Interface ICs
ژێرپۆلەکان
بەرهەمەکان (560+)
SN75150D - Dual RS-232 Line Driver | Texas Instruments
The Texas Instruments SN75150D is a monolithic dual RS-232 line driver designed for data-terminal equipment and data-communication equipment interfaces defined by TIA/EIA-232-F. It provides two transmit channels in an 8-pin SOIC package and supports transmission at 20 kbit/s with a full 2500-pF load. The device uses positive and negative supply rails, and its TTL-compatible logic inputs make it suitable for interfacing with many standard logic families. A line driver is an interface IC that converts digital logic-level signals into differential or bipolar signaling suitable for transmission over a communication cable. The SN75150 belongs to the broader RS-232 interface family, alongside line receivers and combined transceiver devices. It is intended for point-to-point data transmission, level translation, and driving MOS-device inputs where a stronger, polarity-aware output signal is useful. The principal features of the SN75150D include two independent driver outputs, support for the TIA/EIA-232-F interface requirements, a stated transmission rate of 20 kbit/s with a full 2500-pF load, and operation from 12-V and -12-V supplies. The logic input is compatible with most TTL families. The manufacturer product page also identifies data-transmission systems using relatively short single lines, level translators, and MOS-device drivers as additional applications. The SN75150D is a transmit-only device. It does not include an RS-232 receiver, so a complete bidirectional RS-232 link requires a separate receiver IC or transceiver. This distinction matters when allocating connectors and signal paths: each transmit signal is driven by the SN75150D, while incoming signals must be routed to a suitable receiver. The SOIC-8 package also makes the device appropriate for conventional surface-mount PCB assembly rather than through-hole insertion. Typical deployments include serial console links, industrial equipment interfaces, short-distance data-transfer systems, and level-conversion circuits between TTL logic and bipolar RS-232 equipment. Because the driver is designed for relatively short single lines, cable length, load capacitance, grounding, and signal integrity should be checked against the interface requirements rather than treated as unlimited-distance links. When laying out the circuit, place the SN75150D close to the connector or protected interface boundary and route the RS-232 outputs away from sensitive analog and clock signals. Confirm both positive and negative supply rails are present, and ensure downstream receivers are not driven beyond their permitted input limits. The absence of an integrated receiver means system-level communication requires coordinated driver and receiver selection. This product page organizes the manufacturer specifications, interface role, sourcing information, application guidance, and design considerations into a practical engineering reference for the SN75150D.
SN75159D - Dual RS-422 Driver, 5 V, 14-SOIC | Texas Instruments
Texas Instruments SN75159D is a dual differential line driver with 3-state outputs, a 5 V single-supply rating, and a 14-pin SOIC package. The device provides two balanced driver channels designed for RS-422 and related differential signaling systems. Its high-impedance output state supports party-line and shared-bus arrangements where multiple transmitters must be connected to the same physical line. A differential line driver is a digital interface IC that converts a pair of complementary TTL-compatible logic signals into a balanced differential output. This signaling method reduces sensitivity to common-mode noise compared with single-ended transmission. The SN75159 family supports balanced point-to-point and multidrop interfaces associated with ANSI EIA/TIA-422-B and ITU Recommendation V.11 applications, as identified in the manufacturer documentation. The principal features of the SN75159D are its dual-driver configuration, balanced differential outputs, 3-state output control, single 5 V supply operation, and TTL-compatible inputs. The 3-state behavior allows each driver channel to be disconnected electrically when inactive. This is useful in party-line systems because multiple transmitters can share a bus without preventing other channels from communicating when their output-enable controls are inactive. The SN75159D is a line-driver rather than a line receiver. Data is driven from the logic side toward a balanced cable or board-level transmission path, while a separate receiver IC converts the differential signal back into logic levels at the destination. Using a transmitter and receiver that implement compatible RS-422 signaling helps maintain consistent voltage thresholds, impedance behavior, and common-mode limits across the link. Typical uses include industrial data acquisition, test and measurement systems, communications equipment, instrumentation interfaces, computer peripherals, and other systems that transmit digital information over a balanced differential connection. Cable length, data rate, termination, grounding, and receiver selection remain system-level constraints. Differential routing should use a controlled impedance and a grounded reference where practical to preserve signal integrity. When laying out a circuit using the SN75159D, place the device near the line-driver interface, keep the differential pair tightly matched, and provide a clear return path. Account for connector and cable reflections with the termination strategy recommended for the selected communication standard. Enable and disable sequencing should also ensure that only the intended transmitter drives the shared bus. This page consolidates the SN75159D interface function, package information, sourcing workflow, application guidance, and engineering checks into a concise selection reference. It also identifies which device details still require confirmation from the manufacturer datasheet before a new layout is released for production.
SN75174DW - 4-Channel RS-422/RS-485 Driver | Texas Instruments
The Texas Instruments SN75174DW is a monolithic quadruple differential line driver with four independently enabled, three-state outputs, a 4.75 V to 5.25 V supply range, and operation up to 4 megabaud in a 20-pin SOIC package. It meets the requirements of ANSI EIA/TIA-422-B, RS-485, and ITU Recommendation V.11. A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs for communication over cables or long printed-circuit-board traces. As a member of the RS-422 and RS-485 interface hierarchy, it translates a digital transmitter signal into noise-resistant differential voltage pairs. The four channels suit multipoint buses, industrial equipment, industrial-control systems, and legacy data ports where multiple bus nodes require controlled output states. The SN75174 provides four differential drivers and common enable and ground pins. Each driver uses a positive and negative output, while the three-state outputs support shared party-line buses by placing unused transmitters in a high-impedance state. Its balanced outputs reduce sensitivity to common-mode noise, and the wide positive and negative output common-mode voltage ranges make it suitable for noisy industrial environments. The device supports transmission rates up to 4 megabaud and is intended for balanced multipoint communication. This makes it appropriate for RS-422 and RS-485 systems where a transmitter must support multiple drivers on one bus. The common enable control can coordinate output states, but system design must prevent multiple drivers from actively driving the same pair simultaneously. Typical uses include industrial RS-485 buses, data acquisition equipment, telecommunications interfaces, instrumentation, computer peripherals, and embedded control systems. The 20-pin SOIC package supports conventional surface-mount assembly and is available as the SN75174DW ordering option identified by DigiKey as a 20-SOIC device. Designers should match cable termination, biasing, and transceiver direction-control requirements to the bus standard. Keep traces short where possible, provide a continuous ground reference where the interface standard permits it, and verify signal polarity and enable timing before enabling the outputs. The SN75174DW is a digital interface IC, so Safe Operating Area data do not apply.
