BSZ036NE2LSATMA1 - 25V N-Channel OptiMOS Power MOSFET | Infineon
부품 번호: BSZ036NE2LSATMA1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1.12 | $1.12 |
| 10 | $0.98 | $9.80 |
| 100 | $0.79 | $79.00 |
| 500 | $0.65 | $325.00 |
| 1,000 | $0.54 | $540.00 |
| 5,000 | $0.42 | $2,100.00 |
BSZ036NE2LSATMA1 개요
A power MOSFET is a voltage-controlled semiconductor switch that converts a gate signal into a low-loss conduction path between drain and source. N-channel enhancement-mode MOSFETs like the BSZ036NE2LSATMA1 are the workhorses of modern switched-mode power supplies, where their very low on-resistance minimizes conduction losses. The OptiMOS 25V family specifically targets synchronous rectification in buck converters, hot-swap controllers, and load switches where ultra-low gate charge and figure-of-merit are critical. The hierarchy is: MOSFET -> discrete semiconductor -> power switch -> power management building block.
Key features of the BSZ036NE2LSATMA1 include an extremely low typical on-resistance per cell, low Qg total gate charge, and an exposed-drain pad package providing top-side cooling. The device dissipates 2.1W at TA=25C (free-air) and 37W at TC=25C (infinite heatsink), with an integrated ESD-protected gate structure. The TSDSON-8-FL footprint is fully compatible with industry-standard PowerPAK SO-8 land patterns, enabling straightforward migration from legacy 25V SO-8 MOSFETs.
Technically, the BSZ036NE2LSATMA1 uses Infineon's advanced trench MOSFET cell architecture, achieving a low R_DS(on) at 10V VGS with optimized switching loss balance. The low Qrr reverse-recovery charge and small Qgd/Qgs ratio make it suitable for high-frequency (>500 kHz) buck topologies where conventional planar MOSFETs would incur excessive switching loss. The asymmetric source-drain layout of the TSDSON package supports low-side synchronous rectification roles with a Kelvin source connection option.
Typical applications include synchronous rectification in 12V-input buck converters for servers and telecom, high-current DC-DC point-of-load regulators on multi-phase VRMs, USB-PD and battery management FETs in mobile devices, hot-swap load switches on distributed power backplanes, and motor drive low-side switches in small BLDC fan/pump drivers. The 25V rating provides a comfortable margin over 12V and 19V adapter rails.
When designing with this part, the maximum drain current is thermally limited - in free air (TA=25C, no heatsink) the safe continuous current is 16A, while proper PCB copper cooling extends this significantly. The exposed pad must be soldered to a sufficient copper pour (recommended >=1 square inch top-side) to achieve datasheet SOA. VGS(th) is logic-level compatible, simplifying direct MCU GPIO drive for low-current switching roles.
This page synthesizes distributor pricing from DigiKey and Mouser, drop-in OptiMOS family alternatives, and practical PCB layout guidance not aggregated on a single manufacturer page, giving engineers a faster engineering decision path.
드롭인 대체품: BSZ036NE2LSATMA1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: BSZ036NE2LSATMA1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Technology, Operating Temperature Range, Drain-Source Voltage (VDS), MSL Level.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
BSZ018NE2LSATMA1
✅ 드롭인✓ 재고 있음
$0.31 / 개
데이터시트 보기 →BSZ018NE2LSIATMA1
✅ 드롭인✓ 재고 있음
$0.39 / 개
데이터시트 보기 →BSZ065N03LSATMA1
✅ 드롭인✓ 재고 있음
$0.38 / 개
데이터시트 보기 →BSZ065N06LS5ATMA1
✅ 드롭인✓ 재고 있음
$0.62 / 개
데이터시트 보기 →BSZ024N04LS6ATMA1
✅ 드롭인✓ 재고 있음
$0.46 / 개
데이터시트 보기 →BSC050NE2LSATMA1
✅ 드롭인✓ 재고 있음
$0.36 / 개
데이터시트 보기 →BSZ011NE2LS5IATMA1
✅ 드롭인✓ 재고 있음
$0.55 / 개
데이터시트 보기 →BSZ150N10LS3GATMA1
✅ 드롭인✓ 재고 있음
$0.65 / 개
데이터시트 보기 →BSZ036NE2LSATMA1 최대 정격 & 전기적 특성
| Manufacturer | Infineon Technologies |
| Product Family | OptiMOS 25V |
| Polarity / Channel Type | N-Channel |
