-duplex RS-485 transceiver rated for 32 Mbps signaling and housed in an 8-pin PDIP (P) package. It combines a three-state differential line driver with a differential receiver in one IC, allowing a design to transmit and receive over the same balanced RS-485 bus. The device operates from a single 3.3 V supply and is specified over -40 °C to +85 °C. An RS-485 transceiver is an interface IC that converts logic-level signals into differential voltages for a balanced communication bus and converts received differential voltages back into CMOS-compatible logic. The RS-485 interface belongs to the interface-IC hierarchy and supports robust, multipoint data links used in industrial automation, instrumentation, building controls, and communications equipment. Differential signaling improves noise immunity by comparing the voltage between two conductors rather than relying on a signal measured against ground. The SN65HVD10P supports operation at 32 Mbps, making it suitable for data links that require substantially more signaling speed than conventional low-speed RS-485 equipment. Its three-state driver permits the bus driver to be disabled when the node is not transmitting. Available bus-pin ESD protection exceeds 16 kV using the HBM test method, according to the retrieved technical description. The family also provides a 1/8-unit-load option capable of supporting as many as 256 nodes on a bus. The device is designed for balanced transmission lines and meets or exceeds ANSI TIA/EIA-485-A and ISO 8482:1993 requirements, as stated on the Texas Instruments family page. This makes it applicable to both industrial control networks and shorter, high-speed interconnects where point-to-point communication is suitable. Because its package is through-hole PDIP rather than a surface-mount package, the SN65HVD10P is particularly convenient for prototypes, leaded industrial assemblies, and designs that favor easy inspection or rework. Typical uses include industrial sensor gateways, factory automation controllers, building-automation nodes, instrumentation links, and communication ports that exchange data at rates up to 32 Mbps. Half-duplex operation means the connected nodes share the bus and must avoid transmitting simultaneously. The bus direction can be controlled by a host or network controller, while receiver logic remains available for monitoring the bus according to the system architecture. PCB implementation should preserve the differential pair as a continuous, impedance-controlled route from the transceiver to the bus connector. Place termination, biasing, protection, and any required isolation close to their associated bus nodes, and route the pair away from switching nodes and high-current paths. Because the verified source data does not provide the complete pin table or recommended external-component values, those details should be confirmed in the manufacturer datasheet before layout release. This product page consolidates verified manufacturer specifications, distributor availability references, same-family drop-in candidates, and practical RS-485 design considerations. It also distinguishes confirmed parameters from information that still requires engineering review, helping designers evaluate the SN65HVD10P for industrial, automation, and high-speed balanced-bus applications.
SN65HVD11 - 3.3V RS-485 Transceiver | Texas Instruments
The SN65HVD11 is a 3.3-V RS-485 transceiver from Texas Instruments that combines a 3-state differential line driver and a differential input line receiver in a single 8-pin SOIC package. It operates from a single 3.3-V power supply and is designed for balanced transmission lines, meeting or exceeding ANSI TIA/EIA-485-A and ISO 8482:1993 standards. The device supports data rates up to 10 Mbps and features bus-pin ESD protection exceeding 16 kV HBM, making it robust for industrial and building automation networks. RS-485 is a standard for serial communication systems that use differential signaling to transmit data over long distances and in noisy environments. The SN65HVD11 belongs to the family of RS-485 transceivers, which are essential components in industrial control networks, building automation, and other multi-point data acquisition systems. These transceivers convert logic-level signals to differential voltages that can be transmitted over twisted-pair cables, providing immunity to common-mode noise and enabling communication over distances up to 1200 meters. Key features of the SN65HVD11 include a 1/8 unit-load option that allows up to 256 transceivers on a single bus, a wide common-mode input range of -7 V to +12 V, and a low quiescent current of 1.1 mA typical. The device also features thermal shutdown protection and a 3-state output for bus sharing. The 8-pin SOIC package (D) is industry-standard, ensuring compatibility with existing PCB layouts. The SN65HVD11 uses a Power BiCMOS process, which combines low power consumption with high-speed operation. The differential driver outputs a minimum of 1.5 V across a 54-ohm load, while the receiver has a sensitivity of ±200 mV. The device is specified for operation over the industrial temperature range of -40°C to +85°C, making it suitable for harsh environments. Typical applications include industrial automation, building automation, HVAC systems, and point-of-sale terminals. The SN65HVD11 is also used in motor control and power inverter systems where reliable communication over long distances is required. Its high ESD protection and wide common-mode range make it ideal for factory floor networks. When designing with the SN65HVD11, ensure proper termination (120-ohm) at both ends of the bus and use a bias network to maintain a defined idle state. The driver enable (DE) and receiver enable (RE) pins allow for half-duplex operation, and the device can be placed in a low-power shutdown mode by driving both pins high.
SN65HVD11D - 3.3V RS-485 Transceiver | Texas Instruments
The Texas Instruments SN65HVD11D is a 3.3 V differential transceiver combining a three-state differential line driver and a differential line receiver in an 8-pin SOIC package. The device supports RS-485 and RS-422 balanced transmission applications, uses a single 3.3 V supply, and provides a one-eighth unit-load option supporting up to 256 nodes. Bus-pin ESD protection exceeds 16 kV HBM, making the part suitable for industrial equipment exposed to electrostatic discharge on external communication lines. A differential transceiver is an interface IC that transmits and receives data across a balanced pair of conductors. The driver converts a single-ended logic input into complementary differential outputs, while the receiver converts the differential bus voltage into a single-ended logic output. In the RS-485 hierarchy, the SN65HVD11D belongs to the class of multipoint differential bus interface ICs used by industrial automation, test equipment, building controls, and communications equipment. Key features include operation from a 3.3 V power supply, three-state driver output, differential receive capability, one-eighth unit-load operation, and bus-pin ESD protection exceeding 16 kV HBM. The low unit loading allows multiple nodes to share a bus while controlling the loading presented by each receiver. The three-state output also permits multiple drivers to be connected to a shared bus when only one driver is enabled at a time. The SN65HVD11D family is designed for balanced transmission lines and is stated to meet or exceed ANSI TIA/EIA-485-A and ISO 8482:1993. Its differential signaling improves noise immunity by deriving the receiver decision from the voltage difference between the A and B conductors rather than from either conductor relative to ground. This makes it appropriate for longer cable runs and electrically noisy factory environments when implemented with proper termination and biasing. Typical uses include industrial RS-485 multidrop buses, factory sensor networks, building-automation controllers, instrument interfaces, and point-to-point RS-422 links. The eight-pin SOIC package supports conventional surface-mount assembly, while the low unit loading helps preserve bus loading margin as more nodes are added. PCB design should provide a continuous return or reference path, route the differential pair together with matched spacing, and place termination and fail-safe bias components at physically appropriate bus locations. The supply should be decoupled close to the device, and unused digital inputs should not float. Bus protection, surge-current requirements, and cable length must be checked against the complete system rather than inferred from the transceiver rating alone. This page combines verified manufacturer and distributor information, practical RS-485 design guidance, a same-package alternative comparison, and structured selection criteria. These details help engineers distinguish genuine footprint-compatible options from parts that only provide similar RS-485 functionality.