SN75174DWR - 4-Channel RS-422/RS-485 Driver | Texas Instruments (Tape & Reel)
The Texas Instruments SN75174DWR is a monolithic quadruple differential line driver with four independently enabled, three-state outputs, a 4.75 V to 5.25 V supply range, and operation up to 4 megabaud in a 20-pin SOIC package. It meets the requirements of ANSI EIA/TIA-422-B, RS-485, and ITU Recommendation V.11. A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs for communication over cables or long printed-circuit-board traces. As a member of the RS-422 and RS-485 interface hierarchy, it translates a digital transmitter signal into noise-resistant differential voltage pairs. The four channels suit multipoint buses, industrial equipment, industrial-control systems, and legacy data ports where multiple bus nodes require controlled output states. The SN75174 provides four differential drivers and common enable and ground pins. Each driver uses a positive and negative output, while the three-state outputs support shared party-line buses by placing unused transmitters in a high-impedance state. Its balanced outputs reduce sensitivity to common-mode noise, and the wide positive and negative output common-mode voltage ranges make it suitable for noisy industrial environments. The device supports transmission rates up to 4 megabaud and is intended for balanced multipoint communication. This makes it appropriate for RS-422 and RS-485 systems where a transmitter must support multiple drivers on one bus. The common enable control can coordinate output states, but system design must prevent multiple drivers from actively driving the same pair simultaneously. Typical uses include industrial RS-485 buses, data acquisition equipment, telecommunications interfaces, instrumentation, computer peripherals, and embedded control systems. The 20-pin SOIC package supports conventional surface-mount assembly and is available as the SN75174DWR ordering option identified by DigiKey as a 20-SOIC device. Designers should match cable termination, biasing, and transceiver direction-control requirements to the bus standard. Keep traces short where possible, provide a continuous ground reference where the interface standard permits it, and verify signal polarity and enable timing before enabling the outputs. The SN75174DWR is a digital interface IC, so Safe Operating Area data do not apply.
SN75176ADR - RS-422/RS-485 Differential Bus Transceiver | Texas Instruments
The Texas Instruments SN75176ADR is a differential bus transceiver for bidirectional RS-422 and RS-485 communication, supplied in an 8-pin SOIC package. It combines a differential line driver with a differential receiver and supports multipoint transmission over long bus lines in noisy environments. The verified product information identifies the device as an RS-422/RS-485 interface IC with a 4.75 V to 5.25 V supply range and 3-state driver and receiver outputs. The transceiver is designed for balanced transmission lines and is reported to meet ANSI Standard EIA/TIA-422-B and ITU Recommendation V.11 requirements. SN75176ADR is the Texas Instruments orderable part number associated with the SN75176A family. The SOIC-8 package supports conventional surface-mount assembly and is suitable for industrial communication, data acquisition, factory automation, and embedded serial-interface designs. The device architecture allows the same physical bus interface to support both transmitting and receiving differential data, while the 3-state outputs permit multiple drivers to share a bus when the enable control is inactive. Its differential signaling helps reject common-mode noise present in industrial environments and reduces susceptibility to ground-potential differences between connected equipment. When designing a replacement or new board around SN75176ADR, verify the logic polarity of the receiver-enable and driver-enable controls, the termination strategy, the bus biasing arrangement, and the operating voltage at every connected node. The compact SOIC-8 footprint is widely supported by PCB libraries and compatible transceiver families. This page combines verified distributor pricing, interface standards, replacement information, and practical RS-485 design guidance.
SP232ECN-L - ±15kV ESD 5V RS-232 IC | MaxLinear
The MaxLinear SP232ECN-L is a 5 V, single-supply RS-232 line transceiver with two drivers and two receivers, enhanced ±15 kV ESD protection, and a 16-pin SOIC package. It is designed for dual-channel serial-interface equipment operating from 4.5 V to 5.5 V, with an industrial temperature option identified by the supplied distributor data as 0°C to 70°C. An RS-232 transceiver is a line-interface IC that combines digital-to-analog transmit drivers with analog-to-digital receive inputs. The SP232ECN-L belongs to the RS-232 interface family, which connects TTL/CMOS logic to the charge-balanced, bipolar signaling used by RS-232 ports. Its two drivers and two receivers support two serial channels in one package. The principal verified features include operation from a single +5 V supply, compatibility with RS-232 and V.28 protocols, 2/2 transceiver organization, and enhanced ESD tolerance identified in the supplied search results as ±15 kV. The device is available from the verified distributor pages in a 16-pin SOIC package, and the results describe it as a CMOS line transceiver with TTL-compatible interfacing. The SP232ECN-L is suitable for industrial and embedded systems that need a compact, dual-channel RS-232 port without a separate driver and receiver IC for each direction. Typical uses include service-console interfaces, configuration ports, instrumentation, and control equipment. Its integrated 2/2 organization reduces board area and simplifies firmware allocation compared with separate single-channel devices, while the single +5 V supply simplifies system power design. For layout, place the transceiver close to the connector and route driver outputs and receiver inputs as a protected differential class rather than as ordinary low-speed logic nets. Keep the external protection-network and bypass-capacitor loops compact, observe the datasheet’s recommended capacitor and grounding arrangements, and verify the selected package’s pin numbering before PCB release. The SP232ECN-L is a wired serial-interface device, so its cable length, grounding, shielding, and protection strategy must be designed with the complete RS-232 system in mind. This page combines verified distributor identifiers, package information, protocol references, temperature information, and drop-in replacement context to support component selection. Exact pricing, electrical timing values, pin-level details, lifecycle status, and manufacturer compliance declarations were not present in the supplied verified data and are therefore not guessed here.
SP232ECN-L/TR - ±15kV ESD 5V RS-232 IC | MaxLinear (Tape & Reel)
The MaxLinear SP232ECN-L/TR is a 5 V, single-supply RS-232 line transceiver with two drivers and two receivers, enhanced ±15 kV ESD protection, and a 16-pin SOIC package. It is designed for dual-channel serial-interface equipment operating from 4.5 V to 5.5 V, with an industrial temperature option identified by the supplied distributor data as 0°C to 70°C. An RS-232 transceiver is a line-interface IC that combines digital-to-analog transmit drivers with analog-to-digital receive inputs. The SP232ECN-L/TR belongs to the RS-232 interface family, which connects TTL/CMOS logic to the charge-balanced, bipolar signaling used by RS-232 ports. Its two drivers and two receivers support two serial channels in one package. The principal verified features include operation from a single +5 V supply, compatibility with RS-232 and V.28 protocols, 2/2 transceiver organization, and enhanced ESD tolerance identified in the supplied search results as ±15 kV. The device is available from the verified distributor pages in a 16-pin SOIC package, and the results describe it as a CMOS line transceiver with TTL-compatible interfacing. The SP232ECN-L/TR is suitable for industrial and embedded systems that need a compact, dual-channel RS-232 port without a separate driver and receiver IC for each direction. Typical uses include service-console interfaces, configuration ports, instrumentation, and control equipment. Its integrated 2/2 organization reduces board area and simplifies firmware allocation compared with separate single-channel devices, while the single +5 V supply simplifies system power design. For layout, place the transceiver close to the connector and route driver outputs and receiver inputs as a protected differential class rather than as ordinary low-speed logic nets. Keep the external protection-network and bypass-capacitor loops compact, observe the datasheet’s recommended capacitor and grounding arrangements, and verify the selected package’s pin numbering before PCB release. The SP232ECN-L/TR is a wired serial-interface device, so its cable length, grounding, shielding, and protection strategy must be designed with the complete RS-232 system in mind. This page combines verified distributor identifiers, package information, protocol references, temperature information, and drop-in replacement context to support component selection. Exact pricing, electrical timing values, pin-level details, lifecycle status, and manufacturer compliance declarations were not present in the supplied verified data and are therefore not guessed here.
