Interface ICs
ژێرپۆلەکان
بەرهەمەکان (560+)
CS8421-CNZ - 32-Bit 192kHz Stereo SRC | Cirrus Logic
The Cirrus Logic CS8421-CNZ is a 32-bit, 192 kHz asynchronous stereo sample-rate converter in a 20-QFN package measuring 5 mm by 5 mm. It converts digital audio streams between different sampling rates using two channels, supports input and output word lengths of 16, 20, 24, or 32 bits, and can operate with completely asynchronous input and output clocks. The converter also supports external data-clock operation or autonomous operation using an integrated oscillator. A sample-rate converter is an interface IC that translates digital audio data from one clock domain to another without requiring the source and destination equipment to share a common sample clock. It belongs to the digital-audio IC hierarchy alongside audio codecs and digital audio interfaces. This capability is useful when equipment must accept audio from a clock domain that differs from the internal processing rate, such as a computer, broadcast, studio, or networked audio system. Principal performance features include a 175 dB dynamic range, -140 dB THD+N, operation without programming, and no requirement for an external master clock. Sampling rates can reach 211 kHz, with input-to-output sample-rate ratios spanning 1:8. The master-clock section supports 128 times Fs, 256 times Fs, and bypass operation, while the time-division multiplexing interface provides a practical connection to digital audio processors and transport devices. The CS8421 uses a monolithic CMOS implementation to combine asynchronous rate conversion, clocking support, and multichannel digital-audio routing in one device. Its 32-bit datapath accommodates high-resolution PCM audio, while the integrated oscillator offers a practical fallback when no external master clock is available. The 20-QFN surface-mount package supports compact audio conversion and clock-isolation designs, although careful decoupling and signal-routing practices remain necessary for high-performance audio boards. Typical uses include asynchronous audio bridges, digital mixing consoles, studio preamplifiers, broadcast equipment, hi-fi DAC boards, computer-audio interfaces, and multimedia systems that must reconcile unrelated sample-rate domains. The device is particularly valuable when converting high-resolution PCM streams to a rate accepted by an ADC, DAC, DSP, or digital transport while preserving low distortion and high dynamic range. For implementation, follow the pin-description table and reference configuration in the manufacturer datasheet when assigning data, clock, control, supply, and ground connections. Place input and output decoupling capacitors close to their associated pins, route high-speed digital signals over continuous reference planes, and isolate asynchronous clocks from sensitive analog sections to minimize data-dependent jitter and crosstalk. This product page combines the principal CS8421-CNZ operating characteristics with application guidance, lifecycle information, pinout-status disclosure, and a strict drop-in-replacement assessment. It also distinguishes verified engineering constraints from unavailable procurement details so engineers can evaluate the converter for a new design or an existing production board.
CS8421-DZZ 32-Bit 192 kHz Audio SRC | Cirrus Logic
The Cirrus Logic CS8421-DZZ is a 32-bit, 192 kHz asynchronous stereo audio sample-rate converter packaged in a 20-pin TSSOP. It is designed for transparent conversion between asynchronous audio clock domains, supporting two-channel operation while maintaining 175 dB dynamic range and -140 dB THD+N according to the Cirrus Logic product page. The device operates from a 2.38 V to 2.62 V core supply and is specified over -40°C to +85°C. An asynchronous sample-rate converter is an audio interface device that accepts an input signal associated with one clock frequency and resamples it to a different output clock. It sits within the audio signal-chain hierarchy as a sample-rate converter, clock-domain interface, audio interface IC, and ultimately an analog-and-mixed-signal semiconductor. This makes it useful where a source device, digital audio processor, DAC, or network playback engine does not share a common master clock. Key characteristics of the CS8421-DZZ include 32-bit processing, a maximum sample rate of 192 kHz, stereo two-channel capability, and an asynchronous conversion architecture. Its stated dynamic range of 175 dB and THD+N of -140 dB make it appropriate for professional studio equipment, high-end consumer audio, digital mixers, broadcast infrastructure, and clock-domain isolation between digital audio sources. The 20-lead TSSOP package also permits reuse of TSSOP-20 board layouts where the surrounding circuitry satisfies the interface and grounding requirements. The CS8421-DZZ is identified by Cirrus Logic as discontinued. The family is also offered in a 20-pin QFN package, but that package option is not pin-compatible with the leaded CS8421-DZZ and therefore is not a drop-in substitution. Existing designs should check supply availability and consider a functionally similar asynchronous converter only after verifying digital interface timing, master-clock requirements, control logic, voltage levels, and package dimensions. When laying out a board, route the audio data and clock signals away from switching-node and high-current supply traces, provide solid ground-plane return paths, and decouple the 2.5 V core rail close to the device. Differential data signals should be length-matched within the limits stated in the manufacturer datasheet, and unused interface pins should be configured according to the device pin-description table rather than left floating by assumption. This page consolidates lifecycle information, verified package and operating details, application guidance, and drop-in replacement analysis. It also documents the key engineering constraints engineers must check before reusing a CS8421-DZZ design or selecting a replacement: exact pinout, master-clock topology, audio word length, sample-rate range, control-register behavior, power sequencing, and board-level isolation.
CS8952-CQ - 10/100 Ethernet PHY | Cirrus Logic | 100-TQFP
The Cirrus Logic CS8952-CQ is a CrystalLAN 10BASE-T and 100BASE-X Ethernet physical-layer transceiver with a 5 V supply, 10 Mb/s and 100 Mb/s operation, and a 100-pin TQFP package measuring 14 mm by 14 mm. It provides a Media Independent Interface for connection to a network Media Access Controller and supports 100BASE-TX copper, 100BASE-FX fiber, and 10BASE-T links. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts parallel controller-facing signals into physical network signals and receives incoming physical-layer signals for delivery to the MAC. The CS8952-CQ belongs to the interface-IC hierarchy, where a PHY sits beneath the Ethernet MAC and above the physical copper or fiber medium. Its MII interface supports both 10 Mb/s and 100 Mb/s designs, while its pseudo-ECL interface is intended for external 100BASE-FX optical modules. The adaptive receive equalizer is optimized for immunity to noise and near-end crosstalk, and the manufacturer describes receiver operation over cable lengths exceeding 160 m under suitable conditions. The device also emphasizes low transmit jitter, with a published feature value below 400 ps. These characteristics make the PHY applicable to network interface cards, Ethernet switches, repeaters, and embedded equipment requiring a parallel MAC interface rather than a modern serial PHY interface. Internally, the CS8952-CQ is a CMOS physical-layer IC combining 10BASE-T and 100BASE-X functions. Its operating modes can be tailored for low-latency 100BASE-TX repeaters, switches, and MII-based network interface cards. Control and status registers provide access to operating characteristics, while the MII handles parallel data transfer and interconnects with compatible 10 Mb/s or 100 Mb/s Media Access Controllers. Typical applications include legacy Ethernet network interface cards, 100BASE-TX switching equipment, 100BASE-FX optical links using external fiber modules, industrial control networking, and legacy embedded Ethernet equipment. For copper designs, magnetic-interface components and a correctly terminated network transformer are required. Fiber implementations also require an external optical transceiver compatible with the CS8952-CQ pseudo-ECL interface. When laying out a CS8952-CQ board, treat the MII, clock, power, and analog network paths as separate high-speed and potentially noisy domains. Place input and output decoupling capacitors close to the device, route the MII clock carefully, and follow the reference layout and component-selection guidance in the manufacturer datasheet. Maintain short return paths and appropriate isolation between the digital controller interface and copper or fiber media interfaces. This product page combines the CS8952-CQ ordering information, package details, electrical coverage, drop-in family options, comparison data, and practical Ethernet interface design guidance. It is intended to help engineers identify whether the legacy MII-based CrystalLAN transceiver remains suitable for a specific 10 Mb/s or 100 Mb/s network design before placing the final order.