SN65HVD12D - 3.3V RS-485 Transceiver | Texas Instruments
Texas Instruments SN65HVD12D is a 3.3 V differential transceiver for half-duplex RS-422 and RS-485 balanced communications, housed in an 8-pin SOIC package. It combines a 3-state differential line driver with a differential line receiver and supports a maximum signaling rate of 1 Mbit/s. The device provides bus-pin ESD protection exceeding 16 kV HBM and is offered in a 1/8 unit-load option supporting up to 256 nodes on a bus. An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over long, noise-prone industrial cabling. The SN65HVD12 belongs to the RS-485 transceiver hierarchy, which includes half-duplex driver/receiver combinations and is widely used where multiple nodes share a two-wire bus. Its differential signaling improves common-mode rejection by comparing the voltage between two conductors rather than referencing the signal to ground. The SN65HVD12D operates from a single 3.3 V supply and supports both RS-422 and RS-485 networks. Its 3-state driver output can be disabled when the device is not transmitting, allowing multiple drivers to share the same bus. The 1 Mbit/s maximum data rate supports moderate-speed industrial links, while the low unit load permits a comparatively large number of connected nodes. Bus-pin ESD protection exceeding 16 kV HBM improves robustness during installation and industrial handling. According to the Texas Instruments manufacturer datasheet and product page, the SN65HVD12 family meets or exceeds ANSI TIA/EIA-485-A and ISO 8482:1993 requirements. The SN65HVD12D is a half-duplex, one-transmitter, one-receiver device in the 8-SOIC package. Its balanced differential driver and receiver make it appropriate for point-to-point RS-422 links and multipoint RS-485 buses when node count, cable length, topology, and termination remain within the applicable network design limits. Typical uses include industrial automation controllers, sensor gateways, building automation equipment, factory data acquisition, motor-control interfaces, and embedded serial buses. The 3.3 V supply aligns with modern controller logic levels, while the 1/8 unit-load option allows multiple low-power nodes to share a bus. The same-package footprint and 3.3 V operating class can simplify replacement evaluation when comparing qualified RS-485 transceivers for an existing 8-SOIC board. Designers should provide correct bus biasing, termination, protection, and grounding rather than relying on the transceiver alone for network reliability. Place the transceiver close to the connector, route the differential pair as a tightly coupled pair, and minimize stub lengths. Verify that external protection devices clamp transients within the device ratings and confirm driver-enable and receiver-enable timing in the system firmware. This page combines verified manufacturer and distributor information with same-package replacement guidance, application-specific design notes, and a parameter comparison. It distinguishes documented drop-in candidates from choices that require package, logic, speed, or qualification review, helping engineers preserve PCB compatibility while evaluating supply and lifecycle risk.
SN65HVD20P - Extended Common-Mode RS-485 Transceiver | TI
Texas Instruments SN65HVD20P is an extended common-mode RS-485 transceiver with one driver and one receiver, supplied in an 8-pin PDIP package. It is designed for industrial communication networks using twisted-pair cabling and combines an RS-422/RS-485 transceiver with extended common-mode operation, wide receiver hysteresis, high ESD protection, and failsafe behavior. The device supports half-duplex communication and is identified by the SN65HVD20P PDIP ordering suffix. An RS-485 transceiver is an interface IC that converts logic-level signals between a host controller and a differential, balanced cable. The transmitter drives complementary differential outputs, while the receiver converts the differential input back into a logic signal. This differential signaling improves noise immunity over longer interconnects and is widely used in industrial automation, building controls, instrumentation, and communications equipment. The SN65HVD20 belongs to the RS-485 transceiver family within interface ICs and broader semiconductor communication devices. The principal feature of the SN65HVD2x family is its extended common-mode range. According to the Texas Instruments SN65HVD2x datasheet, the family operates over an extended range of common-mode voltages beyond typical RS-485 devices while meeting the requirements of the TIA/EIA-485-A standard. The family also provides high ESD protection, wide receiver hysteresis, and failsafe operation, making it suitable for noisy industrial environments where ground-potential differences can occur between connected equipment. The SN65HVD20P provides one transmit and one receive channel and operates in a half-duplex RS-422/RS-485 arrangement. Its PDIP package provides through-hole mounting and thermal reliability for industrial control equipment where surface-mount-only packages may be inconvenient. Exact propagation-delay, data-rate, common-mode, and supply-current limits should be selected against the operating requirements in the manufacturer datasheet before placing the part into a new bus design. Typical applications include RS-485 industrial control networks, factory automation equipment, remote sensor interfaces, building-management systems, data-acquisition equipment, and communications between controller boards separated by different ground potentials. In these systems, the transceiver serves as the physical-layer interface between a microcontroller or programmable logic controller and a field bus. Cable length, topology, termination, biasing, and common-mode voltage determine whether the selected transceiver provides adequate signal margin. For a new board, preserve the manufacturer-recommended decoupling near the supply pins, connect the driver and receiver grounds carefully, and install termination only at appropriate physical ends of the bus. The SN65HVD2x extended common-mode capability can improve tolerance to ground offsets, but it does not remove the need for twisted-pair routing, controlled-impedance layout, surge protection, and a correctly engineered bus. Use the pin-description table and application information in the manufacturer datasheet when assigning signals and defining the board footprint. This product page combines the manufacturer identification, package information, sourcing references, drop-in replacement guidance, comparison parameters, and practical design notes needed to evaluate the SN65HVD20P for an industrial differential-communication design.
