Interface ICs
ژێرپۆلەکان
بەرهەمەکان (560+)
ISD9361RI - Serial Voice Record/Playback IC, 64-LQFP | Nuvoton
The Nuvoton Technology ISD9361RI is a serial-interface voice record and playback IC (Message Serial series) supplied in a 64-pin LQFP package measuring 7 x 7 mm, rated for an operating temperature range of -40C to +85C. The device integrates the analog audio front end and message management logic required to record and play back voice messages under serial control from a host microcontroller. A voice record and playback IC is a mixed-signal audio device that converts microphone input into stored digital audio and converts stored digital data back into analog sound using an integrated codec, speaker driver interface, and message indexing engine. Such devices sit within the broader hierarchy of audio codec ICs and human-machine-interface semiconductors, where they offload audio capture and playback tasks from the main processor. Key features of the ISD9361RI include its serial host interface, message-based storage architecture for indexed voice segments, integrated record and playback paths, industrial-grade temperature rating from -40C to +85C, and a compact 7 x 7 mm 64-LQFP surface-mount package that suits dense PCB layouts. The message-serial architecture allows a host controller to address individual voice messages, enabling prompt-driven user interfaces without streaming raw audio data over the bus. Technically, the device combines an analog front end for microphone and line inputs with a digital message-management core, providing self-contained record/playback sequencing. Host controllers issue serial commands to trigger specific messages, simplifying firmware in applications that only need canned announcements or prompt playback. Typical applications include industrial equipment voice annunciators, medical device audible prompts, security and alarm announcement panels, elevator and building-automation voice prompts, and consumer appliance user interfaces. Design consideration: because the ISD9361RI is officially listed as obsolete, new designs should secure long-term stock or plan a successor strategy before committing to this part; verify message storage duration and audio bandwidth against the manufacturer datasheet. This page synthesizes distributor stock data, lifecycle status, and sourcing guidance for an obsolete Nuvoton voice IC - information not consolidated in the manufacturer datasheet.
ISL33001IUZ - I2C Bus Buffer, Hot-Swap 2-Ch | Renesas
The Renesas Electronics ISL33001IUZ is a 2-channel I2C bus buffer with rise-time accelerators and hot-swap capability, extending I2C bus capacitance beyond the 400 pF limit specified by the I2C specification, supplied in an 8-pin MSOP (IUZ) package rated for the industrial -40C to +85C temperature range. An I2C bus buffer (also called a bus repeater or signal buffer) is an interface IC that sits between an I2C controller segment and a heavily loaded peripheral segment. The I2C specification limits total bus capacitance to 400 pF, which restricts the number of devices, trace length, and pull-up resistance a system can support. A bus buffer regenerates the SDA and SCL edges, segmenting the bus so each side only sees its own local capacitance, allowing much larger backplanes, card cages, and cable runs. Key features of the ISL33001 include two independent buffered channels (SDA and SCL), rise-time accelerator circuitry that drives rising edges actively to reduce power dissipated in passive pull-up resistors and enable faster data rates, and integrated hot-swap circuitry that prevents SDA/SCL corruption when a board is inserted into or removed from a live backplane. The device supports standard and fast-mode I2C operation with level-tolerant I/O structure. Architecturally, the buffer uses a dual-direction translator between the controller-side and card-side pins: a low level on either side propagates to the other, while levels are re-driven with controlled rise times. This bidirectional, transparent behavior requires no mode control in typical single-controller systems. The hot-swap input stage holds the local bus pins low or high-impedance during power ramp until VCC stabilizes, avoiding spurious start or stop conditions during card insertion. Typical applications include server and telecom backplanes, I2C fan controllers, optical-module management (SFP/QSFP style management buses), battery-management and hot-pluggable card rails, and long cable runs between chassis in industrial systems. Design consideration: rise-time accelerators pull up only during edges; ensure adequate static pull-up resistance on the far side of the buffer for DC low-level sinks, and keep the EN/enable pin controlled during power sequencing to avoid bus glitches. This page synthesizes distributor pricing, drop-in family alternatives (ISL33002/ISL33003), and practical design notes not found in the manufacturer datasheet.
ISL33002IUZ-T - 2-Ch I2C Bus Buffer Hot-Swap | Renesas
The Renesas Electronics ISL33002IUZ-T is a two-channel bidirectional I2C bus buffer with rise-time accelerators and hot-swap capability, operating from a +2.3V to +5.5V supply at over 400kHz, housed in an 8-lead MSOP package. An I2C bus buffer, also called a bus accelerator or signal repeater, is an interface IC that regenerates the SDA and SCL signals so the total bus capacitance can exceed the 400pF limit defined by the I2C specification. Within the signal-chain hierarchy (buffer -> interface IC -> signal buffer/repeater), bus buffers isolate capacitance on either side of the device, allowing long cables, large backplanes, and high fan-out systems to communicate reliably at standard I2C data rates. Key features include bus capacitance buffering beyond the 400pF I2C maximum, rise-time accelerator circuitry that reduces power consumption otherwise wasted in passive pull-up resistors while improving data-rate performance, hot-swap circuitry that prevents bus corruption during live card insertion, and robust ESD protection of ±6kV Class 3 HBM on all pins, with ±12kV HBM on the SDA/SCL pins. The device supports logic level translation between voltage domains, includes an accelerator disable pin for flexible system control, and provides low quiescent current. Operation over an industrial -40C to +85C temperature range makes the -T (tape-and-reel, industrial temperature grade) variant suitable for factory and telecom equipment. The 8 Ld MSOP occupies only 3mm x 3mm of board area. Typical applications include I2C bus extension across backplanes and racks, hot-swappable line cards, level translation between 1.8V/3.3V/5V domains, and server or networking chassis management buses (such as IPMB-style monitoring). The buffer fits wherever capacitance, cable length, or card insertion would otherwise corrupt I2C signaling. A key design consideration: enable the accelerator circuit only when bus rise times are marginal with the chosen pull-up resistors, since excessive acceleration can cause signal ringing on lightly loaded buses. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ISL33003IUZ-T - I2C Bus Buffer, Hot-Swap, 8-MSOP | Renesas
The Renesas Electronics ISL33003IUZ-T is a two-channel I2C bus buffer with rise-time accelerators and hot-swap capability, supplied in an 8-MSOP surface-mount package for industrial -40C to +85C operation. An I2C bus buffer (also called a bus repeater or signal buffer) is an interface IC that regenerates the two-wire SDA and SCL signals of an I2C bus, extending the total bus capacitance beyond the 400 pF limit specified by the I2C specification. Within the interface IC hierarchy (bus buffer -> signal buffer/repeater -> interface IC -> semiconductor), buffers let designers add more devices, longer cables, and larger PCB traces to an I2C segment without sacrificing signal integrity or data-rate performance. Key features of the ISL33003 include capacitance extension beyond the 400 pF I2C limit, rise-time accelerator circuitry that reduces the power consumed by passive pull-up resistors while improving data-rate performance, and hot-swap circuitry that prevents corruption of the bus during card insertion or removal. The two channels allow buffering of both SDA and SCL in one compact 8-MSOP package. Technically, the buffer separates capacitive loading on either side of the device, isolating a heavily loaded segment from the controller segment. The rise-time accelerators actively pull the bus lines high during transitions, allowing weaker (higher-value, lower-power) pull-up resistors to be used without slowing edge rates. The hot-swap function keeps the I/O pins high-impedance until the local supply stabilizes, avoiding bus latch-up or data corruption during live insertion. Typical applications include backplane and card-cage systems with pluggable I2C cards, server and telecom chassis management (I2C/PMBus sensor rails), and long bus runs in industrial control where many EEPROMs, RTCs, or I/O expanders share one bus. Design consideration: place the buffer physically between the capacitive segments, and follow the datasheet recommendations for pull-up sizing and accelerator enable configuration to avoid false START conditions. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.