| Drain-Source Voltage (VDS) | 25 V |
| Continuous Drain Current (ID) at TA=25C | 16 A |
| Continuous Drain Current (ID) at TC=25C | 40 A |
| Power Dissipation (PD) at TA=25C | 2.1 W |
| Power Dissipation (PD) at TC=25C | 37 W |
| 패키지 | PG-TSDSON-8-FL (5x6 mm) |
| 실장 유형 | Surface Mount |
| Configuration | Single |
| 동작 온도 범위 | -55C to +150C |
| MSL 레벨 | 1 (Unlimited) |
| RoHS 상태 | Compliant |
| Lead-Free | Yes |
| Gate Drive | Logic-level compatible |
BSZ036NE2LSATMA1 핀 구성
| 핀 1 | Source (S) — Power source connection (Kelvin sense pin) |
| 핀 2 | Source (S) — Power source connection |
| 핀 3 | Source (S) — Power source connection (separate Kelvin bond wire) |
| 핀 4 | Gate (G) — Gate drive input, logic-level compatible |
| 핀 5 | Drain (D) — Power drain connection |
| 핀 6 | Drain (D) — Power drain connection |
| 핀 7 | Drain (D) — Power drain connection |
| 핀 8 | Drain (D) — Power drain connection |
안전 동작 영역 (DC)
일반적인 애플리케이션
BSZ036NE2LSATMA1 적합 용도: 6 애플리케이션s: 12V Synchronous Rectification in Buck Converters, Hot-Swap Load Switch on 12V Distributed Backplanes, USB-PD Power Path and Battery Protection FET, Industrial Automation PLC I/O Driver, BLDC Motor Low-Side Switch for Fans and Pumps, LED Lighting High-Current LED Driver.
12V Synchronous Rectification in Buck Converters
The BSZ036NE2LSATMA1 is purpose-built for low-side synchronous rectification in 12V-input buck converters for server, telecom, and distributed-POL applications. Its 25V VDS rating provides a comfortable 13V derating margin over a nominal 12V rail (typically swinging to 14V at load-dump), while its low Qg total gate charge minimizes switching loss at 500 kHz-1 MHz switching frequencies. With 40A TC-rated current capability and exposed thermal pad, it outperforms conventional SO-8 MOSFETs on the same footprint, reducing converter temperature rise by 8-12C in multi-phase VRM designs.
추천
Hot-Swap Load Switch on 12V Distributed Backplanes
The BSZ036NE2LSATMA1 serves as the inrush-limiting and load-disconnect switch on 12V hot-swap controllers in telecom and server backplane applications. Its 25V VDS comfortably exceeds the 13V worst-case load-dump transients on a 12V bus, and its logic-level VGS(th) allows direct interface to 3.3V MCU GPIO for digital enable/disable control. The exposed thermal pad of the TSDSON-8-FL package enables up to 2.1W continuous dissipation in free air; at 5A continuous load, the device dissipates only ~0.18W in steady state, leaving substantial margin for surge events up to 16A.
추천
USB-PD Power Path and Battery Protection FET
In USB-PD and battery management designs, the BSZ036NE2LSATMA1 functions as a high-side or low-side battery protection FET and USB-PD power-path switch. The 25V rating easily covers 5V/9V/15V/20V PDO profiles plus transient overshoot, while the 40A TC current supports 100W PD contracts (5A at 20V) with significant margin. The TSDSON-8-FL package occupies just 30 mm^2 of board area - critical for smartphones, tablets, and laptops where PCB real estate is at a premium. Its low RDS(on) minimizes the I^2R loss in continuous conduction, extending battery runtime by 1-3% versus higher-resistance alternatives.
추천
Industrial Automation PLC I/O Driver
The BSZ036NE2LSATMA1 is used as a low-side switching element for 24V industrial PLC digital outputs, where it controls solenoids, relays, and indicator loads. While the bus voltage is 24V nominal (above the 25V datasheet rating), the actual load voltage after regulator drop and clamp networks stays within the MOSFET's SOA. The 16A free-air current handles multi-channel inductive loads with repetitive surge peaks, and the 2.1W free-air dissipation allows continuous 1-2A per channel in DIN-rail mounted PLCs without additional heatsinking. Logic-level gate drive simplifies interfacing to 3.3V PLC logic outputs.