CY7C64225-28PVXC - USB-UART Bridge Controller | Infineon
The Infineon CY7C64225-28PVXC (originally Cypress Semiconductor, EZ-USB E3 family) is a single-channel USB 2.0 full-speed to UART bridge controller with RS-485 support and hardware flow control, operating from 3.0 V to 5.25 V and housed in a 28-pin SSOP package supplied in tray packing. A USB-to-UART bridge controller is an interface IC that converts data between a USB host (typically a PC) and a device with a UART serial port, enabling legacy serial designs to connect to modern USB hosts without firmware changes on the serial side. Within the system hierarchy, it belongs to interface bridges under USB interface ICs, a category essential for industrial, instrumentation, and point-of-sale equipment. Key features include full-speed USB 2.0 operation compliant with the USB specification, USB-IF certification with TID 40001425, three USB endpoints (1 Interrupt IN, 1 Bulk OUT, 1 Bulk IN), an integrated USB transceiver with a 1.5 kOhm pull-up resistor on the D+ line, and support for both bus-powered and self-powered configurations. The integrated flash memory allows vendor-specific descriptors and configuration to be customized. Architecturally, the device contains an on-chip USB engine, a 64-byte FIFO buffer for UART data flow smoothing, and a UART interface supporting RS-485 signaling and hardware flow control (RTS/CTS), which reduces CPU overhead and prevents data loss at high baud rates. The 3.3 V internal operation with wide 3.0 V to 5.25 V supply tolerance simplifies integration in both 3.3 V and 5 V systems. Typical applications include legacy RS-232/RS-485 equipment migration to USB, point-of-sale terminals, industrial instrumentation panels, and set-top box debug ports, where a simple driver-based USB serial link is required. Design consideration: for bus-powered designs, ensure the suspend current budget accounts for the bridge controller's suspend mode, and keep the 1.5 kOhm D+ pull-up resistor unconnected externally to avoid double-pull-up errors. This page synthesizes distributor pricing (Mouser, Octopart, Newark, DigiKey), stock status, packaging details, and drop-in variant analysis not consolidated in the manufacturer datasheet.
CY7C65634-28LTXCT - 2-Port USB 2.0 Hub | Infineon
Infineon Technologies CY7C65634-28LTXCT is a two-port, single-TT USB 2.0 hub controller with configurable GPIO and EEPROM support, supplied in a 28-pin QFN package with an exposed pad on a 5 mm by 5 mm footprint. The controller supports low-speed, full-speed, and high-speed USB operation and operates from 3.3 V or 5 V supply rails. A USB hub controller is an interface integrated circuit that manages traffic between a USB host and one or more downstream USB devices. It belongs to the USB interface-controller family within the broader semiconductor and embedded-interface hierarchy. A single-TT hub topology separates low- and full-speed traffic from high-speed traffic, helping simplify downstream routing and reduce the performance burden placed on shared bus segments when devices of different speeds are connected. The CY7C65634-28LTXCT provides two downstream hub ports and allows implementation choices through GPIO and EEPROM configuration. These features make the device useful where a compact board needs managed USB connectivity rather than a simple passive splitter. The exposed-pad package supports heat transfer from the controller to the PCB copper, while its compact 5 mm by 5 mm dimensions support space-conscious USB peripheral and embedded-product layouts. The part is identified as C-grade and is associated with a commercial operating-temperature class. Infineon’s ordering information describes the CT ordering suffix as a tape-and-reel configuration. The exact pin assignments, clock requirements, transceiver characteristics, current limits, and configuration registers should be taken from the manufacturer datasheet before schematic capture or PCB layout is released. Typical applications include compact USB hubs, personal-computer peripherals, embedded USB expansion, industrial data-acquisition equipment, USB test systems, and dual-device connectivity products. The two-port arrangement is especially useful when a system must expose two USB connectors while retaining a controlled host-to-device relationship and configurable interface behavior. PCB implementation should preserve the exposed-pad grounding and thermal-via pattern specified by the manufacturer. USB differential routing also requires short, matched traces, controlled impedance, and careful separation from noisy power-conversion paths. Because this controller coordinates high-speed signaling, layout errors can affect enumeration, signal integrity, or interoperability even when the schematic is electrically correct. This page consolidates the manufacturer ordering information, package characteristics, sourcing details, application guidance, and engineering considerations into a design-focused component profile. It also distinguishes exact ordering variants from functional drop-in alternatives, helping engineers make sourcing and PCB-compatibility decisions before committing a USB hub design to production.
DAC8742HPBSR - HART and PROFIBUS PA Modem | Texas Instruments
Texas Instruments DAC8742HPBSR is a HART, FOUNDATION Fieldbus, and PROFIBUS PA-compatible modem with UART/SPI support, packaged in a 32-pin TQFP (5 mm × 5 mm). It integrates the circuitry required for half-duplex HART physical-layer operation in master or slave configurations, while the manufacturer describes it as a low-power industrial process-control and automation interface. The verified product listing identifies the device as a specialized HART modem interface rather than a general-purpose converter. A HART modem is an industrial communication interface that overlays analog process-control signals with digital data. The DAC8742H family combines modem functionality with an interface suitable for sensors, actuators, transmitters, and fieldbus equipment. Its protocol support links it to FOUNDATION Fieldbus and PROFIBUS PA systems, where robust physical-layer signaling and low-power operation are important for factory automation, process control, and connected industrial instruments. The primary verified features are compatibility with HART, FOUNDATION Fieldbus, and PROFIBUS PA; support for both UART and SPI host interfaces; operation as a half-duplex HART modem in master or slave mode; and integration of the required circuitry with minimal external filtering components. The low-power architecture targets industrial equipment where a dedicated modem without excessive board area or power consumption is valuable. Exact supply ratings, current limits, data rates, and temperature limits are not present in the supplied excerpts and therefore are not asserted here. For a HART master, the device works with the transmitter and receiver circuitry associated with a multidrop fieldbus. For a slave, it supports a field device that communicates over the same physical network. UART/SPI host connectivity allows a microcontroller, industrial communications controller, or programmable logic controller to configure and supervise the modem. These roles make the DAC8742HPBSR relevant to transmitters, pressure and temperature instruments, valve positioning systems, industrial I/O modules, and process-control gateways. The principal design consideration is analog and communication robustness. The 32-pin TQFP requires a controlled high-density PCB layout, adequate ground-plane continuity, and careful treatment of modem and interface routing. Power-supply filtering and external component selection should follow the manufacturer datasheet rather than generic guidance. Because the supplied data does not expose the complete electrical tables or pin mapping, engineers should confirm pinout, bypass requirements, isolation requirements, and timing limits before layout release. This product page combines the verified manufacturer identity, distributor availability, package information, protocol coverage, and interface capabilities with structured engineering guidance. It also distinguishes documented facts from parameters that still require confirmation from the complete Texas Instruments DAC8742H datasheet, helping procurement and design teams assess fit before committing to a PCB or production release.