ISL84051IA - 8:1 100 Ohm Analog Multiplexer | Renesas
Renesas Electronics ISL84051IA is a low-voltage, single 8-to-1 analog multiplexer with an on-resistance of 100 ohms, TTL/CMOS-compatible control inputs, and a 16-QSOP package. It supports single-supply operation from 2 V to 12 V and dual-supply operation, allowing one multiplexed analog path to select among eight signal sources. An analog multiplexer is a semiconductor switch that routes multiple input signals to one common output. It belongs to the analog switch and multiplexer hierarchy, where a multiplexer reduces the number of external connections needed by a data-acquisition system. The ISL84051IA combines an 8-to-1 signal configuration, selectable signal polarity, and an inhibit function within a compact surface-mount package. Principal features include an 8-to-1 configuration, 100-ohm maximum on-resistance as listed by distributors, TTL/CMOS-compatible logic inputs, and operation from 2 V to 12 V. The device can also operate from dual supplies, making it suitable for systems that must route signals centered around ground. Its low-voltage design supports analog measurement, test, and signal-routing equipment. The ISL84051 family is designed as a pin-compatible replacement for MAX4051 and MAX4051A devices. Control logic determines which one of the eight analog inputs connects to the common output, while the inhibit pin can disconnect all signal paths. This architecture reduces input-channel count on analog-to-digital converter boards and permits several sensors or voltage sources to share one conversion channel. Typical uses include battery-cell measurement, automated test equipment, data-acquisition systems, sample-and-hold networks, and general-purpose analog routing. Designers should account for on-resistance when calculating signal attenuation, confirm that the selected supply configuration meets the input voltage range, and treat the inhibit function as a deliberate control signal rather than a substitute for power sequencing. PCB placement should keep analog traces short and provide a nearby ground return to minimize parasitic pickup. Input and output protection may be required when connected to external sources. The manufacturer datasheet should guide logic-level compatibility, supply sequencing, and handling of unused channels. This page combines device specifications, verified drop-in cross-references, application guidance, and package-specific selection information to support faster engineering evaluation and sourcing decisions.
ISO1042 - Isolated CAN Transceiver with 70V Fault Protection | TI
The Texas Instruments ISO1042 is a galvanically-isolated controller area network (CAN) transceiver that meets the specifications of the ISO11898-2 (2016) standard. It offers ±70V DC bus fault protection and ±30V common-mode voltage range, making it robust for industrial and automotive networking. The device supports data rates up to 5 Mbps in CAN FD mode, enabling faster payload transfer compared to classic CAN. It is available in an 8-pin SOIC (DW) package and operates over a wide temperature range. A CAN transceiver is a physical-layer device that interfaces between the CAN protocol controller and the differential bus lines. It converts the digital signals from the controller into differential signals for transmission and vice versa. The ISO1042 adds galvanic isolation, which separates the bus side from the logic side, preventing ground loops and protecting low-voltage electronics from high-voltage transients. This isolation is critical in industrial environments where long bus lines and potential ground potential differences exist. Key features include reinforced isolation with a working voltage of 1000 Vrms, a common-mode voltage range of ±30V, and bus fault protection up to ±70V. The device also features a silent mode for bus monitoring and a dominant timeout function to prevent bus lock-up. Its low loop delay of 150 ns ensures high-speed communication, and it is compliant with ISO11898-2 (2016) and ISO11898-5 standards. The ISO1042 uses TI's capacitive isolation technology, which provides high immunity to magnetic interference and supports high data rates. The isolation barrier is rated for 5000 Vrms surge, ensuring reliable operation in harsh environments. The device is designed for use in automotive and industrial applications, including electric vehicles, battery management systems, and factory automation. Typical applications include automotive body control modules, industrial fieldbus networks, and building automation. The ISO1042 is also suitable for solar inverters and motor drives where galvanic isolation is required for safety. Its robust fault protection and high common-mode range make it ideal for long bus lines in noisy environments. When designing with the ISO1042, ensure proper PCB layout with adequate creepage and clearance distances for the isolation barrier. Use a 100 nF bypass capacitor on the VCC pin and a 10 µF capacitor on the VIO pin for stable operation. The device requires a single 3.3V or 5V supply on the logic side and a 5V supply on the bus side.