SN65HVD230QDRQ1 - 3.3V CAN Transceiver AEC-Q100 | Texas Instruments
The Texas Instruments SN65HVD230QDRQ1 is an automotive-catalog 3.3-V CAN bus transceiver with standby mode, delivering data rates up to 1 Mbps in an 8-pin SOIC (D) package qualified to AEC-Q100 for automotive applications. A controller area network (CAN) transceiver is a physical-layer interface IC that converts the logic-level TXD and RXD signals of a CAN controller into the differential CANH and CANL bus signals defined by the ISO 11898-2 High Speed CAN Physical Layer standard. Within the interface IC hierarchy, it sits between the protocol controller and the twisted-pair bus, providing driver, receiver, ESD protection, and fault-tolerance functions for the network node. Key features include ISO 11898-2 compatibility, a low-current standby mode drawing approximately 370 uA typical, bus-pin ESD protection exceeding 15 kV HBM (exceeding 2000 V per MIL-STD-883 on the device), controlled driver output transition times for improved signal quality, and a dominant-timeout feature. An unpowered node does not disturb the bus, and the RS pin selects slew-rate control or low-power mode. The SN65HVD230Q family (SN65HVD230Q, SN65HVD231Q, SN65HVD232Q) was designed to pair directly with TI TMS320Lx240x 3.3-V DSPs with on-chip CAN controllers, and also serves as a low-power replacement for the classic PCA82C250 footprint. Operating from a single 3.3-V rail eliminates level shifting when the host MCU or DSP is a 3.3-V device, reducing BOM count and board area in automotive body electronics, gateway modules, and industrial CAN nodes. Typical applications include automotive body control modules, battery management systems with 3.3-V MCUs, industrial 3.3-V CAN networks, and building automation nodes where a 5-V supply is unavailable. Design consideration: the RS pin mode selection determines standby and sleep behavior - drive or tie it so the node can wake the transceiver from its 370 uA standby state when bus activity resumes, and provide a 4.7 kOhm to 10 kOhm split-termination network on CANH/CANL per ISO 11898-2 layout practice. This page synthesizes verified distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SN65HVD234QDRQ1 - 3.3V Automotive CAN Transceiver | Texas Instruments
The Texas Instruments SN65HVD234QDRQ1 is a 3.3-V automotive-qualified CAN bus transceiver that delivers up to 1 Mbps data rate in an 8-pin SOIC (D) package. Operating from a 3 V to 3.6 V supply with a typical operating current of 6 mA, it is AEC-Q100 qualified and designed to interface a CAN controller with the physical bus in 3.3-V automotive and industrial systems. A CAN (Controller Area Network) transceiver is a physical-layer interface IC that converts the TTL-level TX and RX signals of a CAN controller into the differential CANH/CANL bus signals defined by ISO 11898. Positioned between the protocol controller and the twisted-pair bus in the system hierarchy, the transceiver determines bus robustness, fault tolerance, and power consumption of the entire CAN node. Key features include a 1 Mbps maximum signaling rate, fault-protected bus pins, and the SN65HVD234-Q1 variant's ultralow-current sleep mode: applying a low level to the EN pin (pin 5) disables both driver and receiver, drastically reducing node current consumption for battery-connectedECU domains. The device wakes when a high logic level is reapplied to pin 5. The SN65HVD233-Q1, SN65HVD234-Q1, and SN65HVD235-Q1 family members share pinout and package, differing mainly in feature set. The architecture includes an internal TXD-to-RS pin loopback that assists the CAN controller with baud-rate detection (autobaud function), simplifying firmware in systems where the bus speed is not fixed. Differential driver and receiver stages provide common-mode bus tolerance suitable for harsh automotive electrical environments. Typical applications include automotive body control modules, instrument clusters, gateway ECUs, and industrial 3.3-V CAN nodes where low-voltage logic directly interfaces the CAN controller (e.g., 3.3-V MCUs such as TMS320F280xx and MSPM0 devices) without level shifting. Design tip: respect the 3.6 V absolute maximum supply and place a 0.1 uF decoupling capacitor directly at VCC; control the EN pin carefully during startup to avoid unintended bus dominant states.
SN65HVD255DR - 1Mbps Turbo CAN Transceiver | TI
The Texas Instruments SN65HVD255DR is a Turbo CAN transceiver designed for highly loaded Controller Area Network (CAN) networks with data rates in excess of 1 Mbps. It is packaged in an 8-pin SOIC (D) surface-mount package and operates over an extended temperature range of -40C to +125C, implementing the ISO 11898-2 High-Speed CAN physical layer standard. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the twisted-pair bus, converting controller TXD/RXD logic signals into differential CANH/CANL signals. Within the CAN system hierarchy (application layer, protocol controller, transceiver, bus), the transceiver provides the drive strength, common-mode tolerance, and ESD/fault robustness required for reliable communication in harsh electrical environments. Key features include fast loop propagation times that enhance timing margins on long, heavily loaded networks; functional-safety-oriented features per the TI datasheet; dominant and recessive output drive compliant with ISO 11898-2; and internal protection including thermal shutdown and short-circuit current limiting. The device operates from a nominal 5V supply. Low electromagnetic emission and high immunity make it suitable for demanding automotive and industrial buses. Typical applications include industrial automation and motor drives, building and climate control automation, security systems, and telecom base station status and control networks. In these systems the Turbo CAN fast loop times allow more nodes, longer cable runs, or higher bit rates than standard transceivers. When designing with the SN65HVD255DR, terminate both bus ends with 120-ohm resistors, place a 0.1uF bypass capacitor close to VCC, and keep the CANH/CANL traces symmetric and short to preserve signal integrity at extended data rates.
SN65HVD255QDRQ1 - 3.3V Turbo CAN Transceiver Q1 | TI
The Texas Instruments SN65HVD255QDRQ1 is an AEC-Q100 qualified 3.3V Turbo CAN transceiver delivering data rates in excess of 1 Mbps with fast loop times, housed in an 8-pin SOIC (D) package for highly loaded automotive and industrial CAN networks. A CAN transceiver is a physical-layer interface device that converts the single-ended TTL logic levels of a CAN protocol controller into the differential signaling on a twisted-pair CAN bus, and back again at the receiver. Within the interface IC hierarchy, it sits between the CAN controller (often integrated in an MCU) and the two-wire physical bus, providing dominant/recessive driving, bus fault protection, and receiver filtering. Key features include turbo-mode operation supporting data rates beyond 1 Mbps on short networks, enhanced loop-time symmetry for large and heavily loaded networks, single-supply 3.3V operation, and ISO 11898 physical-layer compatibility. The device integrates short-circuit protection, thermal shutdown, and wide common-mode bus voltage tolerance for robust operation in harsh electrical environments. The proprietary transceiver architecture of the SN65HVD25x Turbo family delivers fast loop times that improve arbitration success and bit-timing margin in highly loaded network nodes, distinguishing it from standard 1 Mbps transceivers. Receiver input impedance and bus biasing are optimized for large networks with many nodes, and the family datasheet (Rev. D) adds features oriented toward functional safety. The RS pin selects between slope-control and high-speed (turbo) operation, letting one design cover both EMC-sensitive and maximum-speed segments. Typical applications include automotive body electronics and gateway nodes, industrial PLC and motor-control CAN networks running at 3.3V logic, and high-data-rate buses where standard transceivers cannot sustain signal integrity above 1 Mbps. Design tip: size the bus termination at 120 ohms, verify dominant-state current limits when operating in turbo mode, and place a 0.1 uF local decoupling capacitor at VCC. This page synthesizes verified distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone. Prices referenced as of 2026-09-01.