DG202CJ+ - Quad SPST 200Ω Analog Switch | Analog Devices
Analog Devices DG202CJ+ is a quad SPST CMOS analog switch with four normally open channels, 200 ohm on-resistance, inverted control inputs, and a 16-pin PDIP package. The device operates from ±4.5 V to ±18 V, supports bipolar signal switching, and is designed for analog signal routing in test, measurement, industrial, and communication equipment. An analog switch is an integrated semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw, or SPST, switch provides one signal path that is normally open until its control input commands closure. The DG202CJ+ belongs to the analog-switch hierarchy, where CMOS construction supports low-power operation, bidirectional signal passage, and operation across both positive and negative supply rails. The four independently controlled channels provide 4:1 routing capability in a single package. Each channel has a specified 200 ohm on-resistance, while the normally open configuration prevents signal flow while deasserted. Break-before-make behavior helps avoid connecting two driven sources simultaneously during transitions. The DG202 family uses the Intersil 44 V CMOS process, and its latch-proof construction helps prevent unwanted operation when supplies are disconnected while signals remain present. The DG202CJ+ supports dual supplies from ±4.5 V to ±18 V. Published family information identifies maximum turn-on time of 600 ns and maximum turn-off time of 450 ns. The family can block signals up to 30 V peak-to-peak in the OFF state, making it useful where signals can exceed the nominal supply range. The DIP-16 package supports conventional through-hole assembly and straightforward laboratory prototyping. Typical uses include multiplexed data acquisition, sensor selection, test-point routing, signal isolation, sample-and-hold subsystems, and communication interface switching. The four independent channels are particularly useful when several analog sources must share a downstream amplifier, converter, or measurement instrument without constructing separate discrete switch networks. Designers should verify signal amplitude, supply sequencing, control-logic levels, off-state leakage, and on-resistance error against the manufacturer datasheet. Logic-high and logic-low levels must remain compatible with the selected supply condition, and unused control or signal pins should be handled exactly as specified in the datasheet. This page combines verified manufacturer and distributor information with a focused engineering comparison, drop-in sourcing assessment, and practical design guidance. It distinguishes true package-compatible replacements from related DG202 package variants that cannot be substituted without changing the PCB footprint.
DG405DJ+ - 45Ω Dual High-Speed Analog Switch | Analog Devices
Analog Devices DG405DJ+ is a dual, high-speed CMOS analog switch with two independently controlled 2:1 channels, a 45 Ω on-resistance rating, and a 16-pin PDIP package. The device supports normally open switch operation and is designed for routing high-frequency analog signals where low and stable on-resistance, controlled off-state isolation, and fast switching behavior are important. A CMOS analog switch is a solid-state semiconductor device that routes analog or digital signals between circuit nodes using voltage-controlled gates. The DG405 family belongs to the broader analog-switch and multiplexer hierarchy, where switch topology, on-resistance, bandwidth, charge injection, and signal-to-noise performance determine whether a device is suitable for precision measurement, communications, instrumentation, or test systems. Unlike mechanical relays, these switches switch without moving contacts and can operate at much higher speeds. The redesigned DG401, DG403, and DG405 family provides guaranteed on-resistance matching between switches of 2 Ω maximum and guaranteed on-resistance flatness over the signal range of 3 Ω maximum. The typical on-resistance is 20 Ω, while the product listing identifies a 45 Ω maximum on-resistance. These characteristics help reduce channel-to-channel error and distortion when a system switches between multiple signal sources or routes a signal to different measurement and processing circuits. The DG405DJ+ uses CMOS circuitry to provide low power consumption and high switching speed. Each of its two channels can function as a 2:1 analog switch, enabling signal selection, channel isolation, test-point routing, and redundant signal paths. Its normally open configuration disconnects the common node while the control signal is inactive, helping prevent unwanted signal propagation when a channel is not selected. Typical uses include audio and communications routing, data-acquisition systems, automated test equipment, sample-and-hold interfaces, and industrial control electronics. The device is particularly appropriate when the signal bandwidth and switching requirements exceed those of basic low-speed analog switches, while the 45 Ω maximum on-resistance remains acceptable for the driven load. Designers should verify the complete electrical limits, control logic levels, switch configuration, and timing behavior in the manufacturer datasheet before finalizing signal paths. Input and output impedances, capacitance, and off-state leakage must be considered together with the 20 Ω typical on-resistance so that switching transients do not degrade accuracy or disturb adjacent high-impedance nodes. This page consolidates the key DG405DJ+ electrical ratings, package information, drop-in identity options, application guidance, and design considerations into one engineering-focused reference. It supports faster component identification while keeping the selection grounded in the manufacturer datasheet and documented device characteristics.
DG408AK - 8:1 CMOS Analog Multiplexer | Analog Devices
Analog Devices DG408AK is a high-performance 8-channel or dual 4-channel CMOS analog multiplexer with 100 ohm maximum on-resistance, 20 pC charge injection, 160 ns transition time, and 10 mA supply current. The device is supplied in a 16-pin CERDIP through-hole package and operates from a single supply, with a maximum supply rating of 44 V. An analog multiplexer is a semiconductor switch that connects one of several analog inputs to a common output. It belongs to the interface IC hierarchy, where it sits between sensors, measurement circuits, data converters, and system control logic. The DG408AK uses three binary select inputs and an enable input to route one of eight channels. It can also be configured as two independent 4-channel multiplexers. Key electrical characteristics include 100 ohm maximum on-resistance, 15 pC maximum charge injection, and a 160 ns transition time. The DG408 family provides TTL-compatible logic control, low power consumption, reduced switching errors, and rail-to-rail signal handling. An improved configuration limits guaranteed on-resistance to 8 ohm and on-resistance flatness to 9 ohm, while input leakage is specified at no more than 100 ohm and 5 nA at 85 degrees Celsius. The DG408AK combines an eight-element CMOS analog-switch array with TTL/CMOS-compatible decoding circuitry and an enable function for cascading or externally controlled devices. Its 3-bit address interface supports straightforward binary channel selection. The switching architecture can be used for multiplexed or demultiplexed signal routing, allowing one measurement amplifier or converter to serve several input channels. Typical uses include data acquisition, instrumentation, battery monitoring, test-equipment signal routing, industrial control, and communications systems. The 44 V maximum supply rating makes the device suitable for systems operating from a single positive supply, while the low-noise switching characteristics help preserve fidelity in high-impedance measurement paths. PCB design should keep analog traces short and provide a stable ground reference. Place input and output decoupling close to the device, route switch-control signals away from sensitive analog nets, and use a common-ground return strategy to minimize switching transients. The manufacturer datasheet pin-description table should be used when assigning all 16 package connections. This product record combines manufacturer specifications, verified package and channel details, pin-level implementation guidance, and clearly qualified drop-in comparisons. It is intended to help engineers evaluate mux routing, timing, leakage, and replacement decisions without relying solely on a distributor catalog summary.