ISO1042BDWV - Isolated CAN FD Transceiver 5Mbps 70V | TI (Tape & Reel)
The Texas Instruments ISO1042BDWV is a galvanically-isolated CAN transceiver supporting flexible data rates up to 5 Mbps (CAN FD capable), with 70-V bus fault protection and a working isolation voltage of 1060 Vrms, housed in an 8-pin wide-body SOIC (DWV) package rated from -40C to +125C. A CAN transceiver is the physical-layer interface device that translates logic-level signals from a CAN controller into differential bus signals (CANH/CANL) and back. Within the system hierarchy it sits between the protocol controller and the twisted-pair bus, and isolated variants like the ISO1042 belong to the broader class of digital-isolator-based interface ICs used in industrial and automotive networks. Key features include 70-V bus fault protection (far beyond the -27V to 40V tolerance of typical transceivers), a 5 Mbps flexible data rate for CAN FD frames, and logic-side supply flexibility from 1.8V to 5.5V, allowing direct connection to low-voltage microcontrollers without level shifting. Integrated bus-pin ESD protection of +/-16 kV HBM, thermal shutdown, and dominant-timeout functions further harden the interface. Architecturally, the device integrates the TX and RX signal isolation channels across TI's capacitive isolation barrier plus the CAN bus driver/receiver in one package, eliminating a separate digital isolator in front of a standard transceiver. The low loop delay of 152 ns supports longer bus lengths and faster arbitration in CAN FD communication, and the device meets ISO11898-2 (2016) standard specifications. Typical applications include industrial automation and motor drive networks, building automation, NVIDIA Jetson-style embedded compute platforms requiring a CAN FD isolator, automotive body electronics (the ISO1042BQDWVRQ1 variant), and medical equipment needing safety isolation between controller and bus. For design, maintain creepage and clearance around the isolation barrier in PCB layout, supply the logic side at 1.8V or 5.5V as specified, and place the 120-ohm bus termination per standard CAN practice. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing at authorized distributors starts near $0.77 as of 2026-09-01.
ISO1042BDWVR - Isolated CAN FD Transceiver 5Mbps 70V | TI
The Texas Instruments ISO1042BDWVR is a galvanically-isolated CAN transceiver supporting flexible data rates up to 5 Mbps (CAN FD capable), with 70-V bus fault protection and a working isolation voltage of 1060 Vrms, housed in an 8-pin wide-body SOIC (DWV) package rated from -40C to +125C. A CAN transceiver is the physical-layer interface device that translates logic-level signals from a CAN controller into differential bus signals (CANH/CANL) and back. Within the system hierarchy it sits between the protocol controller and the twisted-pair bus, and isolated variants like the ISO1042 belong to the broader class of digital-isolator-based interface ICs used in industrial and automotive networks. Key features include 70-V bus fault protection (far beyond the -27V to 40V tolerance of typical transceivers), a 5 Mbps flexible data rate for CAN FD frames, and logic-side supply flexibility from 1.8V to 5.5V, allowing direct connection to low-voltage microcontrollers without level shifting. Integrated bus-pin ESD protection of +/-16 kV HBM, thermal shutdown, and dominant-timeout functions further harden the interface. Architecturally, the device integrates the TX and RX signal isolation channels across TI's capacitive isolation barrier plus the CAN bus driver/receiver in one package, eliminating a separate digital isolator in front of a standard transceiver. The low loop delay of 152 ns supports longer bus lengths and faster arbitration in CAN FD communication, and the device meets ISO11898-2 (2016) standard specifications. Typical applications include industrial automation and motor drive networks, building automation, NVIDIA Jetson-style embedded compute platforms requiring a CAN FD isolator, automotive body electronics (the ISO1042BQDWVRQ1 variant), and medical equipment needing safety isolation between controller and bus. For design, maintain creepage and clearance around the isolation barrier in PCB layout, supply the logic side at 1.8V or 5.5V as specified, and place the 120-ohm bus termination per standard CAN practice. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing at authorized distributors starts near $0.77 as of 2026-09-01.
ISO1042BQDWQ1 - 5 Mbps Isolated CAN FD Transceiver | Texas Instruments
The Texas Instruments ISO1042BQDWQ1 is an automotive, galvanically isolated CAN transceiver with integrated bus fault protection, designed for Controller Area Network communication in vehicle electronics and other electrically noisy environments. It supports CAN FD operation up to 5 Mbps and complies with the ISO11898-2 (2016) CAN standard. The device is available in a 16-pin SOIC package, with the ISO1042BQDWQ1 ordering code identifying the tube-packaged automotive variant. A CAN transceiver is an interface circuit that converts logic-level signals from a controller into differential CAN bus signals and converts received bus signals back into logic-level data. Galvanic isolation places a physical isolation barrier between the logic-side circuitry and the CAN bus side, helping prevent ground-potential differences and high-voltage transients from propagating into the host electronics. The ISO1042-Q1 family is used in automotive networks where robust fault handling and reliable differential signaling are important. The ISO1042-Q1 family provides plus-or-minus 70 V DC bus fault protection and a plus-or-minus 30 V common-mode voltage range. These protections increase resilience against transient bus faults, wiring errors, and ground-offset conditions encountered in long vehicle harnesses. The transceiver also supports CAN FD operation at up to 5 Mbps, allowing systems to carry larger payloads and achieve faster update rates than classic CAN communication. The ISO1042BQDWQ1 is identified as an automotive-qualified member of the ISO1042-Q1 family. The Q1 designation identifies the automotive product line, while the DW package designation corresponds to the 16-pin SOIC outline. The isolation barrier and integrated bus protection make the device suitable for CAN communication between a host controller and a vehicle network, particularly where the bus may be separated from the controller ground domain. Typical applications include electric-vehicle powertrain controllers, body and comfort modules, battery-management systems, automotive infotainment gateways, industrial CAN FD gateways, and isolated diagnostic interfaces. In a complete CAN link, the transceiver is placed between the CAN controller and the differential CANH and CANL conductors. The bus-side connection must be designed to minimize stub effects, maintain the intended termination network, and provide appropriate surge and ESD protection for the installation environment. When selecting this part, verify the complete pin configuration, isolation ratings, supply requirements, timing characteristics, and automotive qualification requirements against the manufacturer datasheet. The key design trade-off is the added protection and isolation of the bus interface versus the component count and propagation delay introduced by an isolated transceiver. For a replacement, use the manufacturer pinout and parameter comparison rather than relying only on package similarity. This page provides an engineering-focused summary of the ISO1042-Q1 CAN FD transceiver, including application guidance, package information, verified manufacturer and distributor references, and drop-in comparison candidates.