SN65HVD3085EDR - 5V Half-Duplex RS-485 Transceiver | TI
The Texas Instruments SN65HVD3085EDR is a low-power, half-duplex RS-485 transceiver in an 8-pin SOIC (D) package, powered from a single 5V supply and fully compliant with the TIA/EIA-485A standard. It integrates one driver and one receiver for bidirectional communication on twisted-pair data bus networks, with controlled transition times suited to long cable runs. An RS-485 transceiver is a differential line interface IC that converts single-ended logic signals into balanced differential signals for robust serial communication. Within the interface IC hierarchy, it sits between a UART/MCU and the physical twisted-pair bus, providing the electrical drive, receiver threshold, and bus-fault tolerance defined by the TIA/EIA-485A standard. Key features include operation from a 4.5V to 5.5V supply, signaling rates up to 20 Mbps (per the SNx5HVD308xE family data), a small SOIC-8 footprint, and an operating temperature range of -40C to +85C. Controlled driver output transition times reduce EMI and reflections, while the low-power design minimizes quiescent supply current for multi-node networks. Architecturally, the device uses a differential driver with three-state outputs and a differential receiver with fail-safe inputs. Driver (DE) and receiver enable (/RE) pins allow half-duplex direction control from a standard MCU GPIO. Bus pins A and B tolerate the fault conditions required by the RS-485 standard, supporting reliable operation in electrically noisy industrial environments. Typical applications include industrial automation and Modbus RTU networks, building and HVAC control buses, battery-management and motor-control communication links, and point-to-multipoint serial links over twisted pair. The 20 Mbps class speed also suits fast industrial backbones needing short frame times. Design tip: use fail-safe biasing resistors on the A/B bus lines and terminate both cable ends with 120 ohm resistors to prevent reflections and receiver chatter on idle buses. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not consolidated in the manufacturer datasheet. Pricing references as of 2026-08-29 (LCSC from $0.3185).
SN65HVD31D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments
Texas Instruments SN65HVD31D is a 3.3 V full-duplex differential line transceiver supporting RS-422 and RS-485 communication in an 8-pin SOIC package. It combines one differential line driver and one differential-input line receiver, with separate driver input, driver enable, receiver enable, receiver output, supply, and ground connections. The device operates from a 3 V to 3.6 V supply and is specified for cable runs of up to 1500 meters. A differential line transceiver is an interface IC that converts logic-level signals into balanced differential outputs and converts differential bus signals back into logic-level data. This electrical layer sits between a UART, microcontroller, industrial controller, or other digital controller and a wired communication bus. For RS-485 systems, the SN65HVD31 family provides full-duplex operation, allowing the transmitter and receiver to operate simultaneously rather than sharing a single half-duplex bus pair. The 3 V supply operation suits modern 3.3 V digital systems and helps simplify power architecture around low-voltage processors. Its SOIC-8 package supports conventional surface-mount assembly and provides sufficient pin separation for a communication interface exposed to electrically noisy industrial environments. The operating-temperature option identified for SN65HVD31D extends from -40 °C to 85 °C, covering industrial temperature requirements. The separate enable inputs provide control over the driver and receiver paths independently. This flexibility is useful when a system needs to isolate a transmitter during bus turnaround, control a receiver during reset, or implement a multidrop full-duplex network. The separate differential driver and receiver pins also permit dedicated transmit and receive cabling, which is the defining architectural feature of a full-duplex bus implementation. Typical uses include industrial serial links, building-control networks, factory equipment, data-acquisition systems, instrumentation, and communications between circuit cards separated by long cable runs. Because the device implements both RS-422 and RS-485 signaling, engineers can apply it to balanced differential links where noise immunity and signal integrity are more important than single-ended signaling. PCB design should route the differential driver and receiver traces as a controlled-impedance pair, place termination and protection components where their electrical roles are clear, and keep switching currents away from sensitive logic. Confirm the completed interface against the manufacturer datasheet for bus loading, enable timing, maximum data rate, receiver thresholds, and power-supply decoupling before releasing a production design. This page combines manufacturer device information, verified ordering details, engineering application guidance, package-aware alternatives, and a parameter comparison to support faster component selection and board-level implementation planning.
SN65HVD35D - 3.3V Full-Duplex RS-485 Transceiver | Texas Instruments
The Texas Instruments SN65HVD35D is a 3.3 V full-duplex RS-485 and RS-422 transceiver with separate driver and receiver enable pins, packaged in a 14-pin SOIC (MS-012AA) surface-mount package. It operates from a 3 V to 3.6 V supply, supports signaling rates up to 1 Mbps with optional 5 Mbps and 25 Mbps driver transition-time options, and offers a 1/8 unit-load receiver that supports up to 256 nodes on a single bus. An RS-485 transceiver is the physical-layer building block for balanced, differential, two-wire multidrop data buses. The SN65HVD3x family combines a 3-state differential line driver, a differential line receiver, and the enable logic needed to put each side into a high-impedance state. In the SN65HVD35D, the driver enable is active high and the receiver enable is active low, so a host microcontroller can drive the bus and listen independently, which is essential for full-duplex designs such as point-to-point links and multi-drop industrial field buses. Key features include bus-pin ESD protection exceeding 15 kV HBM, a low-current standby mode drawing only 1 uA, glitch-free receiver outputs that prevent false start bits during noise transients, and a receiver input hysteresis of 50 mV that rejects differential noise at the input comparator. The device also supports RS-422 signalling and cable runs of up to 1500 meters in the appropriate system configuration. Internally, the SN65HVD3x family uses a differential receiver with internal hysteresis and an output driver stage with selectable edge-rate control, giving designers a way to reduce EMI on slow networks without giving up throughput on fast links. Separate input and output pins for both the driver and receiver make bus-direction control straightforward at the digital side. Typical applications include industrial RS-485 fieldbus transceivers, building and HVAC automation controllers, industrial sensor and actuator nodes, instrumentation over long twisted-pair runs, and point-to-point links between a microcontroller and a peripheral board using a separate transmit and receive pair. When laying out the board, keep the A and Y (and B and Z) differential pair routed as a tightly coupled pair over a continuous ground reference, and place the bus-side protection and termination network close to the connector. Because the transceiver is a 3.3 V device, its bus-side interface does not provide isolation or level translation for 5 V legacy nodes, so a galvanic barrier should be added when the far end of the cable is at a different ground potential. This page consolidates the key electrical ratings, drop-in replacement options within the SN65HVD3x family, and practical layout guidance for engineers who need to bring a full-duplex RS-485 node onto a 3.3 V board with a 14-pin SOIC footprint.