DG409CY+ - Dual 4:1 CMOS Analog Multiplexer | Analog Devices
Analog Devices DG409CY+ is a dual 4:1 CMOS analog multiplexer with two independent 4:1 switch sections, eight bidirectional signal paths, a 100 ohm on-resistance, and a 16-pin SOIC package. According to the Maxim product documentation, the DG409 family provides guaranteed channel matching of 8 ohms maximum and signal flatness of 9 ohms maximum over the specified signal range. An analog multiplexer is a semiconductor switching device that connects one of several analog inputs to a common output. A dual 4:1 configuration contains two independently addressed 4:1 sections, allowing one package to route two sets of four signal sources. In a larger signal-chain hierarchy, the DG409CY+ is a CMOS analog switch, an analog multiplexer, an interface IC, and ultimately a semiconductor used to route signals among sensors, converters, amplifiers, and test equipment. The device operates bidirectionally, so selected channels can carry signals toward the common output or from the output toward a selected input. Its 100 ohm on-resistance supports the routing of moderate-impedance analog signals. The manufacturer also specifies maximum charge injection of 15 pC and improved matching between channels, which are important considerations when switching sampled signals, acquisition channels, or precision control lines. The DG409CY+ is identified as a commercial-temperature 0 °C to +70 °C device in a 16-SOIC package. Typical uses include audio-signal routing, communication systems, data acquisition, guidance and control systems, sample-and-hold circuits, and test equipment. Its two multiplexers can reduce the number of external analog switches required when a board must select among multiple sources. PCB design should preserve the exact pin assignment and routing geometry associated with the selected package variant. Because switching resistance, charge injection, off-state behavior, supply requirements, and control logic determine real-world performance, compare the complete manufacturer data sheet before using the device with high-impedance sources, high-speed sampling systems, or precision measurement circuits. This page consolidates the identified configuration, package, resistance, matching, flatness, charge-injection, temperature, and application characteristics into an engineering-oriented selection guide. It also documents the verified pin-compatible DG409DY+T option and distinguishes device functionality from packaging-only order codes so that design decisions are based on electrical and environmental requirements.
DG412 - Quad SPST CMOS Analog Switch 44V | Analog Devices
The Analog Devices DG412 (originally Maxim Integrated) is a precision monolithic quad SPST CMOS analog switch with four independent single-pole single-throw switches, a maximum supply rating of 44 V, a +/-15 V analog signal range, and on-resistance of 35 to 45 ohm depending on manufacturer grade, housed in a 16-pin SOIC package. An analog switch is a semiconductor device that passes or blocks an analog signal under digital control, acting as a relay replacement without moving parts. Within the signal-path hierarchy, the analog switch sits under signal switching ICs, itself a branch of interface and signal-conditioning semiconductors. Quad SPST devices such as the DG412 integrate four independent switches on one die, letting one logic-controlled part replace four discrete transistor-level switching circuits while preserving signal integrity. Key features include TTL- and CMOS-compatible logic inputs, fast switching with turn-on time around 110 ns per the original datasheet family, ultra-low power dissipation near 0.35 mW quiescent, and improved on-resistance matching between switches of 3 ohm max with guaranteed rDS(on) flatness over the signal range of 4 ohm max in the redesigned Maxim version. The wide 44 V absolute maximum supply rating supports +/-15 V industrial analog rails. Architecturally, the DG412 family uses monolithic CMOS transmission-gate switches with internal level shifting, allowing a single 5 V logic signal to control signals swinging to +/-15 V. Drop-in compatibility with the older DG211/DG212 series simplifies legacy redesigns. Typical applications include audio signal routing, precision test-and-measurement multiplexing, data-acquisition front ends, sample-and-hold circuits, and industrial signal switching where relay-free switching is required. Design consideration: keep control-input logic levels within datasheet limits and observe the analog signal range so switches never see signals beyond the supply rails, which would turn on protection structures and distort the signal. This page synthesizes distributor pricing, verified drop-in alternatives from Analog Devices, Renesas and Vishay, and practical design notes not found in the manufacturer datasheet.
DG412AK - Quad 30Ω SPST Analog Switch | Analog Devices
Analog Devices DG412AK is a quad, single-pole single-throw CMOS analog switch with four independent channels, a 30 Ω on-resistance listing, and a 16-pin CERDIP package. The device is produced for industrial and military-grade applications and is suitable for routing low-frequency analog or digital signals when independent control of four signal paths is required. An analog switch is an integrated semiconductor that connects or disconnects a signal path under digital control. The DG412 belongs to the analog switch hierarchy, which falls within interface ICs and broader semiconductor signal-routing systems. Unlike a mechanical relay, it operates without moving contacts and can support compact signal conditioning, test, measurement, communication, and control circuits. The DG412 family provides four independent SPST switches. The manufacturer's product page identifies low on-resistance matching between channels of 3 Ω maximum and guaranteed on-resistance flatness of Δ4 Ω maximum across the signal range. These characteristics help minimize channel-to-channel variation and signal-level distortion when the same source drives multiple destinations. Distributor listings identify DG412AK as a 16-CERDIP, through-hole device with a nominal 30 Ω or 35 Ω on-resistance listing depending on the manufacturer catalog. The AK package suffix identifies the military temperature-grade version in a hermetically sealed ceramic package. Its four separately controlled switches allow a system to isolate, select, or disconnect external circuits without using four separate relay packages. The 16-pin through-hole format also supports prototype boards, legacy industrial equipment, and repair assemblies where a surface-mount package would be unsuitable. Typical uses include signal-routing modules, test equipment, data-acquisition interfaces, communications equipment, instrumentation, and industrial control systems. Because the switch is normally open, each signal path remains disconnected until its corresponding control input is asserted, helping prevent unintended signal propagation between circuits. When designing around the DG412AK, verify signal amplitude, control logic levels, and switch behavior at the actual operating voltage before finalizing the board. Keep sensitive signal paths short, provide a stable ground reference, and include protection against transient voltages when the switched lines connect to external cables or connectors. This product page consolidates the manufacturer family information, package details, search-driven technical queries, and practical application guidance into a design-oriented reference. It also distinguishes the verified DG412AK characteristics from unresolved pin-level and electrical details that should be confirmed in the manufacturer datasheet before layout release.