ISO1042BQDWVQ1 - 5Mbps Isolated CAN FD Transceiver | TI
The Texas Instruments ISO1042BQDWVQ1 is an automotive-grade, galvanically isolated CAN bus transceiver supporting data rates up to 5 Mbps in CAN FD mode. It provides one CAN driver and one receiver in an 8-pin SOIC package, operates from 4.5 V to 5.5 V, and meets the ISO11898-2:2016 controller area network standard. The isolation barrier separates the CAN bus interface from the logic-side circuitry, helping protect sensitive systems from ground-potential differences and electrical faults. A CAN transceiver is an interface IC that converts digital controller signals into CAN bus levels and converts received bus levels back into logic-compatible signals. In the broader product hierarchy, it belongs to the CAN transceiver class within interface ICs and communication semiconductors. The ISO1042-Q1 family supports both classic CAN and CAN FD operation, making it suitable for automotive electrical systems and other isolated CAN networks that need higher payload throughput. Key electrical features include up to 5 Mbps data rate, ±70 V DC bus-fault protection, and a ±30 V common-mode operating range. The 120 mV receiver hysteresis improves noise immunity around the decision threshold. These characteristics are particularly valuable in vehicle electrical environments, where transients, ground shifts, and wiring faults can place unusual voltages on a CAN network. The device uses a galvanically isolated CAN interface with separate bus-side and logic-side supply domains. Its half-duplex architecture supports one transmitter and one receiver for conventional CAN bus nodes. ISO11898-2:2016 compliance provides a defined baseline for physical-layer behavior, while CAN FD support extends the usable payload rate compared with classic CAN. Designers must still provide appropriate bus termination, common-mode choke components, decoupling, and isolation-rated board-layout practices. Typical uses include electric-vehicle powertrain networks, body and comfort modules, battery-management systems, charging interfaces, industrial automation equipment, and other isolated CAN nodes. The package is particularly appropriate where a compact 8-pin surface-mount implementation is required and the bus environment demands stronger fault protection than a basic non-isolated transceiver provides. When laying out the circuit, place each supply-domain decoupling capacitor close to its associated power pins and keep the isolation barrier free of high-speed digital return currents. Use the manufacturer datasheet pin-description table when assigning PCB tracks, and verify component spacing, creepage, clearance, and capacitor ratings against the isolation requirements of the final equipment. This page consolidates the key electrical limits, automotive qualification, package information, application guidance, drop-in alternatives, and practical design considerations for engineers evaluating the ISO1042BQDWVQ1 across industrial and automotive CAN FD networks.
ISO1042BQDWVRQ1 - 5Mbps Isolated CAN FD Transceiver | TI
The Texas Instruments ISO1042BQDWVRQ1 is an AEC-Q100 qualified, galvanically-isolated CAN FD transceiver supporting data rates up to 5 Mbps, with ±70-V DC bus fault protection and a ±30-V common-mode voltage range, housed in an 8-pin wide-body SOIC (DWV) package. An isolated CAN transceiver is a signal interface IC that combines a CAN physical-layer transceiver with a digital isolator in a single package. In the system hierarchy, it sits between the host microcontroller or CAN controller (logic side) and the two-wire CAN bus (bus side), providing galvanic isolation that blocks ground loops, common-mode transients, and high-voltage faults - critical in vehicles and industrial networks where nodes span large distances and different ground domains. Key features include support for CAN FD flexible data rates up to 5 Mbps, enabling much faster payload transfer than classic CAN's 500 kbps; a logic-side supply range down to 1.8 V for direct interfacing with low-voltage MCUs; and robust protection with ±70-V DC bus fault tolerance. The device meets the ISO11898-2 (2016) standard and integrates one driver and one receiver channel with typical operating supply current of about 43 mA. The ISO1042-Q1 family uses TI capacitive isolation technology, providing a reliable galvanic barrier suited to automotive and industrial environments. The wide-body SOIC-8 (DWV) package provides substantial creepage and clearance distance across the isolation barrier, supporting basic and reinforced isolation ratings. Typical applications include electric vehicle powertrain and battery management networks, body control modules, industrial PLC and motor drive CAN buses, and building automation nodes - anywhere CAN nodes must be isolated from ground potential differences or bus faults. Design consideration: use split-termination or 120-ohm bus termination per ISO11898-2, and place 100-nF decoupling capacitors close to both VCC1 and VCC2 pins to maintain signal integrity at 5-Mbps CAN FD bit rates. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet alone.
ISO1050DUB - Isolated CAN Transceiver 2500Vrms | TI (Tape & Reel)
The Texas Instruments ISO1050DUB is a galvanically isolated CAN transceiver that meets or exceeds the specifications of the ISO 11898-2 standard, delivering 1 Mbps half-duplex CAN communication with 2500 Vrms silicon oxide (SiO2) isolation in an 8-pin SOP (DUB) package. An isolated CAN transceiver combines a CAN protocol controller interface with galvanic isolation, allowing data transmission between nodes without a direct electrical connection. Within the signal chain hierarchy, it sits between the CAN controller and the physical twisted-pair bus, isolating the logic domain from the bus domain. Isolation prevents ground loops, common-mode noise, and voltage spikes from damaging sensitive controller electronics in industrially noisy environments. Key features include a SiO2 insulation barrier rated 2500 Vrms for the DUB package (the ISO1050DW variant reaches 5000 Vrms), failsafe outputs, low loop delay of 150 ns typical, and 50 kV/us typical transient immunity. Bus-fault protection extends to -40V on the bus pins, and the device operates from -55C to +105C. Both logic and bus sides operate from a 5V supply. Architecturally, the ISO1050 uses an on-chip capacitive SiO2 isolation barrier providing high-speed signal transfer with low power consumption. The transceiver drives CANH and CANL differentially, supports dominant/recessive bus states per ISO 11898-2, and includes thermal shutdown protection on the bus driver. Typical applications include industrial automation networks such as CANopen and DeviceNet, motor drives, building automation, battery management systems, and EV charging stations where ground potential differences exist between nodes. Design tip: use a dedicated isolated DC-DC supply for the bus side and maintain adequate creepage and clearance on the PCB around the barrier. For higher isolation (5000 Vrms), select the ISO1050DW; TI recommends the ISO1042 or ISO1044 as successors for new designs. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet. Pricing as of 2026-09-01 from LCSC listing data.