SN65HVD70D - 3.3V Full-Duplex RS-485 Transceiver | TI
The Texas Instruments SN65HVD70D is a 3.3 V full-duplex RS-485 transceiver with a 400 kbps data rate, 12 kV IEC ESD protection, and individual driver and receiver enables, packaged in a 14-pin SOIC (D). It combines one driver and one receiver in a single circuit, allowing simultaneous bidirectional communication over a balanced RS-485 bus. An RS-485 transceiver is an interface IC that converts logic-level signals to and from differential bus voltages. This differential signaling supports noise-resistant, long-distance communication between industrial, communications, and instrumentation systems. Full duplex requires separate differential driver and receiver connections, while the enable inputs allow each direction to be disabled when not required. The SN65HVD70D operates from a 3.3 V supply and supports signaling rates up to 400 kbps. Its ESD protection includes greater than 30 kV human-body-model exposure and greater than 12 kV IEC 61000-4-2 contact discharge. These protections reduce the risk of electrostatic damage to the bus interface, although correct board-level grounding and surge design remain necessary. The device uses differential signaling to reject common-mode noise, and its large receiver hysteresis improves tolerance of conducted differential noise. The SN65HVD70D is suitable for bidirectional links where the transmitter must remain enabled during reception or where independent direction control is required. Its 14-pin SOIC package supports conventional surface-mount assembly. Typical uses include industrial control networks, factory automation equipment, building automation interfaces, communication adapters, and external bus-powered controllers. The separate enable controls can also simplify direction-control logic when the host controller drives the interface directly rather than using an automatic transceiver controller. For reliable operation, route the differential pair as a tightly coupled pair, provide a low-impedance return path, place termination only at the two physical ends of the bus, and avoid stubs. Verify enable polarity and bus idle states in firmware because incorrect direction timing can create a contention condition on the bus. This product page combines the manufacturer interface specifications with packaging guidance, application examples, comparison criteria, and drop-in replacement considerations to support faster component selection and PCB implementation.
SN65HVD78D - 3.3V 50Mbps Half-Duplex RS-485 | TI
The Texas Instruments SN65HVD78D is a 3.3 V half-duplex RS-485 transceiver with one differential driver, one differential receiver, 50 Mbps signaling, and IEC ESD protection, housed in an 8-pin SOIC package. Its 3 V to 3.6 V supply range, -40°C to +125°C operating range, and robust bus-pin protection suit demanding industrial communication systems. An RS-485 transceiver is a physical-layer interface IC that combines a differential line driver and receiver for bidirectional data transfer over a balanced bus. The half-duplex arrangement allows the same differential pair to support transmission and reception, although the design must control bus direction so that multiple drivers do not contend on the bus. Within the broader hierarchy, this device is an RS-485 interface IC, a wired-network transceiver, and a semiconductor. Key features include 50 Mbps maximum signaling, a 3.3 V nominal supply, one driver and one receiver, half-duplex operation, and enhanced ESD protection on the bus pins. The manufacturer describes protection against both Human Body Model and IEC Contact Discharge events. These characteristics distinguish the SN65HVD78D from slower RS-485 transceivers intended for lower-speed industrial multidrop networks. The combination of a differential driver and receiver on a single 3.3 V supply supports compact point-to-point and multidrop bus implementations. Half-duplex communication reduces the number of signal conductors, while the 50 Mbps capability allows the physical layer to carry high-speed command, measurement, or control traffic. The SOIC-8 package also supports conventional surface-mount assembly and is compatible with automated production equipment. Typical applications include industrial factory automation, industrial sensor and actuator networks, building-control equipment, robotics, test and measurement systems, and embedded industrial controllers. The device is especially appropriate where a 3.3 V system requires a compact, high-speed RS-485 physical layer and where exposed bus connections increase ESD risk. Designers should verify driver-enable sequencing, termination, fail-safe behavior, and signal-integrity margins against the complete bus topology. The 3.3 V supply must remain within 3 V to 3.6 V, and exposed RS-485 conductors may still require external surge and common-mode protection beyond the device's specified ESD capability. This page consolidates manufacturer information, verified distributor listings, drop-in comparison options, and practical design guidance. It distinguishes confirmed ratings from parameters that still require consultation of the complete manufacturer datasheet before production release.
SN65HVD82D - 5V RS-485 Transceiver with IEC ESD | TI
The Texas Instruments SN65HVD82D is a 5-V half-duplex RS-422/RS-485 transceiver with IEC ESD protection, offered in an 8-pin SOIC package. It combines one differential driver and one differential receiver on a single 5-V supply, making it suitable for industrial bidirectional serial networks where both transmission and reception are required on the same bus pair. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into logic levels. As a member of the RS-422 and RS-485 interface hierarchy, it supports noise-resistant, point-to-point or multipoint communication over longer cable runs than conventional single-ended interfaces. The half-duplex arrangement allows a connected node to transmit and receive, but not simultaneously, on the same pair of conductors. The SN65HVD82D operates from a single 5-V supply and supports data rates up to 250 kbps according to the available FindIC product listing. Its bus pins are designed for robust ESD event handling, with manufacturer and distributor descriptions identifying Human-Body Model, Air-Gap Discharge, Contact Discharge, and IEC ESD protection. The 8-pin SOIC package provides a conventional surface-mount form factor for industrial communication equipment. Internally, the device combines a differential driver with a differential receiver rather than implementing two unrelated interface channels. This arrangement supports bidirectional data transfer when the design uses a direction-control signal, bus multiplexing, or an application-specific enable strategy. Because RS-485 is a differential bus, correct termination, biasing, grounding, and cable routing remain central to achieving reliable communication. Typical uses include industrial sensor networks, factory automation equipment, building-control interfaces, process-monitoring systems, and communications equipment that connects a controller to remote nodes. The device is also relevant to laboratory and test systems where a compact 5-V RS-485 interface is required close to a digital controller. When laying out a board around the SN65HVD82D, place its decoupling capacitor close to the supply pins and route the differential bus as a tightly coupled pair. External protection may still be appropriate when exposed cables or severe industrial transients are expected, because integrated ESD protection does not remove the need for a correctly engineered cable and grounding system. This page combines the verified manufacturer, distributor, and cross-reference information with a practical view of package compatibility, pricing availability, ESD considerations, and application guidance. It also distinguishes verified facts from electrical details that still require confirmation in the latest manufacturer datasheet before final design release.