DG413DJ+ - Quad SPST Analog Switch | Analog Devices
The Analog Devices DG413DJ+ is a precision monolithic quad SPST CMOS analog switch with four independent channels, a 16-pin PDIP package, and support for dual-supply voltages from 10 V to 30 V or single-supply voltages from 4.5 V to 20 V. It is designed for precision signal routing where consistent on-resistance and low channel-to-channel variation are important. A CMOS analog switch is an integrated semiconductor that connects or disconnects signals under digital control. The SPST configuration provides one normally closed path per channel, while the quad architecture packages four independently controlled switches in one device. Within the broader hierarchy, DG413DJ+ is an analog switch, interface IC, and semiconductor intended for routing low-voltage analog signals in test, measurement, instrumentation, and signal-processing systems. The improved DG413 family provides on-resistance matching between switches of 3 ohms maximum and on-resistance flatness across the signal range of 4 ohms maximum. Its 80-ohm off-state isolation specification helps prevent leakage from inactive channels, while the symmetric switch conduction allows signals to pass effectively in either direction. The operating supply range supports both dual-rail and single-rail circuit architectures. Each channel has a separate TTL- and CMOS-compatible control input, allowing individual signal paths to be routed without changing the main analog topology. The monolithic construction also reduces the number of discrete relays or mechanical contacts required in multi-channel systems. Switching timing and leakage characteristics should be checked against the manufacturer datasheet for the exact operating conditions. Typical uses include multimeter and test-equipment signal routing, data-acquisition front ends, sample-and-hold systems, analog measurement networks, and industrial instrumentation. The four-channel structure is particularly useful when several test points, sensor outputs, or amplifier inputs must be selected electronically under system control. Designers should account for supply sequencing, control-logic levels, analog signal amplitude, leakage, and the power rails available to the switch. A bypass capacitor close to the supply pins helps control supply noise, while keeping sensitive analog routes short reduces susceptibility to interference. Verify that every signal remains within the absolute maximum ratings in the manufacturer datasheet. This page combines the manufacturer product information with engineering-focused comparison data, drop-in alternatives, application guidance, and design notes. It is intended to help engineers select the correct package variant and assess whether the DG413 family matches the channel count, voltage range, logic compatibility, and precision required by a specific analog-routing design.
DG444CY+ - Quad SPST Analog Switch | Analog Devices
Analog Devices DG444CY+ is a four-channel, single-pole single-throw analog switch with a 1:1 signal configuration, 85 ohm on resistance, and a 16-pin SOIC package. The switch provides bidirectional analog channels, power-off isolation, improved on-resistance matching of 4 ohms maximum between switches, and guaranteed on-resistance flatness of 9 ohms maximum across the signal range. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The DG444 family belongs to the analog switch, interface IC, and signal-routing hierarchy. Each of its four independent SPST channels can interrupt or complete a signal route while preserving operation in either signal direction, making the device useful for test systems, signal conditioning, and controlled analog paths. The DG444CY+ emphasizes low and predictable channel resistance. Its 85 ohm on resistance supports practical routing of ordinary low-frequency and control signals, while the 4 ohm maximum matching between switches reduces gain or attenuation differences from one channel to another. The 9 ohm maximum flatness specification limits resistance variation over the operating signal range, helping preserve signal consistency as voltage changes. Power-off isolation prevents the switched paths from conducting when the device is unpowered. The four channels use a 1:1 configuration rather than a multiplexer arrangement, so each channel independently supports a single-pole, single-throw function. This structure is appropriate when the design requires four separate controllable connections rather than time-multiplexed access to fewer signal lines. Typical uses include automated test equipment, instrumentation, signal routing, sample-and-hold systems, and industrial control interfaces. The 16-SOIC surface-mount package allows the same component to support both signal routing and isolation functions on a compact board. The commercial operating-temperature range extends from 0 C to 70 C. For layout, route high-impedance or sensitive signal lines away from digital control traces and place the device so switching transients do not couple directly into adjacent measurement paths. Confirm the complete pin assignment and control logic in the manufacturer data sheet before laying out a new PCB or substituting another DG444 suffix. This page combines the manufacturer product information, distributor listings, family comparison data, practical application guidance, and same-package alternatives. It also highlights where replacement decisions require confirmation of temperature grade, package suffix, and exact on-resistance limits rather than relying on channel count alone.
DP83640TVV/NOPB - IEEE 1588 Ethernet PHY | Texas Instruments
The Texas Instruments DP83640TVV/NOPB is an IEEE 1588 precision-time protocol Ethernet physical-layer transceiver with 10 Mbps and 100 Mbps support, MII and RMII host interfaces, and a 48-pin LQFP (PT) package measuring 7 mm by 7 mm. It is designed for industrial automation and communication systems that require deterministic, low-latency Ethernet time synchronization. The device operates across a -40 °C to +85 °C temperature range. An Ethernet physical-layer transceiver is the circuit that converts digital data into signals suitable for twisted-pair Ethernet cabling and converts received cable signals back into digital data. In the broader hierarchy, the DP83640 is an Ethernet PHY, also described as a network interface transceiver, within interface ICs and semiconductor communications equipment. Adding IEEE 1588 precision timing to a conventional PHY allows network nodes to share a more accurate system time over the Ethernet infrastructure. The DP83640TVV/NOPB supports both MII and RMII connections to a host processor. These interfaces support integration with industrial controllers, embedded systems, test equipment, and communication equipment that already process Ethernet frames digitally. Its 10/100 Mbps capability aligns it with established copper-Ethernet networks rather than multigigabit or fiber-only designs. The 48-LQFP package provides a conventional surface-mount assembly option for industrial control boards. Texas Instruments describes the DP83640 as a Precision PHYTER designed to provide high-precision clock synchronization for real-time industrial connectivity based on IEEE 1588. This makes the device relevant to automation systems where event timing, distributed control, monitoring, and communication between controllers depend on a shared time reference. The manufacturer product page identifies the exact MPN as an IEEE 1588 PTP Ethernet PHY transceiver. Typical uses include industrial Ethernet controllers, synchronized automation networks, factory equipment, networked sensors, industrial communication gateways, and embedded systems performing precise event timestamping. In these systems, the DP83640 can connect an Ethernet physical layer to a host controller through MII or RMII while providing the precision-timing functions needed by IEEE 1588-aware equipment. PCB design must account for the 48-pin LQFP footprint, controlled Ethernet magnetics, high-speed trace routing, impedance continuity, grounding, and power-supply decoupling. Designers should use the manufacturer pin-description table and reference design information when assigning signals, and should preserve the recommended component placement and layout geometry around the PHY and magnetic interface. This product overview consolidates the exact orderable MPN, package, interface, speed, temperature, and lifecycle information with practical selection guidance, application-fit analysis, and design cautions. It also distinguishes the true same-package family variant from broader interface alternatives that do not provide verified pin-to-pin equivalence.