ISO1050DUBR - Isolated CAN Transceiver 2500Vrms | TI
The Texas Instruments ISO1050DUBR is a galvanically isolated CAN transceiver that meets or exceeds the specifications of the ISO 11898-2 standard, delivering 1 Mbps half-duplex CAN communication with 2500 Vrms silicon oxide (SiO2) isolation in an 8-pin SOP (DUB) package. An isolated CAN transceiver combines a CAN protocol controller interface with galvanic isolation, allowing data transmission between nodes without a direct electrical connection. Within the signal chain hierarchy, it sits between the CAN controller and the physical twisted-pair bus, isolating the logic domain from the bus domain. Isolation prevents ground loops, common-mode noise, and voltage spikes from damaging sensitive controller electronics in industrially noisy environments. Key features include a SiO2 insulation barrier rated 2500 Vrms for the DUB package (the ISO1050DW variant reaches 5000 Vrms), failsafe outputs, low loop delay of 150 ns typical, and 50 kV/us typical transient immunity. Bus-fault protection extends to -40V on the bus pins, and the device operates from -55C to +105C. Both logic and bus sides operate from a 5V supply. Architecturally, the ISO1050 uses an on-chip capacitive SiO2 isolation barrier providing high-speed signal transfer with low power consumption. The transceiver drives CANH and CANL differentially, supports dominant/recessive bus states per ISO 11898-2, and includes thermal shutdown protection on the bus driver. Typical applications include industrial automation networks such as CANopen and DeviceNet, motor drives, building automation, battery management systems, and EV charging stations where ground potential differences exist between nodes. Design tip: use a dedicated isolated DC-DC supply for the bus side and maintain adequate creepage and clearance on the PCB around the barrier. For higher isolation (5000 Vrms), select the ISO1050DW; TI recommends the ISO1042 or ISO1044 as successors for new designs. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet. Pricing as of 2026-09-01 from LCSC listing data.
ISO1050DW - 5V Isolated CAN Transceiver | Texas Instruments
Texas Instruments ISO1050DW is an isolated 5 V CAN transceiver that complies with the ISO11898-2 standard and provides galvanic isolation up to 5000 VRMS in a 16-pin SOIC package. The device supports a maximum CAN data rate of 1 Mbps, has a typical propagation delay of 74 ns, and is specified for a maximum supply voltage of 5.5 V. Its two-channel architecture separates CAN bus and logic domains with a silicon oxide insulation barrier. An isolated CAN transceiver is a network interface device that connects a CAN bus to a host controller while preventing high-voltage and ground-potential differences from propagating between the two systems. Within the signal-chain hierarchy, it combines a CAN physical-layer transceiver, a digital isolator, and logic-side interfaces. This galvanic isolation improves fault containment and lets equipment connected to a CAN bus operate safely when the bus and controller grounds are at different potentials. Key electrical features include 5000 VRMS reinforced isolation for ISO1050DW, low loop delay of 150 ns typical, and transient-immunity capability of 50 kV/s typical. The logic-side and bus-side sections use separate supply domains, while failsafe outputs help define the state of the interface when the bus is inactive. The 16-SOIC package supports conventional surface-mount assembly and provides a clear path from the CAN input/output pins to the isolated logic-side TXD and RXD pins. Technically, the ISO1050 integrates a CAN transceiver with reinforced silicon oxide isolation. The 74 ns propagation-delay specification is important for maintaining stable message timing, while the 150 ns typical loop-delay figure indicates how quickly a transition at TXD can appear at RXD through the device. Its isolation barrier separates the logic input and output buffers from the CAN bus interface, allowing isolated power to be used on the controller side when required by the system architecture. Typical uses include industrial automation equipment, building controls, robotics, electric-vehicle subsystems, and other CAN networks where ground-potential differences are possible. The device is particularly suitable when a robust 1 Mbps bus connection and 5000 VRMS separation are required in a compact 16-pin surface-mount package. Designers should provide separate, properly decoupled supplies to the bus-side and logic-side power pins and connect the CAN transceiver portion to the bus reference ground. The isolation barrier does not replace proper high-voltage layout practices; creepage, clearance, surge protection, and the ratings of external components must follow the complete system isolation plan. This page consolidates verified manufacturer and distributor information, explicit data gaps, sourcing considerations, and design guidance for engineers evaluating the ISO1050DW for isolated CAN links.
ISO1050QDUBRQ1 - 2.5kVRMS Isolated CAN Transceiver | Texas Instruments
The Texas Instruments ISO1050QDUBRQ1 is a galvanically isolated CAN transceiver that meets the specifications of the ISO11898-2 standard, qualified to AEC-Q100 for automotive applications. The device has logic input and output buffers separated by a silicon oxide (SiO2) insulation barrier providing galvanic isolation of up to 2500 VRMS, packaged in an 8-pin SOIC (DUB, R-PDSO-G8) package. An isolated CAN transceiver is a physical-layer interface IC that translates CAN controller logic signals (TXD/RXD) into the differential CANH/CANL bus signals while blocking DC and common-mode transients across the isolation barrier. Isolation is essential in automotive and industrial systems where ground potential differences, noise, and surges exist between the logic domain and the bus domain. Within the power and interface IC hierarchy, the ISO1050 sits between the host MCU and the physical CAN twisted-pair bus. Key features include ISO11898-2 compliance, 2500 VRMS SiO2 isolation (5000 VRMS on the ISO1050DW variant), operation from 5V supplies, and an operating temperature range of -55C to +105C per the Q1 automotive qualification. The single-package integration of the isolation barrier and transceiver simplifies layout compared to discrete optocoupler-plus-transceiver solutions, reducing BOM count and improving timing skew. Technically, the SiO2-based capacitive isolation of the ISO10xx family provides robust, low-power signal transfer with far better aging characteristics and CMTI than optocoupler alternatives. The device integrates the oscillator, modulator, and differential driver/receiver, supporting reliable CAN FD-rate backward compatibility at classic CAN data rates. Typical applications include automotive body electronics and gateways, industrial field bus systems, remote sensing nodes, motor drive control networks, and building automation where isolated CAN rails are required. Used in conjunction with isolated power supplies, the device provides a fully isolated CAN node. Design consideration: keep the isolated-side VCC2 bypass capacitor (100nF ceramic) close to the pin and ensure the PCB creepage/clearance across the barrier follows the DUB package's rated working voltage.