SP3232EUEA-L - 1 Mbps RS-232 Transceiver | MaxLinear (Tape & Reel)
The MaxLinear SP3232EUEA-L is a 3.3 V RS-232 transceiver with two drivers and two receivers, a maximum data rate of 1000 kbps, and a 16-SSOP package. Designed for portable and embedded systems, it combines bidirectional RS-232 signal conditioning with an integrated charge-pump supply that supports operation from a single low-voltage source. The SP3232EU family is specifically positioned for notebook, palmtop, industrial, and instrument applications requiring reliable serial communication without a separate external RS-232 supply. An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into RS-232-compatible voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, it is a physical-layer transceiver: logic ICs and microcontrollers generate the data, while the SP3232EUEA-L handles voltage translation, noise margin, and line-driver capability. Two drivers and two receivers support two communication channels or paired full-duplex links. The SP3232EUEA-L operates at 3.3 V and supports a maximum data transmission rate of 1000 kbps. Its high-efficiency charge-pump supply requires only 0.1 µF capacitors for 3.3 V operation, reducing the external component count compared with conventional RS-232 designs that use larger pump capacitors. The integrated drivers and receivers also reduce board area while preserving separate transmit and receive paths. The device is packaged in a 16-SSOP and supplied in tape-and-reel packaging for automated assembly. The -L/TR ordering form identifies the leaded 16-pin package and tape-and-reel shipment configuration. Its interface architecture is suitable for compact control panels, portable test equipment, configuration ports, and service interfaces where a legacy RS-232 connector must connect to a modern low-voltage UART. Typical applications include notebook-style service connections, industrial controller diagnostics, laboratory instrument control, point-of-sale equipment, and embedded debug interfaces. The 1000 kbps capability allows the transceiver to handle substantially faster data than a conventional low-speed RS-232 port, provided that the UART, cable, connector, and system timing are designed for the selected baud rate. When laying out the circuit, place the charge-pump capacitors and transceiver interface components close to their associated pins. Route the RS-232 driver and receiver traces away from sensitive clock, sensor, and analog inputs. Confirm the logic-side supply level, UART signal polarity, and connector pin assignment before power-up because a wiring error at the RS-232 connector can defeat otherwise correct logic-side communication. This page organizes the manufacturer specifications, sourcing information, same-package family alternatives, and practical interface-layout guidance into one engineering-focused reference. It also distinguishes verified device facts from parameters that require confirmation against the complete manufacturer datasheet and the specific PCB implementation.
SP3232EUEA-L/TR - 1 Mbps RS-232 Transceiver | MaxLinear
The MaxLinear SP3232EUEA-L/TR is a 3.3 V RS-232 transceiver with two drivers and two receivers, a maximum data rate of 1000 kbps, and a 16-SSOP package. Designed for portable and embedded systems, it combines bidirectional RS-232 signal conditioning with an integrated charge-pump supply that supports operation from a single low-voltage source. The SP3232EU family is specifically positioned for notebook, palmtop, industrial, and instrument applications requiring reliable serial communication without a separate external RS-232 supply. An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into RS-232-compatible voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, it is a physical-layer transceiver: logic ICs and microcontrollers generate the data, while the SP3232EUEA-L/TR handles voltage translation, noise margin, and line-driver capability. Two drivers and two receivers support two communication channels or paired full-duplex links. The SP3232EUEA-L/TR operates at 3.3 V and supports a maximum data transmission rate of 1000 kbps. Its high-efficiency charge-pump supply requires only 0.1 µF capacitors for 3.3 V operation, reducing the external component count compared with conventional RS-232 designs that use larger pump capacitors. The integrated drivers and receivers also reduce board area while preserving separate transmit and receive paths. The device is packaged in a 16-SSOP and supplied in tape-and-reel packaging for automated assembly. The -L/TR ordering form identifies the leaded 16-pin package and tape-and-reel shipment configuration. Its interface architecture is suitable for compact control panels, portable test equipment, configuration ports, and service interfaces where a legacy RS-232 connector must connect to a modern low-voltage UART. Typical applications include notebook-style service connections, industrial controller diagnostics, laboratory instrument control, point-of-sale equipment, and embedded debug interfaces. The 1000 kbps capability allows the transceiver to handle substantially faster data than a conventional low-speed RS-232 port, provided that the UART, cable, connector, and system timing are designed for the selected baud rate. When laying out the circuit, place the charge-pump capacitors and transceiver interface components close to their associated pins. Route the RS-232 driver and receiver traces away from sensitive clock, sensor, and analog inputs. Confirm the logic-side supply level, UART signal polarity, and connector pin assignment before power-up because a wiring error at the RS-232 connector can defeat otherwise correct logic-side communication. This page organizes the manufacturer specifications, sourcing information, same-package family alternatives, and practical interface-layout guidance into one engineering-focused reference. It also distinguishes verified device facts from parameters that require confirmation against the complete manufacturer datasheet and the specific PCB implementation.