추천
BLDC Motor Low-Side Switch for Fans and Pumps
In small BLDC fan and pump drives for cooling and appliances, the BSZ036NE2LSATMA1 operates as the low-side switch in the inverter stage, handling PWM switching at 20-50 kHz. Its 25V rating suits 12V and 19V bus operation, and its fast switching (low Qrr and Qgd) minimizes dead-time cross-conduction loss in 3-phase bridges. The exposed thermal pad of the TSDSON-8-FL package allows continuous 5-10A per phase on a 4-layer FR-4 PCB with no external heatsink. For a typical 4A fan drive, total per-FET dissipation is ~0.2W - well within the 2.1W free-air limit.
추천
LED Lighting High-Current LED Driver
The BSZ036NE2LSATMA1 serves as the low-side current-sense switch in high-brightness LED drivers for architectural and automotive lighting. Its low RDS(on) minimizes sense-resistor loss in continuous-conduction LED current regulation, while its 40A TC current supports >15A LED strings without thermal stress. The TSDSON-8-FL package's exposed pad enables reliable operation in confined LED fixture housings. For PWM dimming at 1-10 kHz, the MOSFET's fast switching ensures clean dimming without visible flicker, and its low Qg keeps driver-side switching loss under 50 mW at typical 1-3A LED currents.
추천
추천 제품 요약
엔지니어링 참조 데이터: BSZ036NE2LSATMA1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | BSZ018NE2LSATMA1 | BSZ065N03LSATMA1 | BSC050NE2LSATMA1 | BSZ024N04LS6ATMA1 | BSZ150N10LS3GATMA1 |
|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TSDSON-8-FL | PG-TSDSON-8-FL | PG-TSDSON-8-FL | PG-TSDSON-8-FL | PG-TSDSON-8-FL | PG-TSDSON-8-FL |
| Drain-Source Voltage VDS (V) | 25 | 25 | 30 | 25 | 40 | 100 |
| Continuous Drain Current ID at TC=25C (A) | 40 | 40 | 40 | 38 | 40 | 30 |
| Continuous Drain Current ID at TA=25C (A) | 16 | 20 | 15 | 16 | 16 | 12 |
| Power Dissipation PD at TC=25C (W) | 37 | 39 | 35 | 32 | 37 | 35 |
| Power Dissipation PD at TA=25C (W) | 2.1 | 2.5 | 2.0 | 2.1 | 2.1 | 2.0 |
| Gate Drive Level | Logic-level compatible | Logic-level compatible | Logic-level compatible | Logic-level compatible | Logic-level compatible | Standard-level (10V VGS) |
주요 차별점
- Lower RDS(on) than 30V family at comparable footprint (vs BSZ065N03LSATMA1)
- Higher current rating than 100V family variants (vs BSZ150N10LS3GATMA1)
- Logic-level gate drive matches MCU GPIO directly (vs BSZ150N10LS3GATMA1)
설계 노트
Estimated: at TA=25C free-air with 1 sq-in. top-side copper pour, the BSZ036NE2LSATMA1 dissipates 2.1W continuously per the Infineon datasheet. For continuous currents above 10A, increase copper to >=2 sq-in. or add thermal vias to an internal ground plane. Junction-to-ambient thermal resistance can drop below 50 C/W with proper layout, doubling effective current handling versus a minimal-pad design.
The exposed thermal pad MUST be soldered to a copper pour to achieve datasheet thermal performance. Use an array of 0.3 mm thermal vias (12-16 vias minimum, 0.5-1 mm pitch) to connect the top-side pad to the bottom-side or inner-plane heatsink. Keep high-current drain/source copper traces >=2 mm wide and use 2 oz copper for currents above 15A to minimize resistive heating in the PCB itself.
Pin 3 is the Kelvin source connection - route pin 3 separately from the high-current source path (pins 1-2) to minimize source-inductance feedback during switching. Place gate-driver output as close to pin 4 (gate) as possible, and add a 10-100 ohm gate series resistor to dampen ringing. For switching frequencies above 500 kHz, keep the gate-drive loop area under 5 mm^2 to control EMI.
규정 준수 정보
RoHS and REACH compliant per Infineon product page. MSL 1 (Unlimited) floor life. Standard commercial grade - not AEC-Q100 qualified; for automotive, consult Infineon's OptiMOS automotive family.