DP83820BVUW - 1GbE PCI Ethernet Controller | Texas Instruments
The Texas Instruments DP83820BVUW is a single-chip 10/100/1000 Mb/s Ethernet controller with a PCI bus interface, 1000 Base-X PHY support, and a 208-QFP package measuring 28 x 28 mm. It operates from a 3.3 V supply and is designed for high-performance PCI adapter cards, motherboards, and embedded systems requiring integrated Gigabit Ethernet connectivity. An Ethernet controller is an interface integrated circuit that manages packet transmission, reception, media access, and host communication. Within the product hierarchy, the DP83820 belongs to Ethernet interface controllers, which combine a network-interface controller, MAC/BIU, and physical-layer interface functions. It also implements the IEEE 802.3 Ethernet standard and supports VLAN, long-frame, and 802.3x flow-control functions. Key features include support for 10, 100, and 1000 Mb/s operation, a 1000 Base-X PHY interface, 64-bit PCI bus mastering at up to 66 MHz, and packet-descriptor DMA that reduces host-CPU processing. The device also supports VLAN-tag insertion and removal for transmitted and received packets, automatic Pause-frame transmission for full-duplex flow control, and long frames for specialized network traffic. Technically, the DP83820 separates packet data movement from host processing through bus-mastering DMA. According to the manufacturer datasheet, the PCI interface implements version 2.2 operation with power-management support. Its supplied current is listed as 150 mA at 3.3 V, while the commercial operating range is reported as 0°C to 70°C. The 208-lead square QFP provides extensive connectivity for the PCI bus, PHY, clocks, and controls. Typical applications include PCI Gigabit Ethernet adapter cards, industrial motherboards, embedded computing platforms, network-interface expansion boards, and legacy PCI systems requiring 1000 Base-X connectivity. Its integrated PHY support is useful when the board design uses a compatible copper or fiber-based 1000 Base-X physical layer rather than a standalone PHY arrangement. Designers should verify the exact transceiver or medium attachment required by the 1000 Base-X interface, validate the PCI connector and termination layout against the manufacturer reference design, and confirm the operating-temperature requirement against the enclosure environment. Tube packaging is specified for the DP83820BVUW, and procurement should account for its large 208-QFP footprint and specialized legacy-PCI application.
DP83822HFRHBR - 10/100 Mbps Ethernet PHY Transceiver | Texas Instruments
The Texas Instruments DP83822HFRHBR is an extended-temperature, robust, low-power 10/100 Mbps Ethernet Physical Layer transceiver housed in a 32-pin VQFN (5 mm × 5 mm) package with fiber (fiber-ready) support and 16 kV HBM ESD protection on the MDI pins. It provides all physical-layer functions needed to transmit and receive data over standard twisted-pair copper cables or to connect to an external fiber-optic transceiver through the MII/RGMII/RMII MAC interface. An Ethernet PHY (Physical Layer Device) is the lowest layer of the OSI networking stack and handles the analog signaling, clock recovery, line coding (MLT-3 / PAM), and link-state machine on the cable side, presenting a digital MII/RMII/RGMII bus to the MAC on the host side. PHYs sit below the MAC, above the magnetics, and below the RJ45 connector; their robustness against ESD, cable discharge, and temperature stress largely determines field reliability of any industrial Ethernet node. Key features include 16 kV HBM ESD on MDI pins, integrated 100BASE-TX/10BASE-TX transceivers, programmable LED outputs, 50 MHz clock output, Energy Efficient Ethernet (EEE) support, Wake-on-LAN (WoL), and extended-temperature operation from −40 °C to +125 °C. The VQFN-32 (RHB) package provides an exposed thermal pad for low thermal resistance and a small PCB footprint for space-constrained designs. The device uses an advanced DSP-based architecture for adaptive equalization, echo cancellation, and cross-talk suppression, supporting both CAT-5 twisted pair and 100BASE-FX fiber media. The "HF" suffix designates the fiber-ready variant of the DP83822 family; the "HR" (RHB) part is copper-only, while "IF" (industrial fiber) variants exist in the same pinout. This flexibility makes the DP83822HFRHBR a pin-to-pin upgradeable option for legacy TLK105/TLK106/TLK105L/TLK106L designs. Typical applications include industrial Ethernet switches, factory-automation PLCs, motor drives, building-automation controllers, PoE PD controllers, security/surveillance IP cameras, and any harsh-environment Ethernet node where copper or fiber link media must coexist on the same PCB layout. It is widely used in IEC 61850 substation gateways and PROFINET nodes. Design considerations include routing the MDI differential pairs with 100 Ω differential impedance and keeping the magnetics within 2 cm of the PHY. An external 25 MHz crystal or oscillator drives the internal PLL, and the 50 MHz clock-out pin can be used to clock a MAC without an additional oscillator. This page synthesizes distributor pricing, drop-in same-package alternatives within the DP83822 family, and practical PCB layout guidance not found in the manufacturer datasheet alone.
DP83822HFRHBT - 10/100 Ethernet PHY, 16kV ESD | Texas Instruments
The Texas Instruments DP83822HFRHBT is a robust, low-power single-port 10/100-Mbps Ethernet physical layer transceiver (Ethernet PHY) with fiber support and 16-kV ESD protection, housed in a 32-pin VQFN (RHB) 5.00 mm x 5.00 mm package rated for -40C to +125C extended temperature operation. An Ethernet PHY (physical layer device) is the interface IC that sits between a media access controller (MAC) and the physical network medium. In the networking hierarchy, it converts digital MAC frames into analog signals suitable for transmission over twisted-pair copper or optical fiber, handling encoding, line drivers, equalization, and auto-negotiation. The DP83822H family extends the standard DP83822HF with extended temperature range and enhanced ESD robustness for harsh environments. Key features include MAC interface flexibility through standard MII, RMII, and RGMII, support for 100BASE-TX and 10BASE-Te over standard twisted-pair cable plus fiber-mode operation via an external fiber transceiver, 16-kV system-level ESD protection, and Energy-Efficient Ethernet (EEE), Wake-on-LAN (WoL), and programmable energy-saving modes. Cable diagnostics and a 50-MHz clock output (RMII reference) simplify system design. Technically, the DP83822H integrates the DSP-based transmit path and adaptive equalizer receiver path required by IEEE 802.3 10/100-Mbps operation, with onboard regulators allowing single-supply design. Its low power consumption suits passively cooled industrial equipment, and pin-to-pin compatibility with TLK105, TLK106, TLK105L, and TLK106L enables drop-in upgrades. Typical applications include industrial Ethernet nodes and EtherCAT slaves, factory automation PLCs, building automation controllers, and grid infrastructure where extended temperature and ESD robustness are mandatory. Design consideration: maintain a clean 3.3-V supply with proper magnetics module selection and follow the datasheet layout guidelines for the analog MDI pairs to guarantee IEEE 802.3 compliance and ESD performance. This page synthesizes verified distributor data, drop-in alternatives within the DP83822/TLK families, and practical design guidance not consolidated in the manufacturer datasheet alone.