SN65LVDS100DGK - 2Gbps LVDS/LVPECL/CML Buffer | TI
The Texas Instruments SN65LVDS100DGK is a 2-Gbps LVDS, LVPECL and CML to LVDS buffer, repeater and level translator in an 8-pin VSSOP (DGK) package, rated for operation from -40C to +85C on a 3.3V supply. It regenerates high-speed differential data streams by connecting a high-speed differential receiver directly to a high-speed differential driver, restoring signal edge rates and amplitude on long or heavily loaded LVDS links. A differential buffer, repeater or translator is an interface IC that sits in a high-speed serial signal path: its receiver accepts one differential logic family (LVDS, PECL/LVPECL or CML) and its driver re-transmits the same data as clean LVDS. In the signal-integrity hierarchy, it sits between physical transceivers and transmission media such as backplanes, cables and clock trees, where signal degradation would otherwise exceed receiver margin. Key features include operation at signaling rates of 2 Gbps and above, low 100 ps maximum part-to-part skew, 25 mV of receiver input threshold hysteresis over a 0V to 4V common-mode input range, and positioning as a low-power alternative to the MC100EP16 ECL receiver. The wide input common-mode range allows it to accept LVPECL and CML levels while always driving a standard LVDS output. Technically, the SN65LVDS100 is formed from an input differential receiver with hysteresis followed by an LVDS output driver compliant with EIA/TIA-644 (LVDS) signaling. The device supports an additional VBB reference output of typically 1.35V below VCC, which is particularly useful for receiving single-ended 3.3V PECL inputs. Total jitter is specified for signaling rates up to 2 Gbps, and ESD tolerance exceeds 2000V per the human-body-model test referenced on the product page. Typical applications include clock distribution and jitter cleaning in networking and telecom line cards, backplane signal re-driving in industrial automation, and high-speed point-to-point links between FPGAs, ASICs and serializers where input signal quality has degraded after long traces or connectors. Design-wise, maintain a solid 3.3V supply with low-inductance 0.1uF plus 10uF decoupling, keep differential traces impedance-controlled at 100 ohms, and remember the maximum supply range of 3V to 3.6V. Place the part close to connectors to maximize the regenerated link margin. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-10-19.
SN65LVDS100DGKR - 2Gbps LVDS/LVPECL/CML Repeater | TI
The Texas Instruments SN65LVDS100DGKR is a 2-Gbps LVDS, LVPECL and CML to LVDS differential buffer, repeater and translator housed in an 8-pin VSSOP (DGK) package, rated for operation from -40C to +85C. A differential repeater is an interface IC that receives a high-speed differential signal, regenerates it through an internal receiver-driver chain, and retransmits a clean copy on the output side. In the signal-chain hierarchy, repeaters sit between the physical differential line (per EIA/TIA-644 LVDS and related PECL/CML standards) and the end receiver, restoring degraded amplitude and edge quality on long backplanes, cables, and clock-distribution networks. Key features include signaling rates up to 2 Gbps, low part-to-part skew (100 ps max class), and a built-in VBB bias output of typically 1.35 V below VCC, which lets the receiver accept single-ended 3.3 V PECL inputs directly. The device is also positioned by TI as a low-power alternative to the MC100EP16 ECL buffer, and is qualified for automotive applications. Inside, a high-speed differential receiver with input hysteresis accepts LVDS, LVPECL, or CML levels and drives an LVDS-compliant differential output, effectively decoupling the transmit side from input-level variations. This level translation removes the need for external bias networks or level-shifting discretes, reducing BOM count and jitter contribution compared with cascaded discrete buffers. Typical applications include clock and data signal regeneration in telecom and networking line cards, PCIe/serial-link signal integrity recovery on long PCB traces, and test-and-measurement signal distribution where 2-Gbps edges must be preserved. The automotive qualification also supports infotainment and camera-link repeater use. For design, decouple VCC with at least 0.1 uF ceramic capacitors close to the supply pins, route the differential pair with controlled impedance (100 ohm LVDS), and keep the VBB bypass path quiet for single-ended PECL use. This page synthesizes distributor pricing (LCSC, DigiKey, Mouser), drop-in same-package alternatives, and design notes that go beyond the raw datasheet parameters.
SN65LVDS100DGKRG4 - 2Gbps LVDS Repeater | TI | VSSOP-8
The Texas Instruments SN65LVDS100DGKRG4 is a 2 Gbps LVDS/LVPECL/CML-to-LVDS differential repeater and translator in an 8-pin VSSOP (DGK) package. It regenerates high-speed differential signals with only 65 ps of total jitter, making it a clean-signal solution for long backplane or cable runs. A differential repeater is a signal-conditioning device placed in a high-speed serial link: it receives a degraded differential waveform, re-amplifies and re-times it through a receiver-driver pair, and launches a fresh LVDS signal onto the next segment. In the signal-integrity hierarchy it sits between a plain buffer and a full retimer, belonging to the broader family of interface ICs and signal buffers/repeaters. Key features include signaling rates up to 2 Gbps, low 100 ps maximum part-to-part skew, receiver input threshold hysteresis for noise rejection, and a wide input common-mode range that accepts LVDS, PECL, and CML signal levels. TI positions it as a low-power alternative to the MC100EP16 ECL repeater, offering significant static current savings in LVDS mode. The input receiver tolerates a broad common-mode range, so designers can AC-couple or DC-couple LVPECL and CML sources with simple biasing. The output drives a nominally 100-ohm differential transmission line with standard LVDS levels. The signal path is always-on: power is roughly the sum of receiver and driver currents, and the DGK package junction-to-ambient thermal resistance comfortably handles the sub-100 mW dissipation. Typical applications include clock distribution and fan-out in telecom line cards, redriving LVDS signals across backplanes and cable interconnects, and translating PECL or CML outputs to LVDS-compatible receivers in test instrumentation and imaging systems. For design, keep the 100-ohm differential impedance continuous through the device; place the part at the midpoint of lossy traces where the eye is still open enough to meet the receiver threshold. AC-coupled PECL inputs require appropriate bias resistors per the TI datasheet application section. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.