SP485ECP-L - RS-485 Transceiver | Exar | Industrial Communication
The SP485ECP-L is a single-channel RS-485 transceiver from Exar, designed for bidirectional serial communication over long industrial, instrumentation, and building-automation cables. It combines a differential line driver and receiver in an 8-pin SOIC package, making it suitable for systems that require robust communication with a low component count and a compact board footprint. The verified web data for this MPN did not include manufacturer specifications, pricing, pinout details, or alternative cross-reference results, so specific electrical values are marked as data needed rather than estimated. An RS-485 transceiver is a physical-layer interface device that converts logic-level digital signals into balanced differential signals and receives those differential signals back as digital data. Its differential signaling improves noise immunity and allows communication across longer cable runs than conventional single-ended interfaces. The SP485ECP-L family is commonly associated with industrial RS-485 networks, but the exact electrical ratings, data rate, operating temperature, and package variant for SP485ECP-L must be confirmed against the manufacturer datasheet before release to production. The device is intended for applications such as industrial sensor networks, motor-control equipment, factory automation, building controls, remote instrumentation, and embedded serial links. In a typical circuit, the transceiver interfaces a microcontroller UART to a two-wire differential bus. The design must account for bus termination, fail-safe biasing, common-mode range, cable length, node count, and grounding. An integrated transceiver simplifies the physical layer, but it does not replace application-level protection or network design. Because the supplied verified dataset contains no successful search results, no confirmed distributor pricing, and no verified alternative entries, this page preserves uncertainty explicitly. The alternatives listed below are same-brand family references identified from permitted parametric knowledge and should be treated as engineering candidates, not as confirmed substitutes. Verify package marking, pinout, speed grade, temperature range, and electrical limits before substitution. The most important design practice is to treat the RS-485 network as a controlled transmission-line system. Use the correct termination at physical endpoints, provide a suitable common-mode strategy, and isolate the bus when surge or ground-potential hazards are possible. A separate transceiver can improve throughput and simplify firmware, but its RS-485 driver characteristics, propagation delay, and fault tolerance determine the practical maximum network performance.
ST1480ACDR - 3.3V RS-485/RS-422 Transceiver | STMicroelectronics
The ST1480ACDR is a low-power, half-duplex RS-485/RS-422 transceiver from STMicroelectronics, designed for balanced data transmission in industrial and instrumentation applications. It operates from a single 3.3V supply and supports data rates up to 12 Mbps, making it suitable for high-speed communication networks. The device is available in the industry-standard SOIC-8 package, ensuring easy integration into existing designs. An RS-485 transceiver is a line driver and receiver pair that enables robust differential data communication over long distances and in noisy environments. It converts TTL/CMOS logic levels to differential signals on a twisted-pair bus, allowing multiple devices to share the same wiring. RS-485 is a physical layer standard defined by the TIA/EIA-485 specification, widely used in industrial automation, building control, and networking. The ST1480ACDR implements this standard with a 3.3V supply, reducing power consumption compared to 5V counterparts while maintaining compatibility with 5V logic through its fail-safe receiver. Key features of the ST1480ACDR include a wide common-mode input range of -7V to +12V, which enhances noise immunity and allows operation in harsh industrial environments. The device features a 1/8 unit load, allowing up to 256 transceivers on a single bus, and includes thermal shutdown and short-circuit protection for robust operation. Its low quiescent current of 900 uA makes it ideal for power-sensitive applications. The ST1480ACDR uses a standard RS-485 architecture with a differential driver and receiver, featuring a tri-state output for half-duplex operation. The receiver has a fail-safe design that ensures a high output when the inputs are open, shorted, or terminated, preventing false data. The driver is capable of delivering up to 60 mA of output current, meeting the RS-485 standard's minimum requirement of 1.5V differential output across a 54-ohm load. Typical applications include industrial control networks, building automation, HVAC systems, and point-of-sale terminals. Its high data rate and robust ESD protection (8 kV HBM) make it suitable for factory automation and process control. The device is also used in security systems and remote sensor networks where reliable long-distance communication is critical. When designing with the ST1480ACDR, ensure proper termination (120-ohm) at both ends of the bus to minimize reflections. The fail-safe receiver feature eliminates the need for external bias resistors in most applications, simplifying the design. For half-duplex operation, control the driver enable (DE) and receiver enable (RE) pins to avoid bus contention.
ST202BDR - 5V RS-232 Transceiver 2D/2R | STMicroelectronics
The STMicroelectronics ST202BDR is a 2-driver, 2-receiver RS-232 transceiver operating from a single 5 V supply (4.5 V to 5.5 V range) with a 400 kbps data rate and ±30 V receiver input tolerance, housed in a 16-pin SOIC (SO-16) surface-mount package. An RS-232 transceiver is an interface IC that translates logic-level serial signals (TTL/CMOS, 0 V to 5 V) into the EIA/TIA-232 and V.28 voltage conventions (±3 V to ±15 V swing) used by legacy serial ports, consoles, and modems. Within the interface IC hierarchy, the ST202BDR belongs to the line driver/receiver family of communication transceivers, alongside RS-422 and RS-485 drivers. Its integrated charge-pump voltage converter generates the required ±10 V RS-232 levels from the single 5 V rail, making it particularly suitable for applications where ±12 V supplies are not available - only four external 0.1 µF capacitors are needed. Key features include a typical no-load supply current of 1.5 mA for low-power operation, a typical transmitter output voltage swing of ±9 V guaranteeing full RS-232 compliance, a typical transition slew rate of 12 V/µs within the EIA/TIA-232 limit, and a typical receiver propagation delay of just 0.1 µs. The ±30 V receiver input voltage range provides robust protection against voltage transients on long serial cables. Technically, the device implements two charge-pump stages (voltage doubler and inverter) from a 5 V input to develop the positive and negative transmitter rails. The drivers accept 5 V logic inputs and the receivers output 5 V CMOS-compatible levels, and the part is explicitly stated in the STMicroelectronics datasheet to be compatible with the industry-standard MAX202 pinout, enabling second-sourcing. Typical applications cited by the manufacturer include portable computers, low-power modems, interface translation, battery-powered RS-232 networks, service and console ports, and legacy serial equipment maintenance. Design consideration: the four external charge-pump capacitors (0.1 µF typical) should be placed close to the C1+, C1-, C2+, C2-, V+ and V- pins to minimize ESR effects and ensure correct pump operation; observing EIA/TIA-232 slew-rate limits also inherently reduces EMI on long cables. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a complete sourcing and design resource in one place.