DP83822IFRHBR - 10/100Mbps Ethernet PHY 16kV ESD | TI
The Texas Instruments DP83822IFRHBR is a low-power, robust 10/100-Mbps Ethernet physical layer transceiver (Ethernet PHY) with fiber support and 16-kV IEC ESD protection, housed in a 32-pin VQFN (RHB) 5.00 mm x 5.00 mm package rated from -40C to +85C. An Ethernet PHY transceiver is the physical-layer device in the Ethernet stack that converts digital MAC data into signals suitable for transmission over twisted-pair copper or optical fiber media. In the network hierarchy, the PHY sits between the Media Access Controller (MAC) and the physical medium, handling encoding, line driving, equalization, and link detection per the IEEE 802.3 10BASE-Te/100BASE-TX standards. Ethernet PHYs are foundational building blocks of industrial automation, factory networking, and connected embedded systems. Key features of the DP83822IFRHBR include low power consumption enhanced by Energy-Efficient Ethernet (EEE), Wake-on-LAN (WoL), and programmable energy-saving modes; 16-kV system-level ESD robustness for harsh industrial environments; fiber-optic media support in the IF variant; and pin-to-pin upgradeability from the TLK105, TLK106, TLK105L, and TLK106L 10/100-Mbps Ethernet PHYs. These characteristics reduce system power budgets and improve reliability in electrically noisy installations. Architecturally, the DP83822 integrates the analog line drivers, receivers, and adaptive equalization needed for robust 100BASE-TX links, together with a standard MII/RMII/SNI serial management interface for connection to virtually any MAC or FPGA-based MAC implementation. Programmable LED outputs, interrupt support, and extensive register-level configuration allow fine-grained control of link behavior and diagnostics. Typical applications include industrial Ethernet nodes such as PLCs, motor drives, and I/O modules; building automation and security cameras; and general embedded networking where 10/100-Mbps connectivity, low power, and ESD robustness are required. The fiber-supported IF variant suits electrically hostile or long-distance links. For design, provide a stable 3.3V supply domain with proper decoupling and follow TI's reference layout guidance for the magnetics and MDI routing to preserve signal integrity and ESD performance. This page synthesizes distributor listings, cross-reference research, and practical drop-in alternative analysis not found on the manufacturer datasheet alone.
DP83826AE - Low-Latency 10/100 Ethernet PHY for EtherCAT | TI
The Texas Instruments DP83826AE is a deterministic, low-latency, low-power 10/100 Mbps Ethernet PHY transceiver optimized for EtherCAT industrial Ethernet applications, housed in a 32-pin VQFN (5x5 mm) package with MII/RMII serial management interfaces and an extended operating temperature range. An Ethernet PHY (physical layer transceiver) is the IC that bridges the digital MAC of a microcontroller or FPGA and the copper twisted-pair cable medium. Within the network hierarchy, the PHY sits below the MAC and above the magnetics and connector, encoding and decoding 10BASE-Te and 100BASE-TX frames per IEEE 802.3. In industrial automation, PHY latency and latency determinism directly affect cycle times and jitter in protocols such as EtherCAT, making PHY selection a system-level performance decision. Key features of the DP83826AE include low and deterministic transmit-to-receive latency, support for 10BASE-Te and 100BASE-TX Ethernet protocols, MII and RMII media-independent interfaces for flexible MAC connectivity, and an extended temperature rating suited to harsh factory-floor environments. According to TI, the DP83826Ax family was specifically characterized to meet the stringent timing requirements of real-time industrial Ethernet systems, where propagation delay variation must be minimized and predictable. Technically, the device integrates the analog line drivers, equalizers, clock recovery, and adaptive filtering required for robust Category-5 cable operation, while consuming low power to support dense multi-port industrial I/O. The RMII mode reduces pin count and controller overhead, while MII supports legacy MAC implementations. per TI's product comparison tool, the DP83826AE sits alongside the DP83826E, DP83826I, and DP83822H in TI's industrial PHY portfolio, with the AE variant optimized for EtherCAT timing and extended temperature. Typical applications include EtherCAT slave controllers in servo drives, 6-axis robot arms, industrial vision systems such as those from Hanwha Vision, PLC communication modules, and machine-vision cameras requiring deterministic sub-microsecond network timing. For design, ensure correct reset pin handling - the active-low reset requirements of the DP83826E and DP83826AE are discussed in TI E2E support threads, and magnetics selection should follow the datasheet reference design. This page adds value beyond the manufacturer datasheet by consolidating drop-in alternatives, pricing references, and practical design guidance in one place.
DP83847ALQA56A - 10/100 Ethernet PHY | Texas Instruments
The Texas Instruments DP83847ALQA56A is a single-channel 10/100-Mbps Ethernet physical-layer transceiver with integrated PMD sublayers, designed for 10BASE-T and 100BASE-TX Ethernet communication over Category 3 or Category 5 unshielded twisted-pair cables. The device operates from a 3 V to 3.6 V supply, includes 5 V tolerant I/O, and is packaged in a 56-WQFN 9 x 9 mm surface-mount package. An Ethernet PHY is the physical-layer component in an Ethernet communications hierarchy. It converts logical data transmitted by a MAC or network controller into electrical signals for twisted-pair cabling and converts received signals back into digital data. The DP83847 supports the 10 Mb/s and 100 Mb/s Ethernet rates defined for its 10BASE-T and 100BASE-TX modes, while Parallel Detection helps determine the connection type and link status during Auto-Negotiation. The DP83847 uses low-power 0.18 µm CMOS technology and is specified for typical power consumption below 351 mW. Its 5 V tolerant I/O structure allows the digital interface to connect to systems using higher logic levels while the core operates from the 3.3 V supply range. The device includes an external twisted-pair transformer interface, making it suitable for Ethernet PHYs used in industrial, office, home, and embedded networking equipment. The manufacturer documentation identifies the DP83847 as a full-feature single Physical Layer device with integrated PMD sublayers. It supports 10BASE-T and 100BASE-TX protocols, Parallel Detection under IEEE 802.3u, and hardware reset-controlled configuration through latched float and pull-down pins. The electrical design requires careful attention to the external magnetics, line impedance, termination, decoupling, and signal routing on the printed circuit board. Typical applications include industrial Ethernet controllers, embedded Linux systems, factory automation equipment, network interface controllers, print servers, IP cameras, and communications equipment requiring 10/100-Mbps copper Ethernet. A system implementation must provide the required external transformer and suitable RJ45 or cable-side interface while observing the device’s pin configuration and power-supply recommendations. For PCB design, place the PHY, transformer, and supporting passive components according to the manufacturer’s recommended layout, keep high-current and high-speed paths controlled, and provide local supply bypassing close to the power pins. Use the manufacturer datasheet for the definitive pin assignment, package dimensions, timing characteristics, and electrical limits before releasing production hardware. This product page consolidates the manufacturer’s technical description, lifecycle information, package details, application guidance, and verified cross-reference information. It distinguishes the obsolete DP83847ALQA56A from the documented direct substitute DP83847ALQA56A/NOPB while avoiding unsupported assumptions about additional replacement parts.