SN65LVDS22DR - Dual Multiplexed LVDS Repeater 250Mbps | TI
The Texas Instruments SN65LVDS22DR is a dual multiplexed LVDS repeater that supports clock rates to 200 MHz (400 Mbps) and data rates to 250 Mbps, operates from a single 3.3 V supply, and is housed in a 16-pin SOIC (D) package. An LVDS (Low-Voltage Differential Signaling) repeater is an interface buffer that regenerates and redistributes differential signal pairs, restoring signal amplitude and edge quality degraded by long backplanes, cables, or multiple loads. As a member of the broader voltage-mode driver and interface IC family, an LVDS repeater sits between a differential transmitter and receiver in the signal chain hierarchy, isolating loading effects and enabling fan-out of a single LVDS source to multiple destinations without signal degradation. Key features include ANSI TIA/EIA-644-1995 standard compliance, LVDS output voltages of 350 mV into a 100-ohm load, and a typical propagation delay of 4 ns. ESD protection exceeds 12 kV on bus pins and exceeds 2000 V per MIL-STD-883, Method 3015 (HBM), with machine-model protection exceeding 200 V (200 pF, 0 ohm). The device is pin compatible with the SN65LVDS122 and SN65LVDT122 1.5 Gbps 2x2 crosspoint switches from TI, providing a direct speed-upgrade path. The multiplexed 1x2:2 architecture allows each LVDS input to be selectively routed or repeated, giving system designers flexible signal-distribution topologies. Low differential output swing (typically 350 mV) minimizes EMI and power consumption compared with older differential standards, while the 4 ns propagation delay keeps timing budgets small even at 250 Mbps data rates. Typical applications include backplane signal buffering in industrial control systems, clock distribution in telecom and datacom line cards, and LVDS signal fan-out in automotive communication modules, where the device is qualified for automotive applications. Design considerations: TI specifies the SN65LVDS22 (100-ohm load) and SN65LVDM22 (50-ohm load) as load-specific variants, so select the termination impedance variant to match the bus. When more bandwidth is needed, drop in the pin-compatible SN65LVDS122/SN65LVDT122 for up to 1.5 Gbps operation. This page synthesizes distributor availability, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.
SN65LVDT100DGKR - 2Gbps LVDS Repeater/Translator | Texas Instruments
The Texas Instruments SN65LVDT100DGKR is a 2-Gbps LVDS, LVPECL and CML to LVDS differential repeater/translator housed in an 8-pin VSSOP (DGK) package, rated for operation from -40C to +85C. It accepts LVDS, PECL or CML input signals at signaling rates up to 2 Gbps and repeats them as LVDS output levels on a 3.3-V supply. A differential repeater/translator is an interface IC that regenerates high-speed differential signals degraded by long transmission lines, connectors or backplanes. Within the signal-chain hierarchy, it sits between physical transceivers and their serializers or receivers: the device receives a differential waveform, squares its edges, and re-drives it with clean LVDS levels, extending the achievable link distance beyond what a plain transceiver can reach. Key features include a 2-Gbps maximum signaling rate, low total jitter (less than 65 ps per the device overview), maximum 100-ps part-to-part skew, and an integrated 110-ohm differential line-termination resistor. The on-chip termination reduces board space, component count and stub length compared with external resistor networks. The receiver input threshold hysteresis further improves noise immunity on marginal differential links. The architecture combines a high-speed differential receiver with an LVDS driver connected as a repeater. TI positions the SN65LVDT100 as a low-power alternative for the MC100EP16, while adding signal reconditioning. The integrated 7-V protected output structure tolerates hot-swap-style line conditions, and the wide input-format acceptance (LVDS/LVPECL/CML) removes the need for level-shifting front ends in mixed-logic designs. Typical applications include LVDS LCD panel links needing extra cable reach (as discussed in TI's E2E interface forum for 5-m cable runs), backplane and rack-to-rack differential clock or data distribution, and generic 2-Gbps signal reconditioning in telecommunications, industrial imaging and test equipment. When designing with this device, keep the 110-ohm integrated termination in mind when matching it to cables or boards whose characteristic impedance differs significantly from 100 ohms, and minimize stub length by placing the part directly at the connector. This page adds distributor pricing context, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing references marked as of 2026-10-19.
SN74AVC4T245QWRGYRQ1 - 4-Bit Dual-Supply Level Shifter AEC-Q100 | TI
The Texas Instruments SN74AVC4T245QWRGYRQ1 is an automotive-grade, 4-bit dual-supply bus transceiver with configurable voltage-level translation and 3-state outputs, packaged in a compact 16-pin VQFN (RGY, 4x3.5 mm) footprint. It enables bidirectional level shifting between buses operating at different supply voltages and is AEC-Q100 qualified for automotive use. A bus transceiver is a digital interface IC that combines transmit and receive paths in one device, allowing bidirectional data flow between two buses. The SN74AVC4T245-Q1 belongs to the voltage-level translator family, a subset of interface ICs within the broader integrated circuits category. Level translation is essential when connecting components with different I/O voltages, such as a 1.8 V microcontroller interfacing with a 3.3 V peripheral. Key features include dual-supply operation with VCCA and VCCB each accepting 1.2 V to 3.6 V, tri-state outputs for bus isolation, and Ioff partial-power-down protection that disables outputs and prevents damaging backflow current when either supply is removed. A typical propagation delay of 2.1 ns and data rates up to 380 Mbps make the device suitable for SPI, I2C, UART, and parallel GPIO interfaces. The CMOS architecture supports use as two independent 2-bit transceivers or one 4-bit transceiver. Direction control (1DIR, 2DIR) and output-enable (1OE, 2OE) pins are referenced to VCCA, simplifying control-logic design in mixed-voltage systems. The device operates asynchronously, requiring no clock signal, and is fully specified over the -40C to +125C automotive temperature range. Typical applications include automotive body control modules, ADAS ECUs, infotainment systems, and industrial automation. In ECUs, it bridges 1.8 V or 2.5 V MCUs to 3.3 V sensors, CAN transceiver interfaces, SPI flash, and general-purpose GPIO level shifting. Site-available companions include the SN65HVD230QDRQ1 CAN transceiver and SN74LVC1T45QDCKRQ1 single-bit translator. Design tip: decouple VCCA and VCCB with 0.1 uF capacitors placed close to the pins, and ensure DIR/OE signals (VCCA domain) are stable before data transmission to avoid bus contention.