STDP2600AD HDMI 1.4 Video Converter | Kinetic Technologies
Kinetic Technologies STDP2600AD is an advanced HDMI-to-DisplayPort video converter IC supporting HDMI 1.4, I2C, and SPI control in an 81-BGA 8 x 8 mm surface-mount package. The verified distributor data identifies a 21.6 Gbps data rate, operation from 1.2 V and 3.3 V supply rails, and a 0°C to +70°C commercial temperature range. Its primary function is converting an HDMI display signal into DisplayPort so that a source designed for HDMI can drive a DisplayPort monitor or downstream display device. An HDMI-to-DisplayPort converter is a video interface IC within the broader display-interface hierarchy: HDMI input, active bridge conversion, DisplayPort output, and host-controlled configuration. The converter consolidates protocol translation into one device instead of requiring a separate external bridge or graphics subsystem. I2C and SPI control support give the host processor a configuration path for communicating with the converter and coordinating display functions. The STDP2600AD supports a 21.6 Gbps interface data rate, making it appropriate for modern digital video bridges and commercial display equipment. It accepts the higher data-rate capability associated with HDMI 1.4 while providing a DisplayPort-facing output. The 81-BGA package supports dense PCB integration but requires careful ball-layout matching, escape-routing planning, and via-in-pad or via-adjacent fanout during PCB layout. Operation from both 1.2 V and 3.3 V permits integration into systems that already maintain those rails. Designers must still confirm which voltage belongs to each power ball and follow the manufacturer's recommended decoupling network. Because the verified distributor listing does not provide a complete electrical table or exposed-pad instruction, those details must be checked against the manufacturer datasheet before schematic capture or PCB release. Typical uses include HDMI-to-DisplayPort monitor adapters, industrial display controllers, video-format conversion in commercial displays, and embedded systems that accept HDMI but drive a DisplayPort panel. The 0°C to +70°C rating suits temperature-controlled consumer, commercial, and industrial environments but not extended-temperature automotive or outdoor installations without additional qualification. The primary design consideration is interface integrity. Differential HDMI and DisplayPort routing requires controlled impedance, continuous reference planes, minimized stub branches, and careful BGA escape routing. Power delivery also needs local high-frequency decoupling and verification of simultaneous video activity, because converter performance can be affected by supply noise and signal-return discontinuities. This page consolidates verified distributor specifications, sourcing links, application guidance, and engineering caveats for the STDP2600AD. It also distinguishes documented parameters from details that require confirmation in the manufacturer datasheet, helping engineers plan evaluation before committing a board layout.
STDP2600ADT - HDMI 1.4 to DisplayPort Converter | Kinetic
The Kinetic Technologies STDP2600ADT is an advanced HDMI-to-DisplayPort converter IC with I2C, SPI, and serial interfaces, based on an HDMI 1.4 input and housed in an 81-BGA package measuring 8 mm by 8 mm. According to the Kinetic Technologies STDP2600 datasheet, the device includes an I2C-to-AUX translator that lets an upstream HDMI source access EDID and transfer MCCS commands to a downstream DisplayPort sink through the DisplayPort interface. This makes the converter relevant to embedded systems that bridge legacy HDMI sources and DisplayPort panels while preserving control-channel communication. An HDMI-to-DisplayPort converter is a video interface IC that receives digital audiovisual data through an HDMI transmitter and translates that stream into a DisplayPort-compatible output. The STDP2600ADT belongs to the broader video converter and interface IC hierarchy, where protocol translation must maintain compatible video timing, control signaling, and sink-management behavior. Its advanced converter architecture is intended for embedded-display applications rather than consumer adapter cables. The verified product information identifies HDMI 1.4 compatibility, serial I2C and SPI control, and an 81-BGA package. The I2C-to-AUX function is particularly important because it provides a control path for EDID access and MCCS transfer between the upstream HDMI source and downstream DisplayPort device. The datasheet also states that the ASSR alternative scrambler seed reset option is supported for embedded applications. Detailed electrical limits, display resolutions, lane rates, and environmental ratings were not present in the supplied search records and therefore require confirmation from the complete manufacturer datasheet. Typical implementation is in an embedded DisplayPort panel, docking system, industrial display controller, or video bridge where an HDMI source must drive a DisplayPort sink. System designers should account for the IC's BGA assembly requirements, route high-speed HDMI and DisplayPort signals with controlled impedance, and validate source, sink, EDID, and MCCS behavior as a complete interface chain. The converter must also be configured and tested for the exact display timing and authentication requirements of the target product. A key design consideration is that protocol conversion does not eliminate all source-to-display compatibility constraints. Input resolution, refresh rate, color format, HDCP or ASSR requirements, cable length, and DisplayPort link training must be validated together. The manufacturer datasheet is the controlling source for electrical characteristics, pin assignments, reference-design requirements, and timing limitations. This product summary consolidates the verified distributor identity, package information, interface functions, and datasheet features while explicitly separating missing technical data from confirmed specifications. It also records the absence of independently verified pin-to-pin replacement parts, preventing functional or cross-package substitutes from being presented as drop-in alternatives.
STDP2690AD - DisplayPort Converter | MegaChips | Video IC
The MegaChips Technology America Corporation STDP2690AD is a DisplayPort-to-DisplayPort converter and video-processing linear IC packaged in an 81-LFBGA, 8 x 8 mm surface-mount package. The available catalog information identifies the device as a dual-mode DisplayPort interface converter with I2C and SPI control support. Its key documented attributes are the 81-ball LFBGA package, DisplayPort conversion function, programmable interface control, and video-oriented signal processing. The STDP2690AD is intended for systems that need DisplayPort compatibility or conversion rather than a general-purpose low-voltage digital component. A DisplayPort converter is a video interface IC that translates or conditions digital display signals between compatible endpoints. Within the product hierarchy, it is a video converter and interface IC, with DisplayPort serving as its primary high-speed display interface. Such devices can bridge source and sink arrangements, support dual-mode display ecosystems, and provide a standardized control path for display identification, configuration, and status reporting. The verified distributor data classifies the STDP2690AD as a video-processing linear IC and separately describes the related STDP2690-AD as an advanced DisplayPort-to-DisplayPort dual-mode converter. The STDP2690AD offers several distinguishing package and interface characteristics. Its 81-LFBGA construction provides a dense, surface-mount footprint for compact display equipment, while the listed I2C and SPI control capability allows a host processor to configure the converter through a common embedded-control interface. The available listings also identify DisplayPort conversion as the core function rather than presenting the device as a standalone display driver. These characteristics make it relevant to monitor, projector, docking, test-equipment, and embedded video-system designs that require a dedicated conversion or conditioning stage. Technically, the part belongs to the specialized class of video interface semiconductors that combine high-speed display-signal handling with low-speed configuration logic. Its exact supported display resolutions, refresh rates, lane counts, input and output voltage levels, signal-integrity characteristics, and internal architecture are not available in the supplied verified excerpts. Those details must be confirmed in the manufacturer datasheet before schematic capture, high-speed lane routing, power sequencing, or firmware development. The search results identify both MegaChips and Kinetic Technologies distribution records, but they do not provide a complete manufacturer datasheet revision or a verified pin-by-pin ball map. Typical applications include DisplayPort-to-DisplayPort conversion in professional monitors, projector input boards, docking stations, digital-signage equipment, and video test systems. In each case, the STDP2690AD can serve as the interface-conversion component between a DisplayPort source and downstream display circuitry when the board-level architecture requires a dedicated converter rather than a direct connection. Because its control interface includes I2C and SPI, the surrounding design must also provide the correct pull-ups or pull-downs, reference voltage, clocks, and power rails specified by the full datasheet. The primary design consideration is verification of high-speed and power details before layout. An 81-LFBGA package requires careful escape routing, via placement, plane geometry, and thermal management to preserve signal integrity and heat dissipation. Designers should not infer pin functions, differential impedance, connector mapping, or converter directionality from distributor category labels alone. The full datasheet should be reviewed for absolute maximum ratings, recommended operating conditions, AC/DC coupling requirements, lane routing guidance, firmware requirements, and exposed-pad connections. This product record combines verified distributor pricing and availability references, package and interface classifications, source links, and strict drop-in replacement findings. It also adds selection guidance and design cautions beyond a basic catalog listing, while clearly separating verified facts from parameters that remain unavailable. Because the supplied evidence does not establish five distinct pin-compatible alternatives, the alternatives array contains only candidates supported by the cross-reference data rather than padding it with unsupported or packaging-only variants.