DP83848KSQ/NOPB - 10/100 Ethernet PHY, WQFN-40 | Texas Instruments
The Texas Instruments DP83848KSQ/NOPB is a single-port 10/100 Mbps Ethernet physical layer transceiver (PHY) in a 40-pin WQFN (6x6 mm) package. It implements the IEEE 802.3u standard for 100BASE-TX and 10BASE-T, providing a complete physical layer solution with MII (Media Independent Interface) and RMII connectivity to a MAC controller. Operating from a 3.3V supply, the device is targeted at industrial and embedded networking applications. An Ethernet PHY is the physical layer transceiver that interfaces between a digital MAC (Media Access Controller) and the physical twisted-pair cable. It handles encoding, serialization, line driving, and reception of Ethernet frames. The DP83848x family belongs to the PHYTER series, within the broader hierarchy of Ethernet interface ICs -> network interface ICs -> communication interface ICs -> integrated circuits. Key features include Auto-MDIX for automatic crossover detection, eliminating the need for crossover cables. The device supports both 10BASE-T and 100BASE-TX with performance exceeding IEEE specifications, including operation beyond 137 meters of Cat-V cable. It offers low power consumption and a small footprint suitable for space-constrained designs, with industrial temperature support from -40C to +85C. The DP83848K integrates a digital adaptive equalizer, echo canceller, and baseline wander correction to ensure reliable data transmission. The device includes an MDIO serial management interface for configuration and status monitoring, with support for dynamic control of Auto-MDIX and LED indicators. The architecture is built on a low-power 3.3V CMOS process, achieving IEEE 802.3u compliance. Typical applications include industrial control systems, embedded networking, IP cameras, IoT gateways, factory automation controllers, and building automation. The industrial temperature range makes it suitable for harsh environments such as outdoor enclosures, machine-to-machine communication, and test equipment with extended thermal requirements. When designing with this PHY, ensure proper isolation transformer selection and 50 ohm termination resistors for the magnetics interface. Careful PCB layout is required to minimize EMI and maintain signal integrity on the differential pairs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DP83849IDVS/NOPB - Dual-Port 10/100 Ethernet PHY | Texas Instruments
The Texas Instruments DP83849IDVS/NOPB is an industrial-temperature, dual-port 10/100-Mbps Ethernet PHY transceiver with fiber support, packaged in an 80-pin TQFP (PFC) package measuring 12 x 12 mm. It provides two transmit and two receive channels for copper or fiber-based Ethernet connectivity, operates across -40°C to +85°C, and is designed for embedded networking equipment that requires multiple physical-layer interfaces. An Ethernet PHY transceiver is the physical-layer component that converts digital Ethernet data into electrical or optical signaling and receives incoming signaling for conversion into digital data. Within the network hierarchy, this device belongs to Ethernet transceivers, physical-layer devices, interface ICs, and semiconductor components. It connects an Ethernet MAC or network processor to physical media through integrated drivers, receivers, clocking, and auto-negotiation functions. The DP83849IDVS/NOPB supports 10/100-Mbps operation on two independent ports. Its dual-channel architecture reduces the number of separate PHY devices required in routers, industrial controllers, network switches, and test equipment. Industrial-temperature operation makes it suitable for systems expected to operate across a broad ambient range, while the 80-pin TQFP construction supports conventional surface-mount assembly and multilayer PCB routing. Fiber support extends the design beyond copper cabling and allows optical-network-interface circuitry to be connected to the PHY where appropriate. A complete Ethernet design still requires external magnetics, isolation components, connectors or fiber transceivers, a stable supply, suitable decoupling, and a compliant signal-integrity layout. The PHY does not replace the external passive network components required at the cable or fiber interface. Typical uses include industrial Ethernet gateways, dual-port embedded controllers, network-interface cards, optical network equipment, factory automation controllers, and communications infrastructure. The device can be especially useful where two 10/100 ports are required without allocating two separate PHY packages or where industrial temperature performance is required rather than a consumer-temperature alternative. Design the power, clocks, magnetic components, and medium-dependent interfaces directly from the manufacturer datasheet. Keep the PHY and its support network on a controlled impedance layer, provide the required local bypass capacitors, and maintain the specified clock and reset sequencing. Confirm the complete pin assignment and exposed thermal-pad connection on the official package drawing before fabrication. This product record combines the manufacturer’s device classification, package and temperature information, distributor listing details, and practical Ethernet design guidance. It also distinguishes true package-compatible alternatives from broader functional equivalents so engineers can assess PCB reuse, media support, and operating-temperature requirements before committing to a replacement.
DP83849IFVS/NOPB - Dual 10/100 Ethernet PHY | Texas Instruments
The Texas Instruments DP83849IFVS/NOPB is a dual-port 10/100 Mb/s Ethernet physical-layer transceiver with fiber support and flexible port switching, supplied in an 80-pin TQFP (PFC) package measuring 12 mm by 12 mm. It supports a 3 V to 3.6 V supply, provides two transmit and two receive channels, and operates from -40C to 85C for industrial-temperature designs. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts logical data from an Ethernet controller into signals that can traverse copper cabling or fiber media. It also receives analog signaling from the network and converts it into digital data for the controller. As a dual-port PHY, the DP83849IFVS/NOPB can manage two independent 10/100 Mb/s Ethernet links while sharing one host-facing interface. The device is differentiated by its fiber-support capability, industrial-temperature range, and flexible port switching. These characteristics allow a single physical-layer device to serve copper and fiber-facing equipment designs where separate PHY solutions would otherwise be required. Its two-channel architecture also supports dual-port networking equipment with a more compact component footprint than two unrelated PHYs. The DP83849 family is positioned between a media-access controller and the physical network medium. A controller handles frame processing, addressing, and protocol activity, while the PHY performs electrical signaling, line coding, link negotiation, and physical-layer status reporting. Separating these functions lets manufacturers reuse a host controller while selecting the PHY appropriate for the required media, temperature range, and port arrangement. Typical uses include industrial Ethernet switches, factory automation equipment, embedded gateways, serial-to-Ethernet systems, optical-network interfaces, and dual-port industrial controllers. Fiber support is particularly useful when equipment must communicate across electrically noisy factory environments or over longer cable runs. The industrial temperature rating also makes the device suitable for equipment operating outside typical commercial environmental conditions. PCB implementation must preserve the pin assignments and high-speed signal-routing conditions defined by the manufacturer. Keep the Ethernet differential pairs routed with continuous reference planes and controlled impedance, place termination and magnetic-component footprints where specified, and isolate analog, digital, and power-supply return currents. Confirm every pin connection and supply requirement against the manufacturer datasheet before releasing the PCB. This product record combines the official device description, package and environmental specifications, supported interface roles, practical industrial-networking applications, and verified drop-in references. It is intended to accelerate component selection while preserving the engineering checks required for a reliable Ethernet physical-layer implementation.