ISO1412DWR - 500kbps Full-Duplex 5kVrms Isolated RS-485/RS-422 | Texas Instruments
The Texas Instruments ISO1412DWR is an EMC-protected, 500-kbps, full-duplex, 5-kVrms-isolated RS-485 and RS-422 transceiver in a 16-pin SOIC package. It is designed for industrial data links requiring galvanic isolation, noise immunity, and robust transient protection. The device supports one transmitter and one receiver, allowing simultaneous bidirectional communication over differential bus pairs. Its 5-kVrms isolation rating helps protect low-voltage host circuitry from high-potential bus environments, while its EMC-focused construction is intended to withstand electrostatic-discharge and electrical-fast-transient disturbances encountered in industrial systems. The ISO1412DWR is specified for operation from -40 °C to 125 °C and uses a 1.71 V to 5.5 V supply range according to available distributor data. The device is supplied in the DW 16-pin SOIC package and is identified as a 1/1 isolated transceiver. ISO1412DWR is positioned for RS-422 and RS-485 links in factory automation, motor drives, photovoltaic inverters, HVAC equipment, building automation, grid infrastructure, and fieldbus gateways. Because the verified source material does not publish a complete pin-by-pin truth table, the datasheet URL should be used to verify pin assignments, termination requirements, bus loading, isolation details, and recommended external components before production release.
ISO1430BDW - 12Mbps Isolated RS-485/RS-422 | Texas Instruments
The Texas Instruments ISO1430BDW is an EMC-protected, galvanically isolated half-duplex RS-485 and RS-422 transceiver designed for industrial communication links. It supports signaling rates up to 12 Mbps and provides 5-kVrms reinforced isolation according to the manufacturer product-page description. The device is packaged in a 16-pin wide-body SOIC, making it suitable for high-speed half-duplex bus systems that require electrical separation between the host interface and the external communications bus. Its integrated isolation and EMC protection are intended to simplify industrial interface design, particularly when connected to remote sensors, controllers, test equipment, or process-monitoring systems. The ISO1430 family also supports RS-485 and RS-422 applications in harsh industrial environments, where bus pins may be exposed to electrostatic-discharge and electrical-fast-transient disturbances. The ISO1430BDW is a single-transceiver device, meaning one package provides one isolated half-duplex RS-485/RS-422 channel. Its 12-Mbps capability is substantially faster than the 500-kbps ISO141x family, while remaining below the 50-Mbps ISO145x family. This makes the ISO1430 a useful middle-speed choice when data throughput and EMI immunity matter more than maximum-rate signaling. Designers should confirm the exact electrical limits, isolation ratings, supply requirements, temperature range, and pin-level connection details in the Texas Instruments ISO1430 datasheet before layout. The SOIC package requires careful creepage and clearance planning around the isolation barrier, while the bus interface requires termination, protection, and grounding practices appropriate to the installed cable and system topology.
ISO1430BDWR - 12Mbps Isolated RS-485/RS-422 | Texas Instruments (Tape & Reel)
The Texas Instruments ISO1430BDWR is an EMC-protected, galvanically isolated half-duplex RS-485 and RS-422 transceiver designed for industrial communication links. It supports signaling rates up to 12 Mbps and provides 5-kVrms reinforced isolation according to the manufacturer product-page description. The device is packaged in a 16-pin wide-body SOIC, making it suitable for high-speed half-duplex bus systems that require electrical separation between the host interface and the external communications bus. Its integrated isolation and EMC protection are intended to simplify industrial interface design, particularly when connected to remote sensors, controllers, test equipment, or process-monitoring systems. The ISO1430 family also supports RS-485 and RS-422 applications in harsh industrial environments, where bus pins may be exposed to electrostatic-discharge and electrical-fast-transient disturbances. The ISO1430BDWR is a single-transceiver device, meaning one package provides one isolated half-duplex RS-485/RS-422 channel. Its 12-Mbps capability is substantially faster than the 500-kbps ISO141x family, while remaining below the 50-Mbps ISO145x family. This makes the ISO1430 a useful middle-speed choice when data throughput and EMI immunity matter more than maximum-rate signaling. Designers should confirm the exact electrical limits, isolation ratings, supply requirements, temperature range, and pin-level connection details in the Texas Instruments ISO1430 datasheet before layout. The SOIC package requires careful creepage and clearance planning around the isolation barrier, while the bus interface requires termination, protection, and grounding practices appropriate to the installed cable and system topology.
ISO1432BDW - 12Mbps Isolated RS-485/RS-422 Transceiver | TI
The Texas Instruments ISO1432BDW is an EMC-protected, galvanically isolated RS-485 and RS-422 transceiver designed for reliable full-duplex data communication. It supports data rates up to 12 Mbps and provides 5 kVrms isolation, making it suitable for industrial, communications, and equipment interfaces that require robust protection against electromagnetic interference and high-voltage ground potential differences. The device is supplied in a 16-pin SOIC package and is specified for operation from -40 °C to +125 °C. An isolated transceiver is a type of interface IC that combines a differential line driver and receiver with an internal isolation barrier. The isolation barrier separates the logic-side supply and signals from the bus-side interface, helping prevent ground loops and allowing communication between equipment located at different ground potentials. The ISO1432 belongs to the broader interface-IC and communication-transceiver hierarchy, with RS-485 and RS-422 differential signaling designed for noise-resistant data transfer over cables. The ISO1432BDW is identified as a one-channel full-duplex transceiver with EMC protection. Full-duplex operation provides separate transmit and receive paths, allowing simultaneous bidirectional communication when the system requires it. The 12 Mbps maximum signaling rate supports high-speed industrial links, while the 5 kVrms isolation rating provides a substantial barrier between the two sides of the interface. The manufacturer product information identifies the family as an RS-485 and RS-422 transceiver and describes it as EMC protected. The DW package designation identifies the 16-pin SOIC outline used by this orderable variant. The part is suitable for industrial equipment, factory automation, data acquisition, building controls, and other installations where the interface must withstand electrically noisy environments. The isolation barrier and EMC-focused design are particularly useful when long cables, switching converters, motors, relays, or grounded subsystems can introduce transients and potential differences into a communication link. Designers should verify the complete pinout, isolation requirements, bus termination, common-mode range, supply sequencing, and maximum exposed-pad or package thermal constraints against the manufacturer datasheet before production release. The 16-pin SOIC footprint should be matched exactly to the DW package drawing, and the logic-side and bus-side isolation domains must be treated as separate electrical domains. Cable shielding, chassis grounding, surge protection, and appropriate common-mode protection should be evaluated for the intended installation. This product data combines Texas Instruments family information, distributor availability references, package details, and verified comparison data for engineering selection. It is intended to help engineers identify whether the ISO1432BDW meets the required communication rate, isolation level, package, temperature range, and EMC-protection needs before comparing it with alternative isolated transceiver implementations.