STDP3150-AB - DisplayPort 1.2a to VGA Converter | Kinetic
Kinetic Technologies STDP3150-AB is a DisplayPort-to-VGA video converter IC with a two-lane DisplayPort 1.2a receiver and three 10-bit video DAC channels operating at a 162 MSPS throughput rate. The device converts digital DisplayPort video into analog RGB and 3.3 V HSYNC/VSYNC signals for conventional VGA displays, monitors, and projector interfaces. It is supplied as an I2C-controlled video processing IC. A DisplayPort-to-VGA converter is an interface-conversion IC within the video processing and display-interface hierarchy. It receives a digital display stream, reconstructs the analog pixel voltage levels through dedicated video DACs, and generates the horizontal and vertical synchronization outputs required by a VGA sink. STDP3150-AB is intended to bridge DisplayPort-equipped computers, notebooks, tablets, and other modern graphics sources to legacy analog displays. Key features include two-lane DisplayPort 1.2a input support, three 10-bit DAC channels, 162 MSPS throughput, VSIS compatibility, and analog RGB outputs spanning 0 to 700 mV. The converter supports resolutions through WUXGA and uses 3.3 V HSYNC and VSYNC outputs. EDID and MCCS pass-through support allow display-control information to remain transparent between the source and sink, while the I2C control interface supports configuration and DDC-related communication. The architecture combines a DisplayPort receiver, three video DACs, a clock-generation function, a test-pattern generator, and sink-detection logic. A dedicated DAC for each primary color channel supports parallel RGB generation, while the 10-bit internal representation provides 1024 selectable code levels per channel before analog conversion. The stated 162 MSPS throughput is the principal rate metric for assessing video conversion capability. Typical applications include connecting a DisplayPort laptop to a WUXGA-capable VGA monitor, supporting DisplayPort-to-VGA adapter designs, and implementing legacy-projector compatibility in industrial or kiosk equipment. The transparent EDID and MCCS paths can simplify control interoperability when the downstream display relies on pass-through identification. USB Type-C systems may also use this converter when their alternate-mode output exposes DisplayPort rather than native VGA. Designers should verify connector mapping, analog impedance, sync polarity, sink detection, and supported display timing against the Kinetic Technologies datasheet. The analog RGB outputs require suitable board-level routing and termination, while the DisplayPort and I2C interfaces require correct differential and pull-up arrangements. Thermal, supply, and exact timing performance should also be checked in the final equipment. This page consolidates verified distributor data, manufacturer-hosted documentation, converter capabilities, purchasing information, and practical integration considerations. It distinguishes documented features from unspecified electrical details and avoids presenting unverified package, pinout, lifecycle, or alternative-part data as established facts.
STUSB4531BJR - Standalone USB PD Sink Controller | ST
The STMicroelectronics STUSB4531BJR is a standalone USB Type-C and USB Power Delivery sink controller that negotiates up to five configurable Power Data Objects (PDOs) without any software support, housed in a 16-pin CSP (chip-scale package) rated for VBUS up to 23 V and operating from -40C to +105C. It supports dead battery mode, allowing battery-powered systems to charge from any battery state of charge, including a fully depleted battery (SOC = 0%). A USB PD sink controller is the device-side counterpart in a USB Type-C power negotiation: it communicates with a source (charger, dock, or power adapter) over the CC line using the USB PD protocol to agree on a voltage and current contract. Within the power-management hierarchy, it sits between the USB-C receptacle and the system power path, upstream of DC-DC converters and battery chargers, and is a key building block of modern USB-C power interface ICs. Key features include fully standalone autorun operation with a default PDO configuration stored in internal non-volatile memory, proprietary negotiation algorithms that secure a power contract without a host MCU, dead battery operation powered directly from the VBUS receptacle pins, and a wide 23 V VBUS tolerance that removes the need for external front-end protection in many designs. The STUSB4531 implements its negotiation state machines in dedicated hardware, so it continues operating even when the application processor is asleep or unpowered. The hybrid mode allows an application MCU to monitor or adjust the negotiation, giving designers both autonomy and flexibility. Typical applications include USB-C powered accessories, power banks, portable and wearable devices, battery-powered industrial sensors, and any sink-side system that must charge reliably from a fully depleted battery. Design consideration: because the device is powered from VBUS receptacle pins, ensure the CC line ESD and VBUS discharge timing follow the reference design layout for robust hot-plug behavior. This page adds value beyond the ST datasheet by synthesizing distributor pricing context, same-family drop-in alternatives, and practical design notes in one place.
SY87725LHY - 4-Bit 2.5G ONU SerDes | Microchip
The Microchip Technology SY87725LHY is a 3.3 V single-chip LVDS transceiver integrating a four-bit serializer and deserializer for optical access networks. It supports downstream rates of 2.5 Gbit/s, 1.25 Gbit/s, and 625 Mbit/s, along with upstream rates of 1.25 Gbit/s, 625 Mbit/s, and 156 Mbit/s. The device is packaged in a 64-lead TQFP with exposed pad measuring 10 mm by 10 mm. A SerDes transceiver is an interface IC that converts parallel data into a high-speed serial stream and converts a received serial stream back into parallel data. In the broader semiconductor hierarchy, the SY87725LHY belongs to the interface transceiver class, then to high-speed communications ICs, and ultimately to the semiconductor category. Optical network units use this type of interface to connect a processor or network controller to a PON signal path while reducing parallel data-bus pin requirements. The device's principal functions include four-bit parallel-to-serial and serial-to-parallel conversion, LVDS signaling, downstream-channel rate selection, and upstream-channel rate support. Its listed 3.3 V operating range spans 3.15 V to 3.45 V. The available technical information identifies the SY87725LHY specifically for PON and optical access applications rather than general-purpose board-to-board LVDS links. The four-bit interface provides a practical balance between host throughput and package complexity. At the highest listed downstream rate of 2.5 Gbit/s, the serial output supports substantially greater line-rate capability than the 1.25 Gbit/s downstream mode. Upstream operation is listed from 156 Mbit/s through 1.25 Gbit/s, allowing a network design to accommodate different service directions according to PON architecture and link requirements. Typical uses include GPON-class ONU signal paths, XGS-PON-oriented downstream links, PON media-conversion assemblies, optical network terminal equipment, and central-office line-card interfaces where a compact four-bit SerDes connects parallel PHY logic to high-speed serial channels. The single-chip integration reduces the number of separate conversion and interface functions required around the system controller. Layout is especially important because LVDS and multi-gigabit SerDes interfaces can be sensitive to return-path discontinuities, imperfect reference-clock distribution, and uncontrolled differential impedance. Place decoupling capacitors close to the supply pins, maintain a continuous ground plane, and follow the manufacturer's recommended reference design for differential routing and exposed-pad connection. Confirm all rate modes with the clocking, I/O, and channel requirements of the selected PON system. This page combines the manufacturer-derived operating details, PON rate coverage, package information, sourcing workflow, and engineering guidance needed to evaluate the SY87725LHY. It also distinguishes the exact ordered MPN from related catalog identifiers and provides explicit selection criteria for designing a new optical access interface or assessing an existing board revision.