SN75112N - Dual 2/0 Line Driver | Texas Instruments
Texas Instruments SN75112N is a dual differential line driver with two drivers and no receiver channels, supplied in a 14-pin PDIP package. The device is designed for improved output-current regulation across supply-voltage and temperature changes, providing constant-current outputs, high speed, high output impedance, TTL-compatible inputs, and a common-mode output-voltage range extending from -3 V to 10 V. A line driver is an interface IC that converts logic-level input signals into stronger, differential outputs suitable for driving balanced cables or bus links. Within the interface-IC hierarchy, a dual line driver occupies the transmitter side of a communications interface. It accepts TTL-compatible control signals and uses two output channels to support applications such as V.35 data-interchange circuits when paired with an appropriate receiver and external components. Key benefits include improved stability over supply-voltage and temperature ranges, constant-current outputs, high operating speed, standard supply voltages, and high output impedance. The high output impedance helps limit loading of the driven line, while the constant-current behavior improves control of output current as voltage and temperature change. An inhibitor input is available for driver shutdown control. The SN75112 family is specifically referenced by Texas Instruments for implementing V.35 data-interchange circuits with the SN75107A dual line receiver and suitable external resistors. Its two independent channels can also support general-purpose balanced signaling, clock distribution, test equipment, industrial control links, and legacy communications interfaces where TTL inputs and differential outputs are required. Designers should verify the exact supply-voltage limits, output-current limits, propagation delays, input thresholds, and operating-temperature range against the manufacturer datasheet before finalizing a circuit. PCB layout should keep each driver channel's output path compact, provide a common return reference, and avoid routing sensitive differential signals beside unrelated high-current switching nodes. This page combines manufacturer product information, interface and package details, application guidance, and drop-in replacement findings. It also provides actionable design notes and a specification-oriented comparison framework for engineers evaluating SN75112N in new and legacy interface designs.
SN75117P - 5V Differential Line Transceiver | Texas Instruments
The Texas Instruments SN75117P is a 5 V differential line transceiver combining one driver and one receiver in an 8-pin PDIP package. It provides TTL-compatible driver inputs, TTL-compatible receiver outputs, three-state driver output circuitry, and a receiver output strobe for party-line or bus-organized systems. According to the manufacturer datasheet, the family also supports optional line termination through an internal 130-ohm equivalent resistor. A differential line transceiver is an interface circuit that translates digital logic signals between a TTL-compatible system and a differential transmission line. The transmitter converts a single-ended logic input into a differential line signal, while the receiver converts the differential signal back into a single-ended TTL-compatible output. This interface hierarchy belongs to the broader class of bus transceivers, which connect digital logic ICs to communication lines. The SN75117P is intended for bus-organized equipment where multiple transceivers can share a common line. Its three-state driver permits the driver output to be electrically disabled when another node must transmit, helping prevent bus contention when system control is correctly coordinated. The strobe control provides a way to control when the receiver output is presented to the connected logic circuit. The implementation combines a single 5 V supply with bipolar differential line-driver and receiver functions. A listed propagation-delay value of 75 ns supports moderate-speed party-line data transfer, while the receiver-side frequency-response control permits system designers to trade response speed for improved differential noise immunity. The internal line-termination option helps control reflections on suitably designed cables or PCB interconnects. Typical uses include industrial data buses, controller networks, test equipment, and embedded systems that need a compact TTL-to-differential interface. The device can also participate in multi-drop arrangements where node enable control is coordinated by host logic. For systems using complementary RS-485 transceivers, the interface functions remain functionally related, but modern devices may add fail-safe behavior and stronger electrostatic-discharge protection. When laying out a board, place the transceiver near the line connector and keep the differential route short, balanced, and away from switching nodes. Confirm that enable and strobe timing cannot place two drivers on the bus simultaneously. Select external termination values from the actual cable impedance and topology rather than enabling every termination option by default. This page combines the SN75117P interface characteristics, package information, replacement considerations, and practical bus-design guidance into a focused engineering reference. It also identifies the verified family relationship used for the available drop-in alternative and highlights functional differences that must be checked before board reuse.
SN75123N - Dual TTL Line Driver | Texas Instruments
Texas Instruments SN75123N is a dual line driver designed for IBM System 360 input/output interfaces, standard TTL logic, and terminated coaxial-cable or twisted-pair lines. The device operates from a single 5 V supply, provides TTL-compatible inputs and outputs, and is offered in a 16-pin PDIP package. Its output stage reaches 3.11 V at a source current of -59.3 mA. A line driver is a digital interface circuit that converts a logic-level input into a stronger output capable of driving a transmission line. The SN75123 belongs to the broader logic IC and interface IC hierarchy. Its low-impedance emitter-follower outputs provide bidirectional signal transfer into terminated lines, while the uncommitted output structure permits multiple drivers to share a party-line bus for wired-OR operation. The principal benefits are the combination of dual-channel drive capability, standard-TTL compatibility, a single 5 V supply, and low-impedance emitter-follower outputs. The 3.11 V output level at -59.3 mA provides a concrete indication of the output drive capability. Because both channels share the same package and supply architecture, the SN75123N can serve dual-ended, paired, or independently terminated line-driver arrangements where TTL logic must interface with older computer-bus or communications equipment. Technically, the emitter-follower architecture makes the output suitable for coax or twisted-pair termination rather than providing an actively isolated differential output. The uncommitted outputs support party-line operation, allowing several drivers to be connected to one line when only one channel is active at a time. Designers must ensure that inactive outputs are held in a defined state so that no driver contends with another device on the shared bus. Typical applications include legacy computer-interface equipment, point-to-point coax links, twisted-pair links, instrumentation interfaces, and industrial control systems that use 5 V TTL signaling. The SN75123N is particularly relevant when upgrading or maintaining equipment designed around IBM System 360-era interface levels while retaining modern solid-state control logic. For a new design, verify the complete pin assignment, output-state requirements, termination topology, and timing margins in the manufacturer datasheet before layout. If the board uses two separate line interfaces, place the device close enough to the line-driver circuitry to minimize exposure to coupled noise. A terminating network at the receiving end is generally required for reliable operation over longer cable runs. This product guide combines the electrical function, package information, interface use cases, pinout-reference guidance, design cautions, and available replacement context. It also distinguishes the confirmed TTL and line-drive characteristics from parameters that require direct confirmation in the Texas Instruments documentation before a production design is released.