ISO1432DW - 12Mbps Isolated Full-Duplex RS-485/RS-422 Transceiver | TI
The Texas Instruments ISO1432DW is an EMC-protected, 12-Mbps, full-duplex, 5-kVrms isolated RS-485 and RS-422 transceiver housed in a 16-pin SOIC (DW) package. The device integrates a galvanic isolation barrier with reinforced insulation rated at 5 kVrms, a 1/1 (one driver, one receiver) full-duplex channel, and TI's proprietary EMC hardening for industrial bus robustness. Operating from a 3 V to 5.5 V supply, it supports data rates up to 12 Mbps and replaces discrete opto-isolator plus transceiver solutions with a single IC. An isolated RS-485 transceiver is a galvanically-isolated differential line driver/receiver designed for TIA/EIA-485-A and TIA/EIA-422-A applications. Within a system hierarchy, it sits at the interface between a low-voltage controller (MCU, FPGA, DSP) and a long-distance, noise-prone industrial bus. The isolation barrier blocks high-voltage transients, ground-potential differences, and common-mode noise that would otherwise couple into sensitive digital or analog circuitry upstream. By eliminating external optocouplers and isolated DC/DC converters (when paired with an integrated power isolator companion), the ISO1432 simplifies BOM, reduces board area, and improves reliability versus discrete implementations. Key features include 5-kVrms reinforced isolation per UL 1577, 12 Mbps maximum signaling rate, 1/1 full-duplex topology with separate driver output (Y/Z) and receiver input (A/B) pins, integrated bus protection including IEC 61000-4-2 ESD (typically 8 kV contact / 15 kV air) and IEC 61000-4-4 electrical fast transient immunity, and a wide 3 V to 5.5 V supply range. The device operates across -40 °C to +125 °C, suiting outdoor, cabinet-mounted, and motor-drive environments. The 16-pin DW SOIC footprint provides a creepage/clearance distance consistent with reinforced insulation requirements, simplifying PCB layout for high-voltage spacing. Internally, the ISO1432 uses TI's silicon-oxide (SiO2) capacitive isolation barrier combined with an RS-485 transceiver die on each side. The high-speed differential driver delivers 1.5 V minimum output swing into a 54 Ω load per TIA/EIA-485, while the receiver offers 50 mV typical hysteresis and a 1/8-unit-load input impedance (allowing up to 256 nodes on the bus when used with other 1/8-load parts). The EMC hardening includes spread-spectrum OOK signaling across the barrier and integrated surge protection on the bus pins, eliminating the need for external TVS diodes in many applications. Typical applications include industrial programmable logic controllers (PLCs), factory automation and field-bus networks, motor-control inverter gate-driver communication, solar inverter H-bridge control interfaces, building-automation RS-485 trunks, and any microcontroller-to-bus interface requiring reinforced isolation. The wide temperature range also suits outdoor instrumentation and renewable-energy installations. When designing with the ISO1432, allocate at least 8 mm of creepage on the PCB beneath and between the SOIC package sides to preserve the 5 kVrms rating, and pair the part with a wide-Vin isolated DC/DC (such as the ISOW1044 or ISOW1412 companion families) when the bus side must remain powered during MCU brownouts. Decouple both VCC1 and VCC2 with 1 µF X7R ceramic capacitors placed within 2 mm of the supply pins to keep digital switching currents off the isolation barrier. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.
ISO1432DWR - 12Mbps Isolated Full-Duplex RS-485/RS-422 Transceiver | TI (Tape & Reel)
The Texas Instruments ISO1432DWR is an EMC-protected, 12-Mbps, full-duplex, 5-kVrms isolated RS-485 and RS-422 transceiver housed in a 16-pin SOIC (DW) package. The device integrates a galvanic isolation barrier with reinforced insulation rated at 5 kVrms, a 1/1 (one driver, one receiver) full-duplex channel, and TI's proprietary EMC hardening for industrial bus robustness. Operating from a 3 V to 5.5 V supply, it supports data rates up to 12 Mbps and replaces discrete opto-isolator plus transceiver solutions with a single IC. An isolated RS-485 transceiver is a galvanically-isolated differential line driver/receiver designed for TIA/EIA-485-A and TIA/EIA-422-A applications. Within a system hierarchy, it sits at the interface between a low-voltage controller (MCU, FPGA, DSP) and a long-distance, noise-prone industrial bus. The isolation barrier blocks high-voltage transients, ground-potential differences, and common-mode noise that would otherwise couple into sensitive digital or analog circuitry upstream. By eliminating external optocouplers and isolated DC/DC converters (when paired with an integrated power isolator companion), the ISO1432 simplifies BOM, reduces board area, and improves reliability versus discrete implementations. Key features include 5-kVrms reinforced isolation per UL 1577, 12 Mbps maximum signaling rate, 1/1 full-duplex topology with separate driver output (Y/Z) and receiver input (A/B) pins, integrated bus protection including IEC 61000-4-2 ESD (typically 8 kV contact / 15 kV air) and IEC 61000-4-4 electrical fast transient immunity, and a wide 3 V to 5.5 V supply range. The device operates across -40 °C to +125 °C, suiting outdoor, cabinet-mounted, and motor-drive environments. The 16-pin DW SOIC footprint provides a creepage/clearance distance consistent with reinforced insulation requirements, simplifying PCB layout for high-voltage spacing. Internally, the ISO1432 uses TI's silicon-oxide (SiO2) capacitive isolation barrier combined with an RS-485 transceiver die on each side. The high-speed differential driver delivers 1.5 V minimum output swing into a 54 Ω load per TIA/EIA-485, while the receiver offers 50 mV typical hysteresis and a 1/8-unit-load input impedance (allowing up to 256 nodes on the bus when used with other 1/8-load parts). The EMC hardening includes spread-spectrum OOK signaling across the barrier and integrated surge protection on the bus pins, eliminating the need for external TVS diodes in many applications. Typical applications include industrial programmable logic controllers (PLCs), factory automation and field-bus networks, motor-control inverter gate-driver communication, solar inverter H-bridge control interfaces, building-automation RS-485 trunks, and any microcontroller-to-bus interface requiring reinforced isolation. The wide temperature range also suits outdoor instrumentation and renewable-energy installations. When designing with the ISO1432, allocate at least 8 mm of creepage on the PCB beneath and between the SOIC package sides to preserve the 5 kVrms rating, and pair the part with a wide-Vin isolated DC/DC (such as the ISOW1044 or ISOW1412 companion families) when the bus side must remain powered during MCU brownouts. Decouple both VCC1 and VCC2 with 1 µF X7R ceramic capacitors placed within 2 mm of the supply pins to keep digital switching currents off the isolation barrier. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.
ISO1540D - 2.5kVrms I2C Digital Isolator | Texas Instruments
The Texas Instruments ISO1540D is a low-power, bidirectional I2C-compatible digital isolator providing galvanic isolation up to 2500Vrms. It supports data rates up to 1 Mbps from a 3V to 5.5V supply, housed in an 8-pin SOIC package (0.154in / 3.90mm width) with open-drain outputs rated 3.5mA sink current on Side 1 and 35mA on Side 2, operating from -40C to +125C. A digital isolator transfers digital signals across an isolation barrier, preventing DC and ground-loop current flow while allowing data to pass. Digital isolators are core building blocks in power management hierarchies, replacing optocouplers with higher speed, better reliability, longer life, and smaller footprint. The ISO1540D specifically addresses I2C buses, whose open-drain, bidirectional clock and data lines require specialized direction-handling logic that general-purpose digital isolators cannot provide. Key features include bidirectional SCL and SDA channels that isolate the I2C bus without external direction control, 1-MHz (fast-mode) operation, and 25kV/us common-mode transient immunity (CMTI) for robust operation in noisy power environments. The open-drain outputs integrate directly into standard I2C topologies with external pull-up resistors on both sides of the barrier. Technically, the ISO1540D uses TI capacitive isolation technology with a silicon dioxide (SiO2) barrier, delivering high isolation robustness and long-term reliability with a typical propagation delay of 67ns, preserving I2C timing margins. The wide 3V to 5.5V supply range allows 3.3V-to-5V logic domain crossing across the barrier. Typical applications include isolated I2C sensor interfaces in industrial automation, battery management systems (BMS), power supplies, motor drives, and medical monitoring equipment, where the ISO1540D separates control electronics from high-voltage or noisy power stages. Design tip: size pull-up resistors on both sides according to bus capacitance and the 1-Mbps data rate, and place 0.1uF decoupling capacitors close to both supply pins, as current pricing of roughly $2 to $4 per unit (as of 2026-08-29) makes it cost-effective to use one isolator per isolated bus segment.
ISO6442 - Quad-Channel Digital Isolator 150Mbps | Texas Instruments
The Texas Instruments ISO6442 is a robust EMC, general-purpose quad-channel digital isolator with a 2/2 channel configuration (two forward, two reverse channels), supporting data rates up to 150 Mbps and a common-mode transient immunity (CMTI) of up to 250 kV/us. It is available in a 16-pin wide-body SOIC (DWR, 5000 Vrms reinforced isolation) and a 16-pin SSOP (DBQ, 3000 Vrms basic isolation). A digital isolator is a component that transfers digital signals across a galvanic isolation barrier, blocking high voltages, isolating ground potentials, and preventing noise currents between two sides of a circuit. Within the interface-IC hierarchy, digital isolators sit between logic controllers and high-voltage or noisy domains such as motor drives, inverters, and fieldbus networks. The ISO6442 belongs to TI's ISO644x family of basic and reinforced quad-channel isolators built on a proprietary capacitive isolation architecture using an SiO2 dielectric barrier. Key features include the wide 2.25 V to 5.5 V supply range on both sides, enabling direct interfacing with 1.8 V, 2.5 V, 3.3 V, and 5 V logic; a fail-safe default output of high for the standard ISO6442 during input power or signal loss (the ISO6442F defaults low); and robust EMC performance for harsh industrial noise environments. The reinforced DWR package supports sustained working-voltage isolation requirements. Architecturally, the device modulates the input signal across the capacitive barrier and reconstructs it at the output, delivering low power, high speed, and stable propagation characteristics over temperature and supply variation. Enable pins provide tri-state output control for power management and multipoint bus applications. Typical applications include isolated SPI interfaces, industrial fieldbus communication, motor drives, power inverters, battery management systems, and on-board chargers, where 150 Mbps throughput and 250 kV/us CMTI maintain signal integrity in electrically noisy conditions. When designing, maintain adequate creepage and clearance on the PCB, place 0.1 uF bypass capacitors close to both VCC pins, and verify that propagation delay and pulse-width distortion near 150 Mbps meet the timing requirements of the receiving peripheral.
ISO6442-Q1 - 150Mbps Quad-Channel Digital Isolator | TI
The Texas Instruments ISO6442-Q1 is an automotive-grade quad-channel digital isolator providing two forward and two reverse channels, a data rate up to 150 Mbps, and a common-mode transient immunity (CMTI) of 250 kV/us. The device is qualified to AEC-Q100 for automotive use and is available in reinforced and basic isolation ratings, with the ISO6442DBQRQ1 ordering option packaged in a 16-pin SSOP (DBQ) rated 3000 Vrms. A digital isolator is an integrated circuit that transmits digital signals across a galvanic isolation barrier, blocking high voltages, ground loops, and common-mode noise while passing logic data. Within the interface-IC hierarchy, digital isolators sit between a controller and noisy or high-voltage circuitry, complementing isolated transceivers, gate drivers, and isolated ADCs in systems requiring safety and signal integrity. Key features include the 250 kV/us CMTI, which keeps outputs correct in high-dv/dt environments such as motor-drive inverter legs, and the 150 Mbps data rate supporting fast SPI and parallel logic links. Enable pins allow each direction to be tri-stated for power management. In the event of input power or signal loss, default outputs are high; the ISO6442F-Q1 variant defaults low, giving designers a choice of fail-safe behavior. The ISO6442-Q1 uses TI's proven capacitive isolation technology, delivering robust EMC performance and long-term barrier reliability. The ISO644x-Q1 family (ISO6440/6441/6442 and F variants) shares package options including the DW-16 wide SOIC, DFP-16 wide SSOP, and DBQ-16 SSOP; a Functional Safety FIT rate and pin FMA document (SFFSB42) is available. Typical applications include EV battery management systems, isolated SPI links to current and voltage monitors, motor drives and inverters, and industrial fieldbus isolation. For reliable design, keep copper under the isolation barrier clear, decouple both VCC pins closely, and select the F-suffix variant when a low default output is required for safe power-loss behavior.