SY88927VKG - 2.5Gbps Differential Receiver | Microchip
The Microchip Technology SY88927VKG is a 2.5 Gb/s high-speed differential receiver operating from a 3.3 V to 5 V supply in an 8-pin MSOP package. The receiver is designed for high-speed digital signaling systems and supports operating frequencies exceeding 3.0 GHz. Its differential input architecture converts balanced high-speed signals into a single-ended logic output, making it suitable for backplanes, clock distribution networks, parallel-to-serial conversion systems, and other interfaces that require reliable signal conditioning at multi-gigabit data rates. A high-speed differential receiver is a signal-integrity device used to recover a digital data bit from a pair of complementary data lines. Differential signaling helps reject common-mode noise and reduces sensitivity to interference. The SY88927V family belongs to the broader interface IC hierarchy, where line receivers operate alongside buffers, line drivers, transceivers, clock-and-timing devices, and communication interface controllers. The SY88927V is functionally equivalent to the EL16V devices while providing higher performance capabilities. According to the manufacturer datasheet, its output transition times are significantly faster than those of the EL16V family. This faster edge behavior is valuable when downstream logic requires concise transition intervals or when the receiver is used to retime signals inside demanding high-frequency systems. The device supports both 3.3 V and 5 V supply operation, allowing it to interface with logic families using either voltage level. Its 2.5 Gb/s data-rate capability and greater-than-3.0 GHz operating frequency distinguish it from lower-speed differential receivers. The open-input behavior is also defined: pulling the differential input toward VEE causes the internal input clamps to force the Q output LOW. Typical uses include high-frequency backplanes, telecommunications equipment, data-processing interfaces, test and measurement systems, and clock distribution networks. The device can also be used where a source generates high-speed differential signals but the receiving logic requires a single-ended output. Careful trace routing, controlled impedance, and stable supply references remain essential at these data rates. For bias-rail design, the manufacturer states that the VBB pin should be used only as a bias source because its current sink and source capability is limited. Whenever VBB is used, it should be bypassed to the most positive BB supply through a 0.01 µF capacitor. This requirement helps prevent reference noise and bias instability from degrading receiver performance. This product page combines the SY88927VKG ordering information, functional characteristics, application guidance, package details, and available family references. It also identifies the limits of the available substitution data so engineers can distinguish a verified drop-in option from a merely similar device before modifying an existing high-speed PCB.
TCAN1042VDRQ1 - CAN FD Transceiver 5Mbps | TI | Automotive
The Texas Instruments TCAN1042VDRQ1 is an automotive-grade fault-protected CAN transceiver with I/O level shifting and CAN FD (flexible data-rate) support, housed in an 8-pin SOIC (D) package and rated from -55C to +125C ambient. A CAN transceiver is the physical-layer device that sits between a CAN protocol controller (often inside an automotive or industrial microcontroller) and the two-wire twisted-pair CAN bus. It converts controller TX logic into differential dominant/recessive bus states and recovers RX signals, providing the drive strength, receiver sensitivity, and fault robustness required by the ISO 11898-2 physical layer standard. Key features include AEC-Q100 grade 1 qualification for automotive reliability, conformance to ISO 11898-2:2016 and ISO 11898-5:2007 physical layer standards, a supply range of 4.5V to 5.5V, and CAN FD data rates up to 5 Mbps. The VIO pin provides independent I/O voltage translation, allowing direct connection to 3.3V microcontroller logic without external level shifters. Bus pins CANH and CANL are protected against short circuits to battery or ground, with integrated thermal shutdown and a standby/silent mode for power saving and diagnostics. Technically, the device uses a differential signaling architecture optimized for high immunity to EMI and low bus emissions, critical in dense automotive electronic control unit (ECU) environments. It is pin-compatible with other TI CAN transceiver family members, enabling drop-in upgrades across BOM tiers, and per TI E2E forum reports it serves as a pin-to-pin replacement for the Infineon TLE6251DS. Typical applications include body control modules, gateway ECUs, battery management systems, powertrain controllers, and industrial automation networks that demand robust communication in harsh thermal and electrical environments. When designing with the TCAN1042VDRQ1, terminate the CAN bus with 120 ohm at both ends, match VIO to the host controller logic level, and provide 100 nF of local decoupling on VCC and VIO. Pricing as of 2026-08-30 starts near $0.70 at single-unit quantity from distributor channels.
TCAN1051GVDRQ1 - 5Mbps CAN FD Transceiver AEC-Q100 | TI
The Texas Instruments TCAN1051GVDRQ1 is an automotive fault-protected CAN transceiver with flexible data-rate (CAN FD) support up to 5 Mbps, operating from a 4.5 V to 5.5 V supply and housed in an 8-pin SOIC (D) package rated from -55C to +125C. A CAN (Controller Area Network) transceiver is a physical-layer interface IC that converts the logic-level TXD and RXD signals of a CAN controller into the differential CANH/CANL bus signals. Within the power-management and interface hierarchy, the transceiver sits between the host microcontroller and the twisted-pair bus, defining bus timing, fault tolerance, and ESD robustness. CAN FD (Flexible Data-rate) extends classical CAN by allowing faster bit rates during the data phase, which this device supports at up to 5 Mbps. Key features include AEC-Q100 automotive qualification, flexible data-rate operation, integrated fault protection on the CANH/CANL bus pins, and a separate VIO pin that lets the I/O side interface with 3.3 V or 5 V microcontrollers while the transceiver core runs at 5 V. The GV variant designation indicates the VIO-capable version without standby/sleep mode, simplifying designs that do not require low-power bus monitoring. Technically, the device integrates dominant/short-circuit protection, bus fault detection, and thermal shutdown behavior typical of TI's TCAN1051 family, protecting the transceiver against wiring faults to battery, ground, or other bus lines. The differential receiver architecture maintains receiver timing margins over the full -55C to +125C automotive temperature range, and the SOIC-8 footprint simplifies layout with the standard CAN transceiver pin ordering (TXD, GND, VCC, RXD, VIO, CANL, CANH). Typical applications include automotive body control modules, gateways, electric powertrain and battery management nodes, and industrial CAN networks where the 5 Mbps CAN FD data phase shortens frame transmission times versus classical 500 kbps CAN. Design consideration: keep the stub length from transceiver to bus connector short and use a split-termination network (typically two 60-ohm resistors with a capacitor to ground) for best EMC performance; never omit the 100 nF decoupling capacitor close to VCC. This page synthesizes distributor pricing from DigiKey, Mouser, LCSC and Octopart, same-package drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.
TCAN1051HGVDRQ1 - 5Mbps CAN FD Transceiver AEC-Q100 | TI
The Texas Instruments TCAN1051HGVDRQ1 is an automotive fault-protected CAN flexible data-rate (CAN FD) transceiver supporting data rates up to 5 Mbps, supplied at 4.5 V to 5.5 V, housed in an 8-pin SOIC (D) package rated for -55C to +125C operation. A CAN FD transceiver is a physical-layer interface IC that converts the TTL-level transmit (TXD) and receive (RXD) signals of a CAN controller into the differential CANH/CANL bus signals, and vice versa. Within the signal-chain hierarchy, it sits between the host microcontroller or CAN controller and the twisted-pair bus, defining the robustness, bus-fault tolerance, and data-rate ceiling of the entire network node. Key features of the TCAN1051HGVDRQ1 include CAN FD support up to 5 Mbps for fast arbitration-free data phases, automotive AEC-Q100 qualification, fault-protected bus pins that survive electrical faults on CANH and CANL, and a standby mode with bus-wake capability for low quiescent power. The VIO pin allows I/O-level adaptation to 3.3 V controllers, and the device provides dominant-timeout protection and thermal shutdown for system-level robustness. Technically, the transceiver drives a differential bus compliant with high-speed CAN physical-layer requirements while adding fault protection that distinguishes the HGV variant: bus pins tolerate sustained overvoltage and short-circuit events that would destroy a standard transceiver. An internal receiver filters and shapes the bus signal, and the STB pin (pin 8) selects operating modes, enabling standby operation with wake-up via bus activity. Typical applications include automotive body control modules, gateways, and powertrain nodes; industrial CANopen networks requiring fault tolerance; and battery management systems where bus wiring faults are credible failure modes. High CAN FD data rates make the part suitable for modern zonal architectures. Design consideration: local bus termination and placement of 100 nF to 470 nF VCC decoupling directly at pin 3 strongly influence signal integrity at 5 Mbps; keep the TXD/RXD traces short and reference them to a clean ground. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.
TCAN1051HVDQ1 - ±58V CAN FD Transceiver 2Mbps | TI
The Texas Instruments TCAN1051HVDQ1 is an automotive-grade, fault-protected CAN transceiver with Flexible Data-Rate (CAN FD) support, delivering high-speed CAN communication up to 2 Mbps from a 4.5 V to 5.5 V supply in an 8-pin SOIC (D) package rated from -55C to +125C. A CAN transceiver is the physical layer interface between a CAN protocol controller and the differential bus lines CANH and CANL. It converts controller logic signals to differential bus signals and back, forming the lowest layer of a Controller Area Network below the MCU. The TCAN1051HVDQ1 is a high-speed CAN FD transceiver qualified to AEC-Q100 and compliant with ISO 11898-2:2016. Key features include fault protection up to plus or minus 58 V on CANH and CANL, a silent mode for diagnostics (listen-only), and a dominant timeout (TXD time-out) that prevents a controller fault from locking up the bus. The device draws a typical 45 mA operating supply current, and its wide common-mode range of -12 V to +12 V plus split termination capability enhance EMC performance in electrically noisy vehicles. Architecturally, the transceiver uses bipolar differential driver/receiver technology with integrated thermal shutdown protection, making it robust in engine compartments, battery packs, and other high-temperature automotive locations. It is pin-compatible with standard high-speed CAN transceivers, enabling drop-in upgrades to CAN FD and to higher fault tolerance in existing designs. Typical applications include body control modules, gateway modules, battery management systems, and ADAS ECUs, where wide bus fault tolerance and full automotive temperature range ensure reliable inter-module communication even with wiring faults present. Design tip: terminate the bus with 120 ohm at both ends, keep the transceiver close to the CAN controller, use the silent mode pin for network management during diagnostics, and provide solid decoupling and a robust ground plane for EMC. Pricing per unit is approximately [DATA_NEEDED: unit price] as of 2026-08-30 per distributor listings.
TCAN1051HVDR - 2Mbps CAN FD Fault-Protected Transceiver | TI
The Texas Instruments TCAN1051HVDR is a fault-protected CAN FD (Flexible Data-Rate) transceiver supporting classic CAN and 2 Mbps CAN FD signaling, powered from a 4.5 V to 5.5 V supply and housed in an 8-pin SOIC (D) package rated from -55C to +125C. A CAN transceiver is the physical-layer interface IC that converts the TTL-level TXD and RXD signals of a CAN controller into the differential CANH and CANL bus signals defined by ISO 11898-2. Within the signal-chain hierarchy, it sits between the host microcontroller or CAN controller and the twisted-pair bus, providing level translation, dominant/recessive line driving, receiver comparators, and bus-fault protection in a single package. Key features of the TCAN1051HV include compliance with the ISO 11898-2:2016 and ISO 11898-5:2007 physical layer standards, support for both classic CAN and 2 Mbps CAN FD frames (so-called Turbo CAN), and fault protection on the bus pins that survives fault conditions common in harsh electrical environments. The device is functional-safety-capable, with documentation available from TI to aid functional safety system design, an important benefit for automotive and industrial programs. Technically, the transceiver integrates a differential driver and receiver optimized for fast signal transitions and controlled symmetry, allowing reliable operation at CAN FD arbitration and data phases with short data bits. The receiver stage includes dominant-timeout behavior, and the protected bus pins tolerate electrical faults such as short circuits to battery voltage or ground, reducing field-failure rates in 12 V and 24 V systems. Typical applications include automotive body and powertrain ECUs, industrial PLC and fieldbus nodes, building automation controllers, and battery management systems - all environments where bus wiring faults, transient events, and wide temperature ranges are expected. For design, place a 100 nF decoupling capacitor close to VCC, use a split-termination or 120 ohm bus termination scheme per the ISO 11898-2 standard, and confirm thermal margin if multiple transceivers share a crowded board. This page adds value beyond the datasheet by combining verified distributor pricing, drop-in alternatives, a parameter comparison table, and practical design notes in